hyundai b1382 fixed

You search PDF repair manual about hyundai b1382 fixed, if there are search results will appear below. If search results do not exist, please search by others keyword.



  hyundai b1382 fixed Direct Download speed 5432 Kb/s

  hyundai b1382 fixed Full Version speed 8172 Kb/s



1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

0

Filed Under (Chevrolet Manuals) by admin on 07-05-2012

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

Related Content:

acura mdx check charging system, 2006Chevyimpala4t65Echeckballlocations, how to drain the air conditioner on a 2003 jetta, manual seting sistem injection pord ranger, test circuit driver injector toyota hilux 2010 3 0 wiring diagram in pdf free, tranny fluid location 2010 santa fe, troubleshooting P069E, 4r100 rear carrier assembly colorado springs, chevy impala air conditioner flapper doesnt turn off, 2007 chevy trailblazer code c0161

2001 Hyundai Sonata Air Bag Restraint Systems Repair Manual

0

Filed Under (Hyundai Manuals) by admin on 21-05-2011

download
Scan Tool Display B1111 Battery voltage high B1112 Battery voltage low B1346 Driver-side air bag resistance high B1347 Driver-side air bag resistance low B1348 Driver-side air bag short to ground B1349 Driver-side air bag short to battery B1352 Passenger-side air bag resistance high B1353 Passenger-side air bag resistance low B1354 Passenger-side air bag short to ground B1355 Passenger-side air bag short to battery B1361 Driver-side seat belt pretensioner resistance high B1362 Driver-side seat belt pretensioner resistance low B1363 Driver-side seat belt pretensioner short to ground B1364 Driver-side seat belt pretensioner short to battery B1367 Passenger-side seat belt pretensioner resistance high B1368 Passenger-side seat belt pretensioner resistance low B1369 Passenger-side seat belt pretensioner short to ground B1370 Passenger-side seat belt pretensioner short to battery B1378 Driver side impact air bag resistance high B1379 Driver side impact air bag resistance low B1380 Driver side impact air bag short to ground B1381 Driver side impact air bag short to battery B1382 Passenger side impact air bag resistance high B1383 Passenger side impact air bag resistance low B1384 Passenger side impact air bag short to ground B1385 Passenger side impact air bag short to battery B1400 Satellite left side defective B1401 Satellite left side short to ground B1402 Satellite left side short to battery B1403 Satellite right side defective B1404 Satellite right side short to ground B1405 Satellite right side short to battery B1406 PPD defective B1407 PPD communication error B1408 Satellite left communication error B1409 Satellite right communication error B1620 Internal fault B1650 SRSCM crash recorded (replace SCRSM) B1651 Crash recorded driver-side air bag

Related Content:

trouble shooting s10 air bag, 2005 gmc sierra service airbag, 05 caddilac escalade service airbag light, service air bag in where is the fuel filter on a 2005 gmc sierra, prius air bag removal, owners manual for fire stone airbags, measure battery internal resistance manual, igt telltale battery, ford mondeo srs fault code b0001, evap solenoid 2010 silverado test

2001 Hyundai Accent Difficulty filling the gas tank/ The pump keeps clicking off

0

Filed Under (Hyundai Manuals) by admin on 15-04-2012

download
Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted. Potential Causes: Charcoal Canister Liquid Vapor Separator Vapor Line Tech Tips: Fuel vapors are directed to the canister from the ORVR fill vent valve in the gas tank through the liquid vapor separator and to the canister. The metal tube that loops up by the filler neck is part of the vapor line to the canister. Diagnostic Codes: None

Related Content:

location of the fuel vapor canister on 2007 pacifica, 02 hyundai accent disconnecting vapor canister, how to install vapor canister on hyundai sonata, evaporative charcoal how to change fuel filter on 2002 kia sportage, replace charcoal canister in kia rio 2002 where is located has a code p1166, replace EVAP canister 2007 pacifica, symptoms of a clogged evap canister ford, signs of a bad charcoal canister, where is fuel vapor canister on 2007 pacifica, what is located in the trunk of a 2005 buick lesaber

