tighten camshaft pulley motor chevy venture

You search PDF repair manual about tighten camshaft pulley motor chevy venture, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tighten camshaft pulley motor chevy venture Direct Download speed 5432 Kb/s

  tighten camshaft pulley motor chevy venture Full Version speed 8172 Kb/s



2002 HONDA ACCORD – Timing Belt and Balancer Belt Installation Instructions

0

Filed Under (Honda Manuals) by admin on 22-01-2011

download
1. Remove and clean the balancer belt drive pulley. 2. Clean the timing belt pulleys, and the upper and lower timing cover. 3. Set the crankshaft to TDC. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head. -1 Drive pulley (A). -2 Tensioner pulley (B). -3 Water pump pulley (C). -4 Camshaft pulley (D). 6. Loosen and retighten the adjusting nut to tension the timing belt. 7. Clean any oil off both faces of the balancer belt drive pulley. 8. Check the lower cover rubber seal for cracks and other damage. NOTE: ?If the rubber seal is coming off, apply liquid gasket to the lower cover and reinstall the rubber seal. Wipe off any liquid gasket that is pressed out. ?When replacing the rubber seal, clean the lower cover groove, cut the repair rubber seal to length, and put the rubber seal into the groove evenly. 9. Install the balancer belt drive pulley and the lower cover. 10. Temporarly install the crankshaft pulley and bolt. 11. Rotate the crankshaft pulley five or six turns counterclockwise to seat the timing belt on the pulleys. 14. Check the camshaft pulley marks. ?If the camshaft pulley marks are also at TDC, go to step 15. ?If the camshaft pulley marks are not at TDC, remove the timing belt and repeat steps 3, 4 and 5. 15. Remove the crankshaft pulley and the lower cover. 16. Turn the crankshaft to TDC again. 17. Lock the timing belt adjuster arm in place with one of the 6 mm timing cover bolts. 18. Loosen the adjusting nut 2/3-1 turn, and make sure the balancer belt tensioner moves freely. Then push the tensioner up and retighten the adjusting nut. 19. Align the rear balancer shaft pulley with a 6 x 100 mm bolt (or equivalent). -1 Remove the bolt (A) and washer (B) from the maintenance hole (C). -2 Scribe a line on a 6 x 100 mm bolt, 74 mm (2.9 in) from the end

Related Content:

2002 honda accord 2 3 timing belt tension adjustment, toyota2y engine only starts when rocker shaft has been loosened, 2005 audi 3 2 tdc diagram, 2006 kia sorento camshaft pulley repair manual pdf, how to replace a tensioner pulley on a 2006 mazda 5, 2003 buick lasabre serpentine belt idler pulley torque spec, mazda 6 crankshaft tool, pulley configuration 2001 buick lesabre, Residue from serpentine bolt on smooth pulleys, lincoln ls crank pulley diagram

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, montero crank shaft pully removal, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, mitsubishi montero sport belt tension bolt pivot, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero

1996 TOYOTA T100 ENGINE MECHANICAL TIMING BELT INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 24-09-2011

download
1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on the timing pulley, facing the flange side inward. 2. INSTALL NO. 1 IDLER PULLEY AND NO.2 IDLER PULLEY (a) Using a 10 mm hexagon wrench, install the No.1 idler pulley with the plate washer and bolt. Torque: 35 N·m (350 kgf·cm, 26 ft·lbf) (b) Check that the pulley bracket moves smoothly. (c) Install the No.2 idler pulley with the bolt. Torque: 40 N·m (400 kgf·cm, 30 ft·lbf) (d) Check that the pulley moves smoothly. 3. TEMPORARILY INSTALL TIMING BELT NOTICE: The engine should be cold. (a) Use the crankshaft pulley bolt to turn the crankshaft and align the timing marks on the crankshaft timing pulley and on the oil pump body. (b) Remove any oil or water on the crankshaft timing pulley, idler pulley and water pump pulley, and keep them clean. NOTICE: Only wipe the pulleys; do not use any cleansing agent. (c) Align the installation mark on the timing belt with the drilled mark of the crankshaft timing pulley. (d) Install the timing belt on the crankshaft timing pulley, No.1 idler and water pump pulleys. 4. INSTALL TIMING BELT GUIDE Install the guide, facing the cup side outward

