Skip to content

isuzu npr wheel alignment specs

You search PDF repair manual about isuzu npr wheel alignment specs, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).

2007-2009 Chevy GM Truck 6-LUG Models Installation Instructions

download
1. Place the vehicle on a flat surface and using a floor jack and jack stands lift the front of the vehicle by the frame so the wheels are off the ground. 2. Remove the front wheel on the driver-side of the vehicle. 3. Remove the sway bar end link. 4. Loosen the three upper strut mounting nuts, but DO NOT REMOVE them. 5. Locate the ABS line and unhook it from the upper control arm. 6. Remove the two lower strut mounting bolts. 7. Loosen the nuts on the upper ball joint, but DO NOT REMOVE them. Note: A hammer may be needed to break the ball joint free. 8. Now remove the ball joint nut, the three upper mounting nuts and remove the strut from the vehicle. 9. With the strut removed from the vehicle, place the leveling spacer on top of the strut assembly, then reinstall the strut assembly in the stock location with the new nuts provided in the kit. 10. Reinstall the upper ball joint nut and sway bar end link. Note: It may be necessary to use a pry bar to aid installation of the strut assembly. It may also be necessary to use a floor jack to raise the lower A-arm to get the ball joint nut installed. 11. Verify that all fasteners have been torqued to factory specs. 12. Reinstall the wheel, and torque to OEM specs. 13. Repeat the above steps on the passenger-side of the vehicle. 14. Adjust your headlights and get the vehicle aligned by a Certified Alignment Technician that is experienced with lifted vehicles. PROFESSIONAL INSTALLATION BY A CERTIFIED MECHANIC IS RECOMMENDED

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

2001 Subaru Legacy GT Sedan AWD F4-2.5L SOHC Steering and Suspension, Wheel Bearing, Service and Repair Manual

download
1. Remove knuckle. Refer to Steering and Suspension. 2. Using ST1 and ST2, remove hub from rear housing. 3. Remove back plate from rear housing. 4. Using a standard screwdriver, remove outer and inner oil seals. CAUTION: Use new oil seals. 5. Using flat bladed screwdriver, remove snap ring. 6. Using ST1 and ST2, remove bearing by pressing inner race. ST1 927430000 HOUSING STAND ST2 927440000 BEARING REMOVER CAUTION: * Do not remove bearing unless damaged. * Do not re-use bearing after removal. 7. Remove tone wheel bolts and remove tone wheel from hub (only vehicle equipped with ABS). 8. Using ST, press hub bolt out. ST 927080000 HUB STAND. CAUTION: Be careful not to hammer hub bolts. This may deform hub. INSPECTION Check the removed parts for wear and damage. If defective, replace with a new one. CAUTION: * If a bearing is faulty, replace it as the bearing set. * Be sure to replace oil seal at every overhaul. ASSEMBLE 1. Using ST, press new hub bolt into place. CAUTION: * Ensure hub bolt closely contacts hub. * Use a 12 mm (0.47 inch) hole in the ST to prevent hub bolt from tilting during installation.

FRONT WHEEL SPEED SENSOR CORROSION REPAIR MANUAL

download
1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN 2002 CHEVROLET AVALANCHE 1999-2002 GMC SIERRA 2000-2002 GMC YUKON, YUKON XL LOCATED IN THE SEVERE CORROSION AREAS LISTED BELOW Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels. 3. Compress the front brake caliper pistons. 3.1. Install a large C-clamp over the top of the caliper housing and against the back of the outboard pad. 3.2. Slowly tighten the C-clamp until the pistons are pushed completely into the caliper bores. 3.3. Remove the C-clamp from the caliper. Important: It is not necessary to remove the front brake caliper from the bracket when removing the bracket in the next step. 4. Remove the two bolts that attach the front brake caliper mounting brackets to the knuckle. Notice: Support the brake caliper with heavy mechanic’s wire, or equivalent, whenever it is separated from its mount, and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. 5. Remove the brake caliper and bracket as an assembly and support it with heavy mechanic’s wire or equivalent. DO NOT disconnect the hydraulic brake flexible hose from the caliper. 6. Mark the relationship of the rotor to the bearing hub. 7. If equipped, remove the rotor retaining push nuts from the wheel studs