2005 Hyundai Truck Santa Fe TRANSAXLE/ ATA SOLENOID DIAGNOSTIC REPAIR MANUAL

0

Filed Under (Hyundai Manuals) by admin on 11-06-2012

download
Subject: ATA SOLENOID DIAGNOSTIC CODES P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765, P0770 This TSB supersedes TSB # 05-40-006 to include DTC descriptions in Step 10. DESCRIPTION: Incorrect operation of the transaxle solenoids may result in the following three symptoms: REPAIR PROCEDURE: 1. Check Engine Light illuminated 2. Transaxle held in 3rd gear “Fail-safe” 3. Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765 or P0770 set. NOTE: Do NOT replace the transaxle for solenoid codes listed as open/short. Instead, follow the repair procedure shown below. 1. Using a Hi-Scan Pro, check for DTC in both the “Engine” and “Automatic Transaxle” menus. Record the DTC and description. 2. From the Hi-Scan Pro, select: ^”Hyundai Diagnosis” menu ^”Vehicle ^”Auto Transaxle” menu ^”Actuation Test” ^Press the F1 button (STRI) and test the LR, UD, 2ND, OD, DCC and FSV solenoid (if applicable). Monitor the Hi-Scan and listen for a solenoid sound from the engine compartment. ^If Hi-Scan shows: ^”TEST FAILURE” and no solenoid sound is heard, go to Step 3. ^”COMPLETED” and solenoid sound is heard, the wiring between the PCM/TCM has no open or short circuits. Go to Step 5. 3. Visually check the wiring harness between the TCM and transaxle for a damaged wire or a short circuit to ground. Disconnect the connectors to the solenoids at the transaxle and the PCM/TCM and check for a bent pin or a pin not fully inserted into the connector. If so, repair or replace the ECM control harness, P/N 914XX-XXXXX 4. Check the harness inside the transaxle oil pan for a short circuit to ground. Replace the harness if damage is found or if three or more solenoid DTCs are found in Step 1. (Refer to TSB # 04-40-015 for instructions). Zoom Sized for Print 5. Refer to the DTC recorded in Step 1 and follow the repair procedure shown. SOLENOID REPLACEMENT: 6. Remove the battery. 7. Drain the radiator. Remove the lower radiator hose from the radiator. 8. Drain the ATF. 9. Remove the valve body cover from the transaxle

Related Content:

locatiom of gasoline solonoid in tucson 2005, 2005 hyundau sante fe shop manuel free, tucson 2005 gas solenoud, 2005 hyundai santa fe repair manual pdf, starter solenoid causing engine misfire on vortec, p0765 kia sedona hyundai entourage, p0765 kia sedona, p0741 code chevy cobalt, p0741 06 mazda tribute tsb, mazda tribute 2003 engine service pdf

2001 Hyundai Accent 1.5L Difficulty filling the gas tank The pump keeps clicking off Repair Manual

0

Filed Under (Hyundai Manuals) by admin on 08-05-2012

download
Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted. Potential Causes: Charcoal Canister Liquid Vapor Separator Vapor Line Tech Tips: Fuel vapors are directed to the canister from the ORVR fill vent valve in the gas tank through the liquid vapor separator and to the canister. The metal tube that loops up by the filler neck is part of the vapor line to the canister

2004-2005 FORD F-150 FRONT BRAKE ROUGHNESS/ SHUDDER WHILE BRAKING REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 10-06-2012

download
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.

Related Content:

2004 dodge dakota repair manual free download, 2004 Cavalier Repair Manual PDF, change rotors 94 explorer, change rotors on 94 explorer 4x4, copy of 2004 chevy truck mannual, fender passport p 150 service manual, Ford tsb 14-0076, honda pilot 2004 repair manual, how to replace rotors on 2005 f250, MINN ROTOR THICKNESS 04 SEBRING

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 10-05-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

Related Content:

1997 saturn manifold repair, 2000 lexus es 300 gear sprocket, 2007 SATURN RELAY 3 9 V6 TIMING CHAIN/ MAGNETIC SPROCKET

1995 Nissan-Datsun Maxim Water Pump Service and Repair REMOVAL AND INSTALLATION

0

Filed Under (Nissan Manuals) by admin on 03-06-2011

download
1.Drain coolant from drain plugs on radiator and both sides of cylinder block. 2.Remove drain plug on cylinder block. 3.Remove right side engine mounting, mounting bracket and nuts. 4.Remove drive belts and idler pulley bracket. 5.Remove chain tensioner cover and water pump cover. 6.Pushing timing chain tensioner sleeve, apply a stopper pin so it does not return. Then remove the chain tensioner assembly. 7.Remove the 3 water pump fixing bolts. Secure a gap between water pump gear and timing chain, by turning crankshaft pulley 2O° backwards. 8.Put M8 bolts to two M8-threaded holes out of 3 water pump fixing bolt holes 9.Tighten M8 bolts by turning half turn alternately until they reach timing chain rear case. In order to prevent damages to water pump or timing chain rear case, do not tighten one bolt continuously. Always turn each bolt half turn each time. 10.Lift up water pump and remove it. When lifting up water pump, do not allow water pump gear to hit timing chain. INSPECTION 1.Check for badly rusted or corroded body assembly. 2.Check for rough operation due to excessive end play. INSTALLATION 1.Before installing, remove all traces of liquid gasket from mating surface of water pump cover and chain tensioner cover using a scraper. Also remove traces of liquid gasket from mating surface of front cover. 2.Apply a continuous bead of liquid gasket to mating surface of chain tensioner cover and water pump cover. 3.Return the crankshaft pulley to its original position by turning it 2O° forward. 4.Install timing chain tensioner, then remove the stopper pin After installing the tensioner, race the engine at about 3,000 rpm under no load to purge air from the high-pressure chamber. The engine may produce a rattling noise. This indicates that air still remains in the chamber and is not a matter of concern. 5.Install drain plug on cylinder block. 6.Reinstall any parts removed in reverse order of removal