Related Content:

kia sedona idler pulley bolt lb ft, 1989 mazda b2200 crankshaft pulley bolt tightening torque, location of idler pullies on 3 8 supercharged buick 1998 riviera, how to replace idler pulley 2003 town and country, how to remove idler pulley from 2002 chrysler town and country, how to change a idler pulley on a 2000 tundra, ej22 water pump idler pulley torque, crankshaft pulley installer tool 2006 pt cruiser 2 4 engine, 2007 maxima idel pulley diagram, 1998 honda civic idler arm you tube replacement instructions

2004 Mitsubishi Lancer O-Z Rally TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 06-06-2012

download
Fig. 79: Aligning Timing Belt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow. 4. Temporarily tighten the tensioner pulley bolt. 5. Remove the timing belt. Fig. 80: Tightening Tensioner Pulley Bolt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. INSTALLATION SERVICE POINTS >> A << TIMING BELT INSTALLATION CAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction. CAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position. 1. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Then temporarily tighten tensioner bolt. Fig. 81: Adjusting Timing Belt Tensioner Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Align each of the camshaft and crankshaft sprocket timing marks. 3. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose. 1. Crankshaft sprocket 2. Water pump sprocket 3. Camshaft sprocket 4. Tensioner pulley >> B << TIMING BELT TENSION ADJUSTMENT 1. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4-1/2 turn, and use the force of the tensioner spring to apply tension to the belt. 2. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.

Related Content:

code p0765 mitsubishi montero, p2263 mitsubishi canter, 2005 mazda 3 2 3l push rod clearance, manual book 1G FE throtle sensor, mitsubishi canter 4m51 engine manual, P0087 Mitsubishi cante, p0087 mitsubishi canter, p0404 mitsubishi canter

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

0

Filed Under (Toyota Manuals) by admin on 27-04-2012

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

Related Content:

toyota 1g engine manual, 2008 saturn vue v6 camshaft position actuator solenoid location, toyota 1g fe vvt-i engine service manual, torque settings for toyota 1g fe, www pdfrepairmanual com/search/toyota 1g fe engine, toyota 1g-fe workshop manual, crank shaft torque specs 2000 passat 2 8 30valve v6, 1gfe timing marks, 06 Mazda 6 DTC p1349, 1g-fe camshaft timing marks /pdf

2003 Lexus ES 300 TIMING BELT Removal And Installation Manual

0

Filed Under (Lexus Manuals) by admin on 04-07-2012

download
TIMING BELT Removal (ES 300) 1. Raise and support vehicle. Remove right side front wheel. Remove right fender apron seal. Remove accessory drive belts. Lower vehicle. Disconnect engine coolant reservoir hose from water outlet. Disconnect ground strap connectors. 2. Remove engine moving control rod and engine mounting bracket No. 2 (right side), located near timing belt cover. Remove generator-to-engine bracket for access to timing belt covers. 3. Using Pulley Holder (09213-54015) or equivalent and Handle (09330-00021) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove No. 1 and No. 2 timing belt covers and gaskets. See Fig. 1 . Remove transverse engine mounting bracket from front of engine. Note direction of timing belt guide installation for reassembly reference. Remove timing belt guide. 4. Temporarily install crankshaft pulley bolt and washer in crankshaft. Using crankshaft pulley bolt, rotate crankshaft clockwise until timing mark on crankshaft sprocket aligns with timing mark on oil pump body. See Fig. 2 . 5. Ensure timing marks on camshaft sprockets are aligned with timing mark on No. 3 timing belt cover. See Fig. 2 . If timing marks are not aligned, rotate crankshaft clockwise one full revolution (360 degrees). Remove crankshaft pulley bolt. 6. If reusing old belt, ensure there are 3 installation marks and front arrow marked on belt. See Fig. 3 . If not, place mating mark on belt where it contacts the crankshaft and camshaft sprockets. Also, mark belt with arrow showing direction of rotation. 7. Alternately loosen 2 bolts, and remove timing belt tensioner and dust boot. DO NOT hold tensioner with push rod facing downward. Remove timing belt in the following sequence: No. 1 idler pulley, right camshaft sprocket (firewall side), No. 2 idler pulley, left camshaft sprocket (front of vehicle side), left camshaft sprocket (front of vehicle side), water pump pulley, then crankshaft sprocket

