hubsan x4 107c trouble shooting

You search PDF repair manual about hubsan x4 107c trouble shooting, if there are search results will appear below. If search results do not exist, please search by others keyword.



  hubsan x4 107c trouble shooting Direct Download speed 5432 Kb/s

  hubsan x4 107c trouble shooting Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra, silverado motor mount replace

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Related Content:

how do i install ignition switch on 1996 chevy pickup, how to replace a 1990 Toyota Corolla Ignition switch, g6 testing key switch, what causes 2005 toyota sienna starter relay to burn out, 2007 chevy silverado brake switch installation, no power between starter and ignition uplander, ignition switch wiring diagram 2006 chevrolet uplander, ignition switch removal on 2003 buick century, how toremuve thh ignition key on chrysler 2002 concord LX1 or baypass, how to take ignition switch out of kia sorento

1997-2001 FORD EXPEDITION ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE

0

Filed Under (Ford Manuals) by admin on 26-01-2012

download
SUSPENSION, AIR SUSPENSION DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 RIDE HEIGHT RESET PROCEDURE ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE SERVICE PROCEDURE AIR SUSPENSION DTC’S THAT ARE PRESENT NOTE BEFORE ADDRESSING B2140/C2140. DURING PDI (PRE-DELIVERY INSPECTION) IF WARNING “CK SUSP” LIGHT IS ON, PRIOR TO SENDING WARNING: BEFORE REPLACING ANY AIR TO SERVICE, VERIFY SWITCH IN UPPER RIGHT SUSPENSION COMPONENTS, HOISTING, KICK PANEL IS ON. THIS SWITCH IS TURNED JACKING, OR TOWING, DISCONNECT POWER OFF DURING VEHICLE SHIPMENT TO PREVENT TO THE SYSTEM BY TURNING OFF THE AIR MODULE FROM SEEKING TRIM HEIGHT WHILE SUSPENSION SWITCH LOCATED IN THE RIGHT SECURED DOWN FOR TRANSPORT. KICK PANEL AREA TO PREVENT VEHICLE NOTE DAMAGE OR PERSONAL INJURY. AN INADVERTENT B2140 OR C2140 MAY RAS ONLY – CLEAR 2140 RESULT IF A PARAMETER RESET (CLEAR RIDE HEIGHT) IS SELECTED UNDER NGS ACTIVE NOTE COMMANDS, THEN CANCELLED OUT. EVEN RAS (4X2) EQUIPPED VEHICLES REQUIRE STORING RIDE HEIGHT AND NOTE TOGGLING FRONT TO “ON” TO CLEAR A CK THE AIR SUSPENSION CONTROL MODULE SUSP LIGHT/2140 CODE. THIS ALLOWS THE PART NUMBER IS INTERCHANGEABLE MODULE TO STORE THE VOLTAGE WITH NO BETWEEN THE REAR AIR SUSPENSION (RAS) FRONT HEIGHT SENSOR PRESENT, AND MUST AND 4-WHEEL AIR SUSPENSION (4WAS) BE DONE EVEN WITH CONVENTIONAL (STEEL SYSTEMS, BUT ONCE THE MODULE IS COIL) FRONT SUSPENSION. INSTALLED, THE VEHICLE WILL THEN DETERMINE WHETHER VEHICLE IS 4X2 (RAS)

Related Content:

conventional colored front end 2wd suspension diagrams for ford f150 xlt 2001, 99 yukon front suspension diagram, diagram of 2001 chevy blazer front axle, diagram of chrysler 300 front suspension, diagram of front suspension on 2000 ZR2, dodge ram 2500 front suspension diagram 2002, front solenoid code for acura integra 97, hhr rear suspension diagram, How do I replace the spindle bearing on a 1991 Jaguar XJ6, how do you clear DTC codes on 1994 saturn sl1

