kia sedona p0507 and p0430

You search PDF repair manual about kia sedona p0507 and p0430, if there are search results will appear below. If search results do not exist, please search by others keyword.



  kia sedona p0507 and p0430 Direct Download speed 5432 Kb/s

  kia sedona p0507 and p0430 Full Version speed 8172 Kb/s



Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

0

Filed Under (Kia Motors Manuals) by admin on 11-01-2012

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

Related Content:

how to adjust a cat forklift throttle position sensor, how to check 2006 G6 throttle sensor, kia sorento throttle position sensor, 2008 silverado replace tps, 2006 kia amanti idle speed adjustment, tps sensor 5 3l vortec, throttle body relearn for ford f150, Throttle body relearn for a ford f150, replaced throttle body new on my 2004 saturn vue and ligjt still comes on and off, replace throttle body sensor ford escape

2003 Kia Rio L4-1.6L DOHC TIMING BELT Service and Repair Manual

0

Filed Under (Kia Motors Manuals) by admin on 28-06-2012

download
REMOVAL 1. Disconnect negative battery cable. 2. Loosen power steering lock bolts and nuts accordingly and remove tension from Power Steering (P/S) and/or Air Conditioning (A/C) compressor drive belt . 3. Remove P/S and/or A/C drive belt . 4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts. 6. Remove water pump pulley. 7. Remove crankshaft pulley and timing belt guide plate. 8. Remove upper and lower timing belt covers. 9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine. 10. Check that “I” mark on intake camshaft pulley is aligned with mark on cylinder head cover and “E” mark on exhaust camshaft pulley is aligned with mark on cylinder head cover. NOTE: Do not move camshaft or crankshaft once timing marks have been correctly positioned. 11. Loosen tensioner pulley lock bolt. 12. Protect timing belt with a rag. 13. Remove tensioner pulley. 14. Remove timing belt. NOTE: Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation. INSPECTION NOTE: Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt. 1. Replace timing belt if it is contaminated with oil or grease

Related Content:

o2 Chevy Blazer check engine light code po763, crankshaft timming mark isuzu kb300, kia picanto radiator how to remove, sensor efi system kia carens

2004 Kia Sorento EX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Kia Motors Manuals) by admin on 03-06-2012

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

Related Content:

change timing belt 2004 kia sorento, 2003 kia sorento power steering pump replacement, 2004 sorento replace drive belts, how to install a motor mount on a kia sedona, how to replace the camshaft pulley bolt on a 2004 Kia Sorento here at home?, how to take a intake manifold off of a 2003 kia sorento, how to time a 2004 kia sorento, kia sedona steering pump rebuilt, kia sorento drive shaft repair

2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

0

Filed Under (Kia Motors Manuals) by admin on 16-07-2012

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak

Related Content:

pto connection on 2002 f450, ford 555b engine oil capacity, kia transmission fuild temperture sensor, instructions on radio for 2004 kia sorento, kancil manifold supply air inlet, kia p0750 p0755 p0765, kia sedona 2004 repair manual pdf torrent, mercury cougar beeping noise in idle, park pin in a 4l60e transmission, 1986 190e 2 3 throttle linkage adjustment

Kia 2002 Saturn SL will set if TP sensor voltage is less than 0.2 volts

0

Filed Under (Kia Motors Manuals) by admin on 26-05-2011

download
The throttle position (TP) sensor is a potentiometer that varies resistance according to changes in throttle plate position. The powertrain control module (PCM) measures the signal voltage from the TP sensor which is a reduced value of the PCM 5-volt reference. The voltage ranges from 0.4 (+/-0.2) volts at 0% throttle position to 4.7 volts at wide open throttle. DTC P0122 sets when the TP sensor signal voltage at the PCM is below the calibrated voltage value. DTC Parameters DTC P0122 will set if TP sensor voltage is less than 0.2 volts when: z The condition exists for longer than 10 seconds. z The ignition is ON. DTC P0122 diagnostic runs continuously with ignition ON. DTC P0122 is a type A DTC. Diagnostic Aids Important If DTC P1635 is set, diagnose that DTC first. 2002 Saturn SL
To locate an intermittent problem, use a scan tool to monitor TP SENSOR voltage with ignition ON, engine OFF. Wiggling the wires while watching for a change in TP SENSOR voltage may locate the area where an open or short to ground in the wiring could lie. An intermittent open in the TP SENSOR can cause this DTC to set. Use the scan tool to monitor TP SENSOR as the accelerator pedal is slowly depressed. The voltage should change smoothly from 0.4 volts at 0% throttle, to 4.7 volts at wide open throttle (+/-0.2 volts).

Carbon Fiber Seat Heater Installation Instructions

0

Filed Under (More Manuals) by admin on 18-04-2012

download
Installation Summary – Overview 1. Remove the existing front or rear seat covers. 2. Take note of whether the covers reattach by way of Velcro or Hog rings. 3. The Wire Connector with Purple & Black colored wires is seat the connector which will enable the use of both High & Low temperature functions. 4. Place the heating pads on the seat and at the Listing Reattachment Area mark the pad with a pen. You will be cutting 2 holes per pad. The holes should be equidistant. Example: If your listing length for Velcro or hog rings is 12′ in length then, make a hole at the 4″ & 8″ point. (The Seat Heaters may also be trimmed in length) 5. Now separate the protective adhesive backing at the backside of the heating pads and carefully align your pad and holes with the listing area and press the pads against the seat foam to secure the pad in place. 6. Reinstalling the Covers: Tip: For Backrest Covers, turn the cover inside-out and roll the cover back down the backrest, then reattach the plastic clips. For Seat Bottoms, start by attaching your Velcro or hog ring listings and then proceed to work outwards. Don’t work from front to back or from left to right – start from the middle then work outwards! 7. Switch Location: The diameter of the hole for the switch is 13/16″ or 21mm & the most common location for the switch is on the plastic trim located at the side of the seat. 8. Power Sources: The most common sources are the Accessory Panel, Power Seat, Cigarette Lighter/Accessory Outlet, and Steering Column. However, we recommend drawing power via a relayed key- start trigger sourced directly from the battery. This avoids onboard electronic system interference. ***Warning: If you are installing seat heaters into a vehicle which has a Passenger Side Occupancy Detection System for the Air Bags , You Must Observe The Following: When you remove the seat bottom seat covers, identify whether or not the seat is equipped with topside sensors. They are usually visible and resemble flat circular disks which are interconnected or rectangular in shape. If you are uncertain, you must contact a service department professional for confirmation. Toyota, Kia and Hyundai usually locate the sensors on top of the seat bottom core foam. Honda usually locates the sensors on the face of the seat backrest. In either case, for that particular seat (usually passenger sides only) use only the 2-temp wire connector with one of our seat heater pads. (Disconnect one of the other pads – you will not need it) *The dual temperature wire connector is attached to a black and a purple wire. This will allow dual temperature function with the use of only a single pad

Related Content:

renault df072 passenger second row seat belt pretensioner

2000 Saturn SL2 L4-1.9L DOHC VIN 7 Body/ Electrical Service Manual

0

Filed Under (Kia Motors Manuals) by admin on 31-05-2011

download
1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key. ^If the ignition key turns, proceed to step 30. ^If the ignition key does not turn replace the ignition module/passlock sensor by continuing with next step. 6. Disable SIR system. Refer to “Disabling Frontal Inflators” procedure in the 2000/2001 S-Series Body Electrical Volume II Service Manual

Related Content:

1996 satrun ignition housing

Related Content:

how to adjust a cat forklift throttle position sensor, how to check 2006 G6 throttle sensor, kia sorento throttle position sensor, 2008 silverado replace tps, 2006 kia amanti idle speed adjustment, tps sensor 5 3l vortec, throttle body relearn for ford f150, Throttle body relearn for a ford f150, replaced throttle body new on my 2004 saturn vue and ligjt still comes on and off, replace throttle body sensor ford escape