Related Content:

where is the air flow meter on a kb300 lx pdf, 2003 santa fe 2 7 timing belt marks, thermostat for isuzu kb 300lx, mechanic hours to change 1997 honda accord crankshaft pulley, isuzu kb 300 shifter repairs, how to tighten alternator belt on a toyota 1zr, daewoo lanos sump removal, 2003 lexus 3 0camshaft timing marks diagram, 2003 lexus 3 0camshaft timing marks, 2003 2 4 santa fe out two teeth on intake cam for timing rough idle

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

2005 Chevy Truck Silverado 1500 2WD Blower Motor Resistor Replacement

0

Filed Under (Chevy Manuals) by admin on 29-04-2012

download
Blower Motor Resistor Replacement Notes BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) . 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.

Related Content:

2005 chevy blower motor resistor ground connections, testing mazda 5 for faulty blower moror, resistor sl1, part number 05 silverado blower resistor fix, 07-2012 Tahoe blower motor resistor replacement, fan blower resistor for 1998 buick regal, how to change blower motor 2005 hummer h2, how to rotate resistor in schematics, NISSAN CHANGED BLOWER RESISTOR MAKING NOISE WHEN CRANK, removal/replacement of stepper motor in a 05 tahoe

Toyota Starlet Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 15-01-2012

download
Removal Removal Raise and support front of vehicle. 1. Support engine. 2. Remove: RH front wheel. Inner wing panel. Engine mounting and bracket. Auxiliary drive belt(s). Cylinder head cover. Timing belt upper cover [1] . 3. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure crankshaft pulley timing mark aligned [2] . 4. Check hole in camshaft sprocket aligned with mark on camshaft bearing cap [3] . 5. If not: Turn crankshaft one turn clockwise. 6. Remove: Crankshaft pulley bolt [4] . Use tool Nos.09213-14010 & 09330-00021. Crankshaft pulley [5] . Use tool No.09213-31021. Timing belt lower cover [6] . 7. Temporarily fit crankshaft pulley bolt [4] . 8. Ensure timing marks aligned [3] & [7] . 9. Slacken tensioner bolt [8] . Move tensioner away from belt and lightly tighten bolt. 10. Remove: Timing belt. Tensioner pulley and spring [9] & [10] . 11. Installation Installation Check tensioner pulley for smooth operation [9] . 1. Check free length of tensioner spring is 38,4 mm [10] . 2. Fit tensioner and spring. Ensure spring is connected correctly. 3. Push tensioner to left and lightly tighten bolt [8] . 4. Ensure timing marks aligned [3] & [7] . 5. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 6. Slacken tensioner bolt [8] . 7. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [3] & [7] . 8. If not: Repeat installation and tensioning procedures. 9. Tighten tensioner bolt [8] . Tightening torque: 19 Nm. 10. Remove crankshaft pulley bolt [4] . 11. Install: Timing belt lower cover [6] . Crankshaft pulley [5] . 12. Install components in reverse order of removal. 13. Tighten crankshaft pulley bolt [4] . Tightening torque: 152 Nm. Use tool Nos.09213-14010 & 09330-00021. 14.

Related Content:

1999 toyota camry crankshaft bolt direction, can I replace the camshaft pulley bolt on a 2004 Kia Sorento here at home?

Related Content:

2002 honda accord 2 3 timing belt tension adjustment, toyota2y engine only starts when rocker shaft has been loosened, 2005 audi 3 2 tdc diagram, 2006 kia sorento camshaft pulley repair manual pdf, how to replace a tensioner pulley on a 2006 mazda 5, 2003 buick lasabre serpentine belt idler pulley torque spec, mazda 6 crankshaft tool, pulley configuration 2001 buick lesabre, Residue from serpentine bolt on smooth pulleys, lincoln ls crank pulley diagram