jaguar xj8 sunroof repair manual

You search PDF repair manual about jaguar xj8 sunroof repair manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  jaguar xj8 sunroof repair manual Direct Download speed 5432 Kb/s

  jaguar xj8 sunroof repair manual Full Version speed 8172 Kb/s



2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 2006 ford focus ses repair manual, cft30 scan codes, 1999 chevy S10 - manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, 1999 cavalier A/C instructions, 1998 ford escort auto repair manual free, mpv 2002 p0140, 1999 tahoe repair manual

1984-2001 Jeep Cherokee Ribbed Roof Installation Manual

0

Filed Under (Toyota Manuals) by admin on 11-03-2012

download
In order to accommodate the added thickness of the ribs, longer clamp frame screws or peeling one score off a clamp frame may be required. Install as normal, with any of the following options: A. Use CS-105 (3/8″ x 7/16″ D-shaped foam seal) as main frame sealant 1. Measure and cut sunroof hole as usual 2. Apply self-adhesive CS-105 to sunroof frame (approx. 9 ft. per sunroof). 3. Join CS-105 ends at a 45° angle (not a butt joint). Apply sealant to the joint. 4. Clamp sunroof into hole as usual. No cleanup is required. B. Use non-corrosive silicone sealant to fill between the ribs. 1. Measure and cut sunroof hole as usual 2. Apply a bead of silicone in between the ribs to fill the gap 3. Apply a bead of silicone to sunroof frame (in place of butyl or foam tape) 4. Clamp sunroof into hole as usual. Longer screws may be required on some sunroofs. 5. Cleanup is required. Neatly smooth and feather the silicone around the sunroof frame. NOTE : shims can be helpful, but are not required – metal frames will not twist out of shape II. Composite Frame Sunroofs [see illustrations] Composite frames are not as rigid as metal, and tend to twist inward when installed in ribbed or thick roof skins. Use silicone sealant to seal the frame against the roof, and shims prevent the frame from bending out of shape. A. Required materials: 1.3/16″ thick x 1/4″ – 3/8″ wide [width of outer frame lip] hard black rubber or vinyl material. Body side molding works well. 2.1/8″ thick x 1/4″ wide plastic or vinyl 3. Paint sticks (for use as shim blocks) 4. Non-corrosive silicone sealant 5. Longer clamp ring screws are recommended to accommodate the extra roof thickness B. Procedure: 1. Measure and cut sunroof hole as usual 2. Cut strips of 3/16″ thick material to fit between each rib at the sunroof hole. Run a bead of non-corrosive silicone in troughs between ribs and set strips into it. Fill any gaps with silicone. Objective is to create a flat area for sunroof to seal against. Clean overrun. Allow silicone to set to minimize shifting while installing. 3. Cut strips of 1/8″ thick x 1/4″ wide material to fit between clamp ring and main frame. Glue to inside edge of clamp frame, between screw holes. Without this inside shim, the sunroof main frame will twist, causing gaps betweeen the glass and seal which will result in water leaks. 4. Insert paint sticks in channel gap between edge of sunroof glass and frame. This will minimize inward distortion of the frame. 5. Install sunroof as usual, using non-corrosive silicone sealant (not butyl or foam). Allow silicone to set for at least 1 hour before removing shims

Related Content:

frame type for chevy cruz, how to manall close sunroof on sunfire, how to repair gmc sun roofs, K1500 Frame Repair, webasto hollandia 700 sunroof reset

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, Replacing the reverse band Dodge 1500, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, repair manual for 1998 chevrolet 1500, downloadable schematic for 99 Chevy suburban evap system, ax12-1500 nut torque, 2010 silverado 1500 4 3 liter canister vavle solenoid, how to replace actuator on 2005 chevy 1500, lifter repair on 02 avalanche

Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH Repair Manual

0

Filed Under (Acura Manuals) by admin on 24-11-2011

download
1. To confirm the client’s complaint, test-drive the vehicle on a smooth road, preferably with a slight incline. Set the cruise control between 35 and 40 mph, and monitor the engine rpm using the vehicle’s tachometer, or use the HDS to take a snapshot of the engine rpm. 2. If the engine speed fluctuates several hundred rpm while maintaining a constant vehicle speed, disconnect the EGR valve and retest the vehicle. •If the fluctuation is gone, refer to the EGR troubleshooting in the service manual. •If the engine rpm still fluctuates, and the transmission does not have any other symptoms (shifting problems, slipping, transmission DTCs) go to step 3. 3. Drain the transmission fluid, then strain it through a paint strainer. •If you find little or no contamination in the strainer, the ATF is OK, even if it smells burnt, is discolored, and/or the magnetic drain plug has small chips, flakes, or metal fuzz on it. Go to REPAIR PROCEDURE A . •If you find large amounts of contamination (pieces of metal or friction material) in the strainer, go to REPAIR PROCEDURE B . REPAIR PROCEDURE A 1. Remove the torque converter: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Install the torque converter: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 3. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 4. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. •Start the engine, and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes. REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program , to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner . 3. Install a remanufactured transmission: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 5. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. •Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes

Related Content:

1998 mazda MPV owners manual, 2002 ford thunderbird service manual, freelander engine control module mobility module master, how much for torque converter for 2001 mdx, torque converter problems symptoms for 1999 3 2tl acura, what is a torque shudder

SKYROOF LSS Electric Spoiler Sunroof with Sliding Panel Shade Installation Manual

0

Filed Under (More Manuals) by admin on 11-03-2012

download
SUNROOF KIT PREPARATION 1. Verify that sunroof kit is complete and undamaged. 2. Bench test the sunroof to ensure proper operation. Close the glass fully before continuing. 3. Cover the vehicle interior to keep clean and prevent damage. SUNROOF INSTALLATION 4. Position the sunroof : Place the interior shade tray against the interior headliner and position to avoid any obstructions, allowing 4 inches clearance in front for the motor. Consider obstructions hidden by the headliner such as roof header, side rails and cross bows. NOTE: motor can be located above most consoles. Place the point of a scratch awl against the center inside front lip of the headliner ring (inside edge of the shade tray). Pierce the headliner, and make a slight dent in the roof panel that will be easily visible on top of the vehicle 5. Carefully remove the entire headliner board from the vehicle. 6. If applicable, remove anti-flutter roof bows from the inside of the roof. Do not remove, cut or modify any structural braces, headers or side rails. 7. Measure and mark a front-to-rear center line on the outside of the roof with a marking pencil. Draw a “reference mark” crossing the center line at the roof dent made in step 4. Measure and mark the front cut line 1¼ inches in front of this reference mark. 8. Align the template centerline to centerline on roof. Align front arrow on the template to front cut line mark. Tape template in place, and apply 2 inch wide masking tape around the outside of the cut line to protect the paint while cutting the roof panel. 9. Make a hole large enough to allow entry of the cutting tool, 1 to 3 inches inside the cut line. If necessary, enlarge the hole using hand held metal snips. Cut the sunroof opening with a suitable metal cutting tool. 10. Use a file to clean up any rough edges or burrs around the sunroof opening. 11. Test fit the sunroof. Trim the hole if required and retest. There should be approximately 1/8 inch (4 mm) clearance front to rear, and side to side. Once proper fit has been achieved, remove the masking tape [ peel inward, toward the opening ] and marking pencil lines from the roof. 12. Apply bare metal primer to the cut edge to prevent the metal from rusting. 13. Clean underside of main frame with wax/grease remover. Apply sealant to the inside lip of the main frame. Use nonacidic silicone, butyl, or the supplied foam tape. If using foam or butyl tape, fully overlap the ends in the rear center at a screw hole. Kit includes foam sealant tape, however some technicians prefer silicone or butyl

Related Content:

Webasto Sunroof Problems, inalfa roof systems water leak repair, Webasto Sunroof Reset, inalfa sunroof reset, Webasto Troubleshooting and Repair sunroof, sunroof motor trouble shooting, inalfa sunroof repair, Inalfa Sunroof Problems, 2001 yukon sunroof problems, inalfa roof systems problems

ALL INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 23-04-2012

download
SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. Groan noise during stopping: • Usually caused by glazing of the rotor’s surface as a result of heavy or frequent braking. • Refer to technical bulletins specific to the model of vehicle regarding this issue. • Replace the brake pads, then resurface the rotors and finish them with sand paper. Refer to Brake Service on page 5 for additional detail. Single clunk noise from front suspension when applying the brakes: • The noise is a result of the brake pads shifting in the direction of rotor rotation when the brakes are applied. Can be duplicated by lightly touching the brake pedal. • • If the brake pedal is pushed hard, the noise is less likely to occur. Make sure the brake pads and pad hardware (shims, springs, clips, etc) are installed correctly. Refer to ASIST for vehicle specific brake service information. Refer to Brake Service on page 5 for additional detail. Mull e he engine is started: • st er models, the self check occurs the first aches 5 mph after the engine is started. ors or drums. • WARNING: Brake dust may be hazardous if inhaled. Refer to the Service Manual (ESM) for brake • n and lubrication of brake pads, CAUTION: Do not get grease on the brake pad friction surface. A • Brake Judder is caused by rotor thickness variation and/or rotor run out.