2005 Ford F-Super Duty 250-550 Auxiliary Brake System/ Trailer Brake Control (TBC) Module Repair Manual

0

Filed Under (Ford Manuals) by admin on 14-06-2012

download
connected to the vehicle, the TBC module will enter a “sleep mode” but still continue to send a PWM voltage signal to the trailer tow connector every 4 seconds to detect when a trailer is connected. When the ignition key is in the RUN position and the module is in sleep mode, pressing a gain button or sliding the manual switch will cause the module to “wake up”. If a trailer is not connected to the vehicle, the display should prove out for 3 seconds, then the trailer icon should illuminate red and the IC message center should display TRAILER DISCONNECTED or CHECK TRAILER. If a trailer is connected to the vehicle, the display should prove out for 3 seconds and then the trailer icon should illuminate green. Inspection and Verification NOTE: A trailer brake emulator tool is available to verify that the TBC module and vehicle wiring are functioning correctly. 1. Verify the TBC system is correctly installed by checking that the vehicle is equipped with a brake pressure transducer on the master cylinder. If the brake pressure transducer is not present, then the TBC system has been erroneously installed. 2. Verify the customer concern. 3. NOTE: The TBC does not function with electric-over-hydraulic or surge trailer brake types. Verify that the trailer brakes are electric-actuated drum type brakes. 4. Verify the stoplamps operate correctly by applying and releasing the brake pedal with the ignition switch in the OFF position and the trailer disconnected. If the stoplamps do not operate correctly, refer to Section 417-01 . If the stoplamps operate correctly, proceed to the next step. 5. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Chart 6. If the cause is not visually evident, connect the scan tool to the data link connector (DLC) and select the vehicle to be tested from the scan tool menu. If the scan tool does not communicate with the vehicle: * check that the program card is correctly installed. * check the connections to the vehicle. * check the ignition switch position. 7. If the scan tool still does not communicate with the vehicle, refer to the scan tool operating manual. 8. Carry out the scan tool data link test. If the scan tool responds with: * CAN, ISO, or UBP circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 . * No response/not equipped for the TBC, GO to Pinpoint Test A . * System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out self-test diagnostics for the TBC and the antilock brake system (ABS) module. 9. If the DTCs retrieved are related to the concern, go to the Trailer Brake Control (TBC) module Diagnostic Trouble Code (DTC) Chart or Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Chart to continue diagnosis. 10. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnosis. NOTE: Always retrieve the continuous DTCs after running the self-test.

Related Content:

2005 f150 security module, 2007 ford f250 tbc fault, 2008 Ford sd brake pressure transducer, an i program a ford abs module, ford tbc fault, programming abs module ford, tbc falt on 2005 ford f350

2001 Dodge Dakota CENTRAL TIMER MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 28-06-2012

download
1. Connect scan tool to Data Link Connector (DLC), under lower left side of instrument panel. Turn ignition on. Using scan tool, attempt to communicate with Air Bag Control Module (ACM) and Controller Antilock Brake (CAB) module. If scan tool is able to identify or communicate with ACM and CAB, go to next step. If scan tool is not able to identify or communicate with ACM and/or CAB, perform appropriate DTC or symptom test. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION and SYMPTOM IDENTIFICATION tables under SELF-DIAGNOSTIC SYSTEM. 2. Turn ignition off. Disconnect Gray 26-pin Central Timer Module (CTM) connector C1. CTM is located behind left side kick panel. Ensure interior lights are off. Using DVOM, measure resistance between ground and Gray 26-pin CTM connector C1 terminals No. 1 and 16 (Black/Light Green wires) and No. 2 (Black wire). See Fig. 5 . If resistance is 10 ohms or less on each ground circuit, go to next step. If resistance is more than 10 ohms on any ground circuit, check for an open between appropriate CTM connector terminal and ground. See GROUND DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 3. Disconnect Gray 12-pin CTM connector C3. Using test light connected to ground, probe Gray 12-pin CTM connector C3 terminals No. 1 (Red/Tan wire) and No. 6 (Red/Light Green wire). See Fig. 8 . If test light illuminates on both circuits, go to next step. If test light does not illuminate on both circuits, check for open in appropriate circuit between power distribution center and CTM. See POWER DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 4. Turn ignition on. Using scan tool, ensure there is PCI BUS communication with other modules (besides the ACM and CAB). If scan tool is able to identify or communicate with all modules, go to next step. If scan tool is not able to identify or communicate with all modules, refer to appropriate communications symptom for diagnosis. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION table under SELF-DIAGNOSTIC SYSTEM. 5. Connect Scope Input Cable (CH7058) to channel one connector on scan tool. Connect Cable-To-Probe Adapter (CH7062) and Black and Red test probes to scope input cable. Connect Black test probe to ground. Connect Red test probe to PCI BUS circuit at Gray 26-pin CTM connector C1 terminal No. 10 (Violet/Yellow wire). 6. Using scan tool, select PEP MODULE TOOLS, LAB SCOPE, LIVE DATA. Select 12 VOLT SQUARE WAVE. Press F2 for SCOPE. Press F2 and use DOWN arrow to set voltage scale to 20 volts. Press F2 again when complete. Turn ignition on. If reading on lab scope toggles between zero and 7.5 volts, go to next step. If reading on lab scope does not toggle between zero and 7.5 volts, repair open in PCI BUS circuit (Violet/Yellow wire). 7. Replace CTM. See CENTRAL TIMER MODULE under REMOVAL & INSTALLATION

Related Content:

2001 dodge ram central timer module location, can you repair a central timer unit?, 2000 mazda mpv p0755 code Broken wire, UT Scan Plan, scan tool will not communicate for air bag codes, programing a CTM, ct 20 turbo diagram, control time module rear bumper for 2002 dodge dakota, central timer module 2003 Dodge Dakota replacement, central time moduale dodge durango 2001

1990-1994 Lexus LS400 How to Check Air Conditioning Diagnostic

0

Filed Under (Lexus Manuals) by admin on 15-06-2012

download
1) First perform an indicator check to see if all the lights are working properly. Press and hold the AUTO & REC buttons and then start the car. Release the buttons after the car has started. All the lights should light up and go off 4 times in a row at one second intervals. You should also hear a beep as the indicators light up. After the indicators blink 4 times you’re in A/C diagnostic mode. 2) Read the code displayed on the LCD. Here you see a code 21; this can happen if you’re not in light because it refers to the solar sensor. 3) Here’s what normal will look like, code 00. When the codes are displayed they blink and beep. Here are all the codes that can be displayed……… Code – Meaning 00 – Normal 11 – Open or short in room temperature sensor circuit. 12 – Open or short in ambient temperature sensor circuit. 13 – Open or short in evaporator temperature sensor circuit. 14 – Open or short in water temperature sensor circuit. 21* – Open or short in solar sensor circuit. 22* – Compressor motor locked. And/or, open or short in compressor lock sensor circuit. 31 – Open or short in air mix damper position sensor circuit. 32 – Open or short in air inlet damper position sensor circuit. 33 – Open in air mix damper position sensor circuit. Or, open or short in air mix servomotor circuit. Or, air mix servomotor locked. 34 – Open in air inlet damper position sensor circuit. Or, open or short in air inlet sensor servomotor circuit. Or, air inlet servomotor locked. * – These are detected only when they are the current troubles. Other codes detect both current trouble (beep) and past trouble (no beep). A/C indicator light blinks – This means your A/C compressor is locked. It’s happened to me before and I needed a new (rebuilt) compressor installed. 4) Once you’ve read any codes you can proceed to performing an actuator check by pressing the REC button. This will start a check of different combinations for the system starting with code 20 and moving up to 29. To cancel this or the previous diagnostic modes simply press the OFF button.

Related Content:

gm b0100 code short ind squib circurt, gmc acadia b0100 2008, injection actuation pressure sensor circuit, what does b0100 short in d squib curquit mean

