Skip to content

intake manifold torque specs for 2004 kia sedona

You search PDF repair manual about intake manifold torque specs for 2004 kia sedona, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

1995-2004 Toyota Tacoma Helix Power Tower PLUS Installation Manual

download
1. Remove the air cleaner duct from throttle body. 2. Unbolt the throttle linkage from the intake plenum by unbolting the single 12mm-sized bolt. 3. Unbolt the lower vacuum line from intake plenum. Remove the four bolts (some models may have bolt/stud combination, either case they all need to be removed) from the intake manifold. 4. Separate throttle body from the intake plenum and remove the OE gasket. Place the Helix Power Tower PLUS (engraved side towards throttle body) with the new gaskets in between the throttle body and the intake plenum. Secure with the new longer bolts supplied with this kit. On 2003-2004 models you will need to use the longer 8mmx110mm bolts to complete the installation. Torque the assembly to 15 ft/lbs. 5. Install the throttle linkage extender plate to plenum (original stock location) with OE bolt. Please make sure the roll pin of the plate is in locator hole on plenum. Reinstall the throttle linkage to the extender plate and use the supplied hardware to secure it to the new extender plate. Torque both bolts to 10 ft/lb. 6. Install new vacuum line extender (black z-bend bracket) to original location with OE bolt and install vacuum line bracket to this extender with the supplied hardware. Torque both bolts to 8 ft/lb. (Note: it may be necessary to lengthen the linkage cable and vacuum line from the intake plenum anchor points) 7. Reinstall the air cleaner duct to the throttle body.

Chrysler V8 DUAL QUAD INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
PREP AND TUNING FOR POWER: NOTE: This manifold will produce optimum power and drivability when used with #1405 carburetors. Please refer to Edelbrock Performer Series Carburetor Owner’s Manual for tuning procedures. 1. Edelbrock has found, while dyno testing on a Performer level engine at our location, the best calibration to be: Metering Rods – .070″ x .047″ (stock 1405), Primary Jets – .098″ (provided with intake manifold), and Secondary Jets – .086″ (provided with intake manifold). This will vary according to engine build and atmospheric conditions. Use it as a starting point. However, if used for racing or marine installation, further tuning may be necessary. 2. Aftermarket distributor curve kits may be used with this intake manifold. A basic ignition curve of 12° to 14° initial and a total of 36° to 38° advance is a good starting point. 3. Use modified or high performance cylinder heads such as our Performer RPM. 4. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this condition occur, recalibrate with a richer jet. • CAMSHAFT AND HEADERS: Dual Quad manifolds are compatible with aftermarket camshafts and headers. Header primary tube diameter should be 1-7/8″, depending on the specific engine combination. Edelbrock has developed two camshafts for use with this intake manifold – Performer-Plus #2192 or Performer RPM #7194. Please check the catalog or website for rpm and application guidelines. INSTALLATION 1. Use only recommended intake gaskets set when installing this intake manifold. For ease of installation, we recommend Edelbrock Manifold Bolt and Washer Kit, #8594. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Use a factory style valley pan along with the recommended gaskets. 4. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 5. Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs

Chrysler 413-426 CH- 6 B CHRYSLER 6 -PACK INTAKE MANIFOLD INSTALLATION MANUAL

download
NOTE: Please refer to Edelbrock Performer Series Carburetor Owner’s Manual for detailed tuning procedures. 1. Due to design, the fuel/air mixture and cylinder charging are very efficient with the CH-6B intake manifold. Generally speaking, the stock jetting for the recommended aftermarket carburetors will not need changing. Specific applications may show an increase in performance through further tuning. 2. Aftermarket distributor curve kits may be used with this intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM. 4. The compression ratio should be at least 9.5 to 1 to work properly with Performer RPM camshafts. 5. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this occur, recalibrate with a richer jet INSTALLATION: 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Use a factory style valley pan along with the recommended gaskets. 4. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 5. Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs.

Chevrolet V8 With General Duty Oval Port Cylinder Heads STREET TUNNEL RAM INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
CAMSHAFT AND HEADERS: The Street Tunnel Ram manifold is compatible with aftermarket camshafts and headers. Use Edelbrock Torker-Plus camshaft #5062 for more low RPM torque, or the Edelbrock Performer RPM camshaft #7162 for more high RPM power. Header primary tube diameter should be 1-7/8″. This may vary depending upon your particular engine specifications. PREP AND TUNING FOR POWER: 1. Specific applications may show an increase in performance through additional carburetor tuning. 2. Aftermarket distributor curve kits and aftermarket ignitions may be used with the Street Tunnel Ram intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM, and port match the intake manifold to the heads. 3. The engine’s compression ratio should be at least 9.5:1 to work properly with Torker-Plus or Performer RPM camshafts. INSTALLATION PROCEDURE INTAKE MANIFOLD BASE 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 4. Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼” high bead across each block end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal slippage. 5. Install the intake manifold hold-down bolts. Hand tighten all bolts to approximately 5 ft./lbs. to center the manifold on the engine. WARNING: There is no gasket support for the manifold under the four bolt holes which are numbered 13,14,15, and 16 in Figure 1 below. Damage to the manifold will occur if these four bolts are over tightened. Hand tighten these bolts with a 6″ box-end wrench. DONOT use a torque wrench. 6. Torque all of the remaining manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs. INTAKE MANIFOLD TOP 1. Apply Edelbrock Gasgacinch sealant P/N 9300 to the gasket mating surface and install the gasket and manifold top. 2. Install and tighten the supplied hold down bolts to 15-18 ft./lbs.