Related Content:

manual for 1993 bmw 325i, Free 98 Honda Accord service Repair Manual, titan 5500 generator manual, lexus engine 2gr-fe chirping squeak noise sb0010-09, Chrysler Pacifica Service Manual PDF, 3 0 gm manual, 2011 durango service manual, 2011 camaro owners manual pdf, 2010 jeep wrangler service manual, 2010 Jeep Wrangler Maintenance Manual

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

0

Filed Under (Ford Manuals) by admin on 15-05-2012

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

Related Content:

0761 emission code ford, 2004 ford ranger owners manual pdf, 86 ford ranger repair manual, ford five hundred repair manual 2007 pdf, ford ranger transmission repair manual, free download jo8c parts book, manual lever position sensor troubleshooting, repair manuel 91 suburu loyle, wiring for a zemmadic 410 pivot

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-07-2012

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

Related Content:

Sienna Sliding Door Cable Replacement, 1998 sienna repair manual, how to fix g-6 door latch, how to remove a chevy tahoe bump stop, lexus door adjustment wind, toyota sienna sliding door repair manual

1999 Jaguar XJ8 Vanden Plas SUSPENSION ADJUSTMENTS And Installation Manual

0

Filed Under (Jaguar Manuals) by admin on 09-05-2012

download
ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES HUB BEARING PRELOAD Hub bearing preload is controlled by shim adjustment between hub assembly and hub outer bearing. Shims are available in various thicknesses. Checking 1. Raise and support vehicle. Remove wheel assembly. Clamp dial indicator mount to hub carrier. Ensure dial indicator pointer contacts hub flange. 2. Using 2 levers between hub and hub carrier, press hub outward. Note reading on dial indicator. The difference between dial indicator readings is preload of hub bearing. For adjustment, see HUB CARRIER under REMOVAL & INSTALLATION. REAR SUSPENSION HEIGHT 1. Ensure vehicle has full fuel tank, all fluids are topped off and tire pressures correct. Roll vehicle about 30 feet on a level surface. Measure distance between differential support plate at both sides and ground. See Fig. 2 . 2. Height measurement for coupe and convertible. If height is not within specification, check all bushings and replace as necessary. If bushings are okay, replace rear springs. NOTE: See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. 1999 Jaguar XJ8 Vanden Plas 1999-2000 SUSPENSION’ ‘Rear Fig. 2: Measuring Rear Suspension Height Courtesy of JAGUAR CARS, INC. REMOVAL & INSTALLATION “A” FRAME Removal 1. Raise vehicle and support with stands. Remove “A” frame to final drive unit rear bracket securing bolts and front bracket inner securing nuts and bolts. See Fig. 3 . 2. Position a suitable wood and jack under final drive unit drive flange, operate jack to support final drive unit. Unscrew and remove both “A” frame outer bush to body and bracket securing bolts. See Fig. 4 . Unscrew and remove “A” frame left and right outer bush bracket to body securing bolts. 3. Lower jack approximately one inchto improve access. Unscrew and remove “A” frame to final drive unit front bracket intermediate securing bolts. Unscrew and remove “A” frame to final drive unit fron

Related Content:

how remove harmonic balancer on 2000 jaguar xkr 4 0l, 1996 jaguar vanden plas crankshaft speed sensor diagnosis, jaguar xj8 rear wheel bearing replacement, jaguar repair manual 1999 xk8 pdf download free, blower resistor replacement 04 vanden plas, 99 jaguar xj8 throttle body, 1999 Sebring Convertible JXI owners manual, 1999 jaguar xj8 manual, 1999 jag vanden plas owners manual, xf wheel alignment

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 2006 ford focus ses repair manual, cft30 scan codes, 1999 chevy S10 - manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, 1999 cavalier A/C instructions, 1998 ford escort auto repair manual free, mpv 2002 p0140, 1999 tahoe repair manual