Toyota V6 Adapter Plate Installation Manual

0

Filed Under (Toyota Manuals) by admin on 30-03-2012

download
Apply silicone to face of single or dual transfer case assembly. Install adapter plate on face of transfer case, using 4 M10-1.25×35 bolts (provided). We recommend applying blue LocTite® to threads before installation. Torque four plate bolts to 30 ft. lbs. Step 2 Install M-10-1.25×30 allen head bolt using blue Loc- Tite® torque to 30 ft. lbs. Step 3 Remove rear transmission seal using a seal remover or claw hammer. Step 4 Step 5 Install M-10-1.25x 35 bolt using blue LocTite® torque to 30 ft. lbs. Using degreaser, clean the rear transmission seal sur- face. Step 6
Ensure two dowels are in place in the transmission. If dowels are in the transfer case move them to the trans- mission. Step 8 Step 11: Apply silicone to rear face of transmission Slide coupler into place on the back of the transmis- sion. Step 7 Step 9 Step 10 Apply silicon to smaller end of seal adapter Install Seal Adapter into rear of transmission. Gently seat seal adapter into place using rubber mallet Step 11 After Assembling Adapter Plate & T/Case(s): Install replacement v6 dual transfer case crossmember Reconnect 4 wheel drive indicator (This may require cutting and splicing connector from original case) 1988-1991 Application, reconnect speedometer cable (Use speedometer extension cable for dual case applications) 1992-1995 Application will need a replacement VSS for the transfer case Reattach front and rear drive shafts (drive shaft lengths may need to be changed) Fill transfer case with 90W GL5 gear oil, check gear oil level in transmission Reinstall transfer case shifter and boot Drain and replace transfer case oil after first 1,000 miles and every 30,000 thereafter Full synthetic gear oil may be used. Step 12 Using 6 of the 9 stock bolts, 1 allen head bolt and 2 M10-1.25×35 bolts, attach transfer case to transmission. Use blue LocTite® on all bolts. Tighten bolts to 30 ft. lbs. The second allen head bolt should be installed in position shown on the upper right (passenger) side. Step 13 These instructions are designed as a general installation guide. Installation of many Trail-Gear Products require specialized skills such as metal fabrication, welding and mechanical trouble shooting. If you have any questions or are unsure about how to proceed, please contact our shop at 559-252-4950 or seek help from a competent fabricator. Using fabrication tools such as welders, torches and grinders can cause serious bodily harm and death. Please operate equipment carefully and observe proper safety procedures. Rock crawling and off-road driving are inherently dangerous activities. Some modifications will adversely affect the on-road handling characteristics of your vehicle. All products sold by Trail-Gear Inc are sold for off road use only. Any other use or application is the responsibility of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may under certain circumstances void your original dealer warranty. Modification of your vehicle may create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or death. Buyers and users of these products hereby expressly assume all risks associated with any such modifications and use.

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose Service Procedure

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud. 1. Replace linkage arms on all three (3) sensor assemblies following Workshop Manual (WSM), Section 204-05. 2. Discard the old linkage arms. NOTE IF THE SENSOR ASSEMBLY NEEDS TO BE REPLACED FOR ANY DAMAGE/FAILURE OTHER THAN THE ONE DESCRIBED IN THIS TSB, THE REPLACEMENT ASSEMBLY IS SUPPLIED WITH A NEW STYLE LINKAGE ARM, SO THERE IS NO NEED TO ORDER ADDITIONAL LINKAGES FOR THE SERVICE REPAIR. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage OPERATION DESCRIPTION TIME 061510A 2003-2006 0.4 Hr. Expedition/Navigator: Replace The Three Linkage Arms, Includes Time To Check Diagnostic Trouble Codes (Do Not Use With 5300A, 5300A7, 5300A8) DEALER CODING CONDITION BASIC PART NO. CODE 5A967

Related Content:

2003 ford explorer front endSUSPENSION ASSEMBLY chematics, 2006 f150 front suspension diagram, air suspension sensor ford, change front struts 2006 gs300, how to repair 03 explorer front control arm, schematic for 2003 lincoln town suspension

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

0

Filed Under (Chevrolet Manuals) by admin on 07-05-2012

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

Related Content:

acura mdx check charging system, how to drain the air conditioner on a 2003 jetta, where do you recharge ac on 1996 buick regal, 2007 chevy trailblazer code c0161, troubleshooting P069E, tranny fluid location 2010 santa fe, 4M51Engine valve clearance, free PDF repair manuals 1999 chevy silverado, reset procedure for ride heighth 04 navigator, chevy impala air conditioner flapper doesnt turn off

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual