intermediate axle shaft bearing kia sedona

You search PDF repair manual about intermediate axle shaft bearing kia sedona, if there are search results will appear below. If search results do not exist, please search by others keyword.



  intermediate axle shaft bearing kia sedona Direct Download speed 5432 Kb/s

  intermediate axle shaft bearing kia sedona Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, size axle nut 2005 explorer, 2005 dodge magnum how to replace rear axle hub, 2002 ford expedition trailing arm torque specs, replace shaft seal in AT 2006 Avalon, remove right side axle on a 2001 toyota sienna

1994 Nissan Maxima SE FWD Axle Shafts Removal And Installation Manual

0

Filed Under (Nissan Manuals) by admin on 21-05-2011

download
FWD AXLE SHAFT Removal 1. Raise and support vehicle. Remove wheel. Remove wheel bearing lock nut from end of drive axle. Remove disc brake caliper and suspend out of way. DO NOT allow caliper to hang by hydraulic hose. 2. Separate tie rod end from steering knuckle. Remove axle shaft from steering knuckle hub using a soft mallet. On models with ball and cage type right axle shaft, remove support bearing retainer-to-block bolts. See Fig. 4 . 3. On all models, pry right axle shaft from transaxle using screwdriver. See Fig. 1 . On M/T models, pry left axle shaft from transaxle using screwdriver. On A/T models, insert screwdriver through right axle shaft hole in differential, and drive out left axle shaft. See Fig. 2 1. Place axle shaft in soft-jawed vise with inner joint facing up. Remove boot clamps. See Fig. 4 . Mark slide joint housing and inner race in relation to axle shaft for reassembly reference. 2. Remove and discard snap ring “A”. See Fig. 3 and Fig. 4 . Remove slide joint housing. Remove snap ring “C”. Remove cage, inner race and balls as an assembly. Remove snap ring “B”. Cover axle shaft splines with tape. Remove boot. 3. To disassemble support bearing and retainer assembly on right axle shaft, remove dust shield and snap ring “D”. See Fig. 4 . Press axle shaft out of support bearing and retainer assembly. Remove snap ring and dust shield from retainer. Using bearing driver and hammer, drive support bearing out of retainer.

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 25-01-2012

download
Repair Procedure 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. Production Change Information Parts Information Repair Procedure STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 3 of 4 3. Remove the No. 2 steering intermediate shaft assembly. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 7. Install the No. 1 steering column hole cover sub-assembly onto the steering gear with a NEW clamp. Repair Procedure (Continued) B A a No. 2 Steering Intermediate Shaft Intermediate Shaft STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 4 of 4 8. Install the No. 1 steering column hole cover sub-assembly by attaching clip B onto the body and installing the No. 1 hole cover onto the body with clip A. NOTE: Make sure that the lip of the No. 1 hole cover is NOT damaged. 9. Install the No. 2 steering intermediate shaft assembly. A. Align the matchmarks (“a”) on steering intermediate shaft and the steering sliding yoke and temporarily install them with bolt B. Torque: 35 Nm (360 kgfcm, 26 ftlbf) B. Ensure the wheels are straight. C. Install the No. 2 intermediate shaft and the intermediate shaft with bolt A. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 10. Install the column hole cover silencer sheet. A. Install the column hole cover plate with the 2 clips. B. Install the floor carpet. 11. Remove the steering wheel holder from the vehicle. 12. Road test the vehicle to verify the repair and confirm that the steering wheel is centered.

Related Content:

07 ford escape intermediate drive shaftpassenger side, 2003-2011 ford crown vic intermediate steering shaft removal, 3024 CAT Rocker Shaft Assembly, 91 Dakota Intermediate Steering Shaft, 92 Dakota Intermediate Steering Shaft, cruze cam cover crack, steering pitman shaft drawing 91 dodge dakota 2 wheel drive

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 13-11-2011

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

Related Content:

2003 toyota camry 2 4 main crankshaftbearing removal, stearing colium cover removel 2003 buick reagel, Reinstall steering column for 1992 Toyota Camry, kia sorento front drive shaft center bearing removal, kia sorento center support bearing removal, kia sorento 2007 manual driveshaft carrier bearing, jeep upper bearing pulls out, how to remove steering column cover on 1994 mitsubishi gt3000, does the center bearing on a 2007sorento require lubrication, 2007 kia sorento center support bearing

1994 Ford Explorer SPINDLE AND SHAFT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
Removal 1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub. See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION. 2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if equipped) and splash shield. 3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 . 4. Remove left shaft assembly (if required). On all applications, wrap spindle in protective cloth and place second step of spindle in soft-jawed vise. 5. On Explorer and Ranger, remove oil seal using slide hammer and Seal Remover (TOOL-1175-AC). Remove needle bearing from spindle. Press seal from shaft assembly. See Fig. 9 . 6. On Bronco and F150, remove needle bearing and oil seal using slide hammer and Cup Puller (T77F- 1102-A). Press seal from shaft assembly. Installation 1. Clean all dirt and grease from spindle bearing bore. Ensure bearing bore is free of nicks and burrs. On Explorer and Ranger, install seal on shaft assembly using press and Seal Installer (T83T-3132-A). 2. On Bronco and F150, install seal on shaft assembly, with seal lip toward spindle. On right side applications, install rubber boot and NEW keystone clamps on stub shaft. Install right shaft assembly into stub shaft, with stub shaft missing spline aligned with shaft assembly. 3. Ensure splines are fully engaged. Install rubber boot over assembly and tighten keystone clamps. On left axle applications, install shaft assembly through steering knuckle, and engage in splines. 4. Install needle bearing in spindle, with manufacturer identification mark facing away from spindle bore. For bearing installation, use Handle (T80T-4000-W), and Bearing/Seal Installer (T83T-3123-A for Explorer and Ranger; T80T-4000-S for Bronco and F150).

Related Content:

2005 f150 half wrap, how to replace a turbine speed sensor on a 1998 ford explorer, remove shaft 326rx service manual, spindle nut torque 2007 ford 150

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, size axle nut 2005 explorer, 2005 dodge magnum how to replace rear axle hub, 2002 ford expedition trailing arm torque specs, replace shaft seal in AT 2006 Avalon, remove right side axle on a 2001 toyota sienna