2001 Hyundai Accent GS Sedan Transmission Speed Sensor Service Procedure

0

Filed Under (Hyundai Manuals) by admin on 26-05-2011

download
PULSE GENERATOR-B INSPECTION PROCEDURE: 1. Open and secure the hood. 2. Remove the resonator. 3. Locate the pulse generator under the battery tray. Disconnect the pulse generator connector (blue) and remove the pulse generator male connector (black) from the bracket. 4. Using an ohmmeter, check the resistance between terminal No. 3 and No. 4 in the disconnected pulse generator male connector (black color). Resistance value: 215-275W (at 20°C or 68°F) If the resistance is lower or higher than the specification, replace the pulse generator (P/N 45955-22700). If the resistance is within specification go to Step 5. 5. Clean both ends of the disconnected pulse generator connectors with aerosol electrical contact cleaner. 6. Apply contact grease (P/N 00305-F0000-39, NYOGEL 760G), into all four terminal openings of the blue female connector until each terminal opening is completely filled with grease. 7. Reconnect the pulse generator connectors and reattach the connector to the bracket. Reinstall all removed components in the reverse order of removal. TCM SPECIFICATIONS CAUTIONS BEFORE REPROGRAMMING 1. Conduct reprogramming with the ignition key in the “ON” position. 2. Be careful not to disconnect any cables connected to the vehicle or Hi-Scan Pro during reprogramming. 3. Do not start the engine or turn the ignition key off during reprogramming. WARNING: If reprogramming is interrupted, the manual update procedure must be used. 4. When the reprogramming is completed, turn off the ignition key for 20 seconds before starting the engine. TCM REPROGRAMMING PROCEDURE: 1. Insert the 16 MB reprogramming card into the top slot of the Hi-Scan Pro. 2. Connect the reprogramming adapter to the Hi-Scan Pro. 3. Connect the white reprogramming connector (2 pin or 10 pin) to the reprogramming adapter. NOTE: Use the correct connector: ^2000-01 Accent: White 2-pin connector. ^2002 Accent: White 10-pin connector 4. Connect power to the Hi-Scan Pro from the cigarette power adapter. 5. Insert the power cable from the reprogramming adapter into the cigarette power adapter.

Related Content:

01 accent pulse generator, Powermax Generator Parts Book, pulse generator in transmission, repair manual duromax 4400 generator, titan generator parts lookup, yhs-att_001

2003-2008 Honda Pilot FWD/4WD 2”Front/2” Rear Installation Instructions

0

Filed Under (Honda Manuals) by admin on 20-05-2014

download
1. Check all fasteners for proper torque. Check to ensure for adequate clearance between all rotating, mobile, fixed, and heated members. Verify clearance between exhaust and brake lines, fuel lines, fuel tank, floor boards and wiring harness. Check steering gear for clearance. Test and inspect brake system.
2. Perform steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating,
mobile or heated members. Inspect rear brake hoses at full extension for adequate slack. Failure to perform
hose check/ replacement may result in component failure. Longer replacement hoses, if needed can be pur-
chased from a local parts supplier.
3. Headlight adjustment is highly recommended.
4. Re-torque all fasteners after 500 miles. Always inspect fasteners and components during routine servicing.

Related Content:

nissan ka20 engine manual free, honda Pilot 2011 service code B136, pdfrepairmanual com/ /fuso 6m70 eng, quicksilver 809621 pdf, quicksilver 809621, how to install by pass hose on explorer sport, ax4n e ndplay adjustment procedures, 1989 Dodge dakota ignition wiring, measure vacuum at actuator on ford f150 equals zero but when running engine it stays intwo wheel, 4af fuel intake repairs

Related Content:

acura mdx check charging system, 2006Chevyimpala4t65Echeckballlocations, how to drain the air conditioner on a 2003 jetta, manual seting sistem injection pord ranger, test circuit driver injector toyota hilux 2010 3 0 wiring diagram in pdf free, tranny fluid location 2010 santa fe, troubleshooting P069E, 4r100 rear carrier assembly colorado springs, chevy impala air conditioner flapper doesnt turn off, 2007 chevy trailblazer code c0161