Skip to content

how to replace valve cover gasket o rings on 2002 isuzu rodeo

You search PDF repair manual about how to replace valve cover gasket o rings on 2002 isuzu rodeo, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Ford Lincoln LS Valve Cover LH Workshop Manual

download
Valve Cover LH Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 3. Remove the air cleaner housing. 1. Disconnect the mass air flow (MAF) sensor electrical connector. 2. Remove the bolt. 3. Remove the housing. 4. CAUTION: To disconnect the Norma fitting, squeeze the tabs and pull straight out or damage to the fitting can occur. Disconnect the crankcase ventilation tube. 5. Disconnect the fuel hose. For additional information, refer to Section 310-00 . 6. Disconnect the evaporative emission canister purge valve hose. 7. Remove the vapor management valve (VMV) cover. SECTION 303-01B: Engine — 3.9L 2002 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/17/2001 Material Item Specification 8. Remove the VMV. 1. Disconnect the vacuum hose. 2. Disconnect the purge hose. 3. Disconnect the electrical connector and the push pin. 4. Remove the nuts and the valve. 9. Remove the exhaust gas recirculation (EGR) vacuum regulator solenoid. 1. Disconnect the electrical connector. 2. Remove the screws and the EGR vacuum regulator solenoid. 10. Remove the bracket. 1. Remove the hose. 2. Remove the bracket. 11. Position the engine wiring harness up. 12. Remove the ignition coil cover. * Inspect the gasket and install a new gasket as necessary.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models: