Skip to content

isuzu rodeo bumper removal

You search PDF repair manual about isuzu rodeo bumper removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

1981-1996 ISUZU Amigo/Pick-ups/Rodeo/Trooper Glow Plugs SYSTEM TESTING REMOVAL AND INSTALLATION MANUAL

download
SYSTEM TESTING See Figures 1, 2, 3 and 4 Fig. Fig. 1: Glow plug system schematic Fig. Fig. 2: Dropping resistor and glow plug relay locations Fig. Fig. 3: Thermo switch location Fig. Fig. 4: Dropping resistor check To test the dropping resistor, check for continuity across the terminals as described in the illustration. If no continuity exists, replace the unit. 1. To test the thermo switch, first remove the switch. Submerge the end of the switch in water and raise the temperature gradually. The switch should be off at 126-140°F (53-60°C) or lower. The switch should be on at 134-145°F (57-63°C) or higher. If not, replace the switch. 2. REMOVAL & INSTALLATION See Figure 5 Fig. Fig. 5: Location of the glow plugs The glow plugs are located under the injection nozzles, and are threaded into the cylinder head. Disconnect the negative (-) battery cable. 1. Disconnect the glow plug and unscrew it from the engine. 2. To install: Lubricate with anti-seize compound before installing the plug. 3. Install and tighten the plug to 65 ft. lbs. (88 Nm). 4. Reconnect the plug wiring. 5. Connect the battery cable and check operation. 6.

2007 Toyota Camry Rear Bumper Removal and Replacement Manual

download
REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. INSTALLATION 1. INSTALL REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Engage each claw.

2007 TOYOTA FJ CRUISER HEAVY DUTY WINCH BUMPER INSTALLATION INSTRUCTIONS

download
INSTALLATION 1. Remove the screws from the rear corners of the bumper, two in each side. Figure 2 Figure 2 Bumper mounting screws, left side 2. Remove the eight screws along the bottom of the bumper. Figure 3 Figure 3 Lower bumper mounting screws Remove 2 screws in rear of bumper Remove 8 screws in bottom of bumper (4 per side) WARN INDUSTRIES PAGE 4 73465 A0 3. Lift the hood and remove the two screws from the top of the grille. Retain the hardware for use later. Figure 4 Figure 4 Grille fasteners 4. Remove the two plastic fasteners from the top of the grille. Retain the hardware for use later. Carefully pry the center pins up before removing the fasteners. Figure 5 Figure 5 Left grille fastener removal 5. Pull the grille free of the retaining clips with a “sharp” pull. Remove 2 screws Remove 2 plastic fasteners (1each side) Lift center pin then pry fastener out WARN INDUSTRIES PAGE 5 73465 A0 6. Remove five plastic fasteners from the top of the bumper. Two are behind the upper bumper support. Figure 6 Figure 6 Bumper fasteners 7. Pull the bumper corners free by pulling the ends rearward and out. The top of the bumper is snapped into plastic clips just below the fender corners, in front of the flares. Pull the bumper free. Figure 7 Figure 7 Left bumper end removal Remove 5 plastic fasteners (2 behind bumper not shown) WARN INDUSTRIES PAGE 6 73465 A0 8. Remove the two screws that hold each plastic mounting block in place and remove the blocks. Figure 8 Figure 8 LH bumper mounting block 9. Remove the three screws and remove the upper bumper support. Figure 9 Figure 9 Upper bumper support Remove 2 screws and remove plastic block Remove 3 screws Do not remove the nuts on top Bumper mounting block Upper bumper support WARN INDUSTRIES PAGE 7 73465 A0 10. Remove the 8 hex flange nuts and remove the bumper beam. Retain the hardware for bumper installation. Figure 10 Figure 10 Bumper beam, left side shown 11. Remove the four screws and remove the skid pan. Retain the hardware for reinstallation of the skid pan. Figure 11 Figure 11 Skid pan 12. Remove the molded plastic inner fender extensions by clipping or drilling out the rivets holding them to the bottom of the inner fenders. Figure 12 Remove 4 fasteners to remove skid pan Remove 4 flange nuts per side Bumper beam WARN INDUSTRIES PAGE 8 73465 A0 Figure 12 Left side fender extension 12. Locate the 1″ hole in the side of the frame behind the body mount. Drill a 1/2″ hole through the center into the inner wall. The Spacer Tube may be used as a centering tool. Repeat for opposite side. Figure 13 Figure 13 Outside left frame rail 13. Hold the Lower Frame Bracket in position and insert a 12mm bolt with 1/2″ lock washer and flat washer through the bottom hole in the Bracket and into the threaded hole in the frame. Do not tighten yet. Figure 14 Drill ½” hole through center of existing hole into inner frame wall Clip or drill rivets to remove fender extension Fender extension WARN INDUSTRIES PAGE 9 73465 A0 14. Slide a 1/2″ flat washer and Spacer Tube over a 1/2 x 4″ bolt and insert through the Lower Frame Bracket and Frame. Install 1/2″ lock washer and hex nut. Do not tighten yet. Figure 14 15. Slide an Upper Frame Bracket above the frame rail along the inside of the Lower Frame Bracket. Align the holes and insert two 7/16 x 1 1/2″ bolts through the holes and install a lock washer and hex nut on each. Do not tighten yet.