installing heater core on a 2000 chevy blazer

You search PDF repair manual about installing heater core on a 2000 chevy blazer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  installing heater core on a 2000 chevy blazer Direct Download speed 5432 Kb/s

  installing heater core on a 2000 chevy blazer Full Version speed 8172 Kb/s



2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

0

Filed Under (Chevrolet Manuals) by admin on 20-05-2011

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, location of mode motor for 99 honda civic lx, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram, Hino 268 2013 fuse box for heater location

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 saturn sl1 owners manual, 2000 buick century service manual free, 560sl repair 1988, 2000 crv P0505, park avenue ac control schematic, 2000 chevrolet suburban haynes, 2000 e450 ford travelmaster motorhome manual, 2000 nissan altima po340

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, how to remove the heater core on 2000 VW Beetle, Redezvous Dash Removal, 2003 mitsubishi eclipse replace evapulator, 2002 silverado remove front driveshaft, 2002 ford taurus evap emission line location, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette, 2004 Buick lesabre inrument cluster removeal

2000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-07-2012

download
Evaporator Core Housing Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screws from the RH fender apron and remove the fender apron. 7. Remove the nuts. 8. Lower the vehicle. 9. Remove the blower motor switch resistor. For additional information, refer to Section 412-04 . 10. Disconnect the connector. 11. Disconnect the evaporator to compressor suction line from the suction accumulator drier. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 12. Disconnect the condenser to evaporator tube from the A/C evaporator core inlet tube. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 13. Remove the nuts and position the purge valve and backet away from the evaporator core housing. 14. Remove the heater hoses from the heater core. 15. Disengage the connectors fom the bracket. 16. Disconnect the connector. 17. Remove the nut and reposition the wire harness away from the evaporator housing. 8 18. Disengage the harness from the bracket. 19. Remove the pin-type retainer and clip and remove the instrument panel lower insulator. 20. Fold back the carpet and remove the screw. 21. Inside the vehicle, remove the screw. 22. Remove the nuts(engine side).

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, Low coolant light olds intrigue, how to check radiator fluid level pontiac grand prix, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, 2002 chevy avalanche instrument cluster wiring, p0446 2002 monte carlo, 2002 mercury sable cooling system, evap sensor on 2002 suburban

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, zimmatic pivot wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, 1996 silverado electrical manual, 97 buick riviera Ignition Switch Diagram

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

Toyota Sequoia SR5 2001-2006, Toyota Tundra 2000-2006, Toyota Tundra D-Cab 2005-2006 Signal Mirror Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
1. Open the driver side door and lower the window. 2. Remove the door panel, kick panel, and plastic trim piece along the bottom of the door frame. 3. Disconnect the mirror wire harness. Remove the three mirror mounting nuts and remove the mirror housing from the vehicle. 1 2 3 Mirror Replacement – 2 – 4 There is a plug seated in a socket in the center of the mirror that holds the mirror in the mirror housing. Lift up the inboard edge of the mirror. Use a small pry bar and pry up around the center of the mirror until the plug unseats from the socket. 5 There are two drive pins on the bottom and outboard sides of the mirror. Hold the top of the mirror away from the mirror housing and pry away the bottom drive pin from the back of the mirror. 6 Hold the inboard side of the mirror away from the mirror housing and pry away the outboard drive pin from the back of the mirror. IF heated, disconnect OE heater wire from heater terminals. Note: During the removal of the original mirror, if motor pins stay attached to the back plate, use “V” end in small pry bar or needle nose pliers to disengage pins from back plate. Set the mirror aside. 7 8 Using the shorter of the two harnesses from the kit, tape the end without the mating connector to the end of the gopher wire. Remove the foam insulation from the mirror housing sail. Starting from the inside of the mirror housing, guide a piece of gopher wire down alongside the existing factory wire harness and out of the bottom of the mirror housing sail. 9 Pull the gopher wire and wire harness through the mirror housing until about 4 inches of wire remain inside the mirror housing.
13 Tuck the wire harness behind the Signal® mirror. Insert the other drive pin into the outboard pin socket (socket closest to the optic module). Align the socket in the center of the Signal® mirror over the plug on the center of the mirror mount. Align drive pins to its mating slots on the motor mount and vice-versa. Anti-vibration tab should be tucked inside housing. 14 Use the palm of your hand and firmly press down on lower portion (marked boundaries) of the Signal® mirror until it snaps into position. Press down carefully on the mirror outboard edge to engage outboard drive pin into mirror mount socket. 15 Press mirror down carefully on the lower edge to engage the lower drive pin into motor mount. Remount mirror to door, then use Electronic Hand Control to relocate mirror position. Gently clean any finger mark/dirt away from mirror using paper towel and glass cleaner. 10 Guide the Signal® mirror harness along the existing path of the factory wire harness and through the foam insulation. Remove any slack in the wire. Reposition the foam insulation on the mirror housing sail. 11 Connect the Signal® mirror mating connector to the Signal ® mirror harness. If heated , reconnect the heater wires to the heater terminals on the back of the new Signal® mirror. NOTE: There is no polarity so the wires may be interchanged. Disregard heater connections on vehicles not equipped with outside heated mirrors. 12 The drive pins must be aligned before installing the Signal® mirror. If needed, insert a drive pin into the lower socket on the mirror mount. Align the nubs on the lower drive pin so it points to the round plug in the center of the mirror mount.

Related Content:

how to access to wiring harness for radio on 2006 Buick Lucerne, 2006 malibu door wiring diagram, Saturn ION-2 2 2 L4 GAS Wiring Diagram, Repairing a ford F-150 side mirror 2011, repair link pins on Tundra 2000, OnStar FMV Wiring Instructions, mirror glass removal f150, how to replace heated power mirror glass 2004 ford f150, how to remove a side mirror from a 1994 ford f150 truck, 2000 mercury cougar drivers side mirror free replacement instructions

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre