Skip to content

isuzu d max radio removal

You search PDF repair manual about isuzu d max radio removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

1998 Ford F 150/250 Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

download
Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. Remove the passenger air bag. For additional information, refer to Section 501-20B . 3. Remove the driver air bag. For additional information, refer to Section 501-20B . 4. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal. Carefully pry to release the (A) clips and remove the (B) steering column opening cover. 5. Position the electrical connector aside. * Release the push clip from the lower instrument panel steering column cover (044F08). 6. Pull to release the three (A) clips and remove the (B) fuse door. 7. Position the hood latch release handle aside. 1. Remove the screws. 2. Position the hood latch release handle aside. 8. Position the parking brake release handle aside. 1. Remove the screws. 2. Position the parking brake release handle aside. 9. If equipped, remove the instrument panel floor duct panel. * Remove the two push clips and release the expander clip. 10. Remove the lower instrument panel steering column cover (04459). 1. Remove the bolts. 2. Remove the lower instrument panel steering column cover. 11. Remove the LH and RH scuff plates. 12. Remove the LH and RH cowl side trim panels. 13. Disconnect the brake pedal position (BPP) switch electrical connector. 14. Remove the (A) radio ground and the (B) GEM/CTM ground bolts. 15. Disconnect the LH instrument panel main harness connectors. 16. Remove the bulkhead wiring harness electrical connectors from inside the engine compartment. 1. Loosen the bolts. 2. Disconnect the bulkhead electrical connectors. 17. Remove the bulkhead electrical connector from the dash panel. 1. Release the six locking tabs. 2. Remove the bulkhead connector from the dash panel. 18. Disconnect the air bag diagnostic monitor electrical connectors. 19. Disconnect the inertia fuel shutoff switch electrical connector. 20. Remove the RH ground bolts. 21. Disconnect the RH instrument panel main harness connectors. 22. Disconnect the electronic blend door actuator electrical connector. 23. Disconnect the climate control head vacuum harness connector. 24. Remove the instrument panel steering column opening cover reinforcement (04502). 1. Remove the nuts. 2. Remove the instrument panel steering column opening cover reinforcement. 25. Disconnect the air bag sliding contact electrical connectors and the anti-theft sensor electrical connector.

1981-1996 ISUZU Amigo/Pick-ups/Rodeo/Trooper Glow Plugs SYSTEM TESTING REMOVAL AND INSTALLATION MANUAL

download
SYSTEM TESTING See Figures 1, 2, 3 and 4 Fig. Fig. 1: Glow plug system schematic Fig. Fig. 2: Dropping resistor and glow plug relay locations Fig. Fig. 3: Thermo switch location Fig. Fig. 4: Dropping resistor check To test the dropping resistor, check for continuity across the terminals as described in the illustration. If no continuity exists, replace the unit. 1. To test the thermo switch, first remove the switch. Submerge the end of the switch in water and raise the temperature gradually. The switch should be off at 126-140°F (53-60°C) or lower. The switch should be on at 134-145°F (57-63°C) or higher. If not, replace the switch. 2. REMOVAL & INSTALLATION See Figure 5 Fig. Fig. 5: Location of the glow plugs The glow plugs are located under the injection nozzles, and are threaded into the cylinder head. Disconnect the negative (-) battery cable. 1. Disconnect the glow plug and unscrew it from the engine. 2. To install: Lubricate with anti-seize compound before installing the plug. 3. Install and tighten the plug to 65 ft. lbs. (88 Nm). 4. Reconnect the plug wiring. 5. Connect the battery cable and check operation. 6.

2001 Toyota Highlander Sport Utility, Radio, FRONT DOOR SPEAKER INSTALLATION MANUAL

download
2001 Toyota Highlander Sport Utility PRELIMINARY: Disconnect the negative battery cable. ANTENNA: The factory antenna is located atop the right front fender panel. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a Double ISO/DIN style radio. An installation kit is required when installing an aftermarket stereo. 1. Using panel removal tool carefully pry off radio bezel. 2. Extract (6) 10 mm bolts securing radio and climate controls in dash, disconnect and remove. 3. Extract (8) Iso screws securing radio to bracket. 4. Extract (2) Philips screws securing bracket to bezel, pull away and remove radio. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ½” tweeter and a 6 ½” 3-Hole speaker mounted to a factory speaker adapter. 1. Remove screw cover from door opener cup and exract (1) Philips head screw, pry bezel out then forward to remove. 2. Remove inside mirror cover. 3. Pry out door cup and extract (1) Philips screw from beneath. 4. Exract (1) plastic fastener from front top portion of door. 5. Pry off door panel, pull away, disconnect, and remove. 6. Extract (3) 10 mm bolts securing speaker, pull away, disconnect, and remove. REAR DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 5 ¼” 3-Hole speaker mounted in a factory speaker adapter. 1. Remove screw cover from door opener cup and extract (1) Philips head screw, pry bezel out then forward to remove. 2. Pry out door cup and extract (1) Philips screw from beneath. 3. Pry off door panel, pull away, disconnect and remove. 4. Extract (3) 10 mm bolts securing speaker , pull away, disconnect, and remove