Skip to content

kia sorento 2 4 engine timing belt diagram

You search PDF repair manual about kia sorento 2 4 engine timing belt diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Kia Sorento EX TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

2001 Honda Prelude Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Manual

download
Removal and Installation REMOVAL NOTE: * Turn the crankshaft pulley so the No. 1 piston is at Top Dead Center (TDC) before removing the belt. * Inspect the water pump after removing the timing belt. * Replace the timing belt and timing balancer belt at 105,000 miles (168,000 km) according to the maintenance schedule (normal conditions/severe conditions). If the vehicle is regularly driven in one or more of the following conditions, replace the timing belt and timing balancer belt at 60,000 miles (U.S.A.) 100,000 km (Canada). * In very high temperatures (over 110°F, 43°C). * In very low temperatures (under -20°F, -29°C). 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio’s preset buttons. 2. Disconnect the battery negative terminal first, then the positive terminal. 3. Remove the wheel well splash shield. 4. Loosen the adjusting bolt, locknut and mounting bolt, then remove the Power Steering (P/S) pump belt. 5. Remove the alternator terminal and connector. 6. Loosen the adjusting bolt, mounting bolt and lock nut, then remove the alternator belt. 7. Remove the side engine mount. NOTE: * Support the engine with a jack before removing the side engine mount and upper bracket assembly is removed. * Make sure to place a cushion between the oil pan and the jack 8. Remove the dipstick and the tube. 9. Remove the cylinder head cover. NOTE: The procedures in steps 10 and 11 are for reusing the timing belt. For replacing the timing belt, skip these procedures and go to step 12. 10. Use an open-end wrench to loosen the maintenance bolt. If it cannot be loosened with an open-end wrench, a box wrench can be used after removing the lock pin. NOTE: Use of a tool should be limited to initial loosening only 11. Unscrew the maintenance bolt by hand until it stops. The auto-tensioner bracket is now fixed. NOTE: * Never use a tool to unscrew the maintenance bolt after initial loosening it. * If the auto-tensioner has been extended and the timing belt cannot be installed, remove the auto-tensioner, compress it and reinstall it. 12. Remove the middle cover. NOTE: Do not use the middle cover to store removed items. 13. Remove the pulley bolt and crankshaft pulley

1996 TOYOTA T100 ENGINE MECHANICAL TIMING BELT INSTALLATION

download
1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on the timing pulley, facing the flange side inward. 2. INSTALL NO. 1 IDLER PULLEY AND NO.2 IDLER PULLEY (a) Using a 10 mm hexagon wrench, install the No.1 idler pulley with the plate washer and bolt. Torque: 35 N·m (350 kgf·cm, 26 ft·lbf) (b) Check that the pulley bracket moves smoothly. (c) Install the No.2 idler pulley with the bolt. Torque: 40 N·m (400 kgf·cm, 30 ft·lbf) (d) Check that the pulley moves smoothly. 3. TEMPORARILY INSTALL TIMING BELT NOTICE: The engine should be cold. (a) Use the crankshaft pulley bolt to turn the crankshaft and align the timing marks on the crankshaft timing pulley and on the oil pump body. (b) Remove any oil or water on the crankshaft timing pulley, idler pulley and water pump pulley, and keep them clean. NOTICE: Only wipe the pulleys; do not use any cleansing agent. (c) Align the installation mark on the timing belt with the drilled mark of the crankshaft timing pulley. (d) Install the timing belt on the crankshaft timing pulley, No.1 idler and water pump pulleys. 4. INSTALL TIMING BELT GUIDE Install the guide, facing the cup side outward

2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak

1997 Chrysler Sebring JXi TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
1. Disconnect negative battery cable from jumper terminal. Raise and support vehicle. Remove right front wheel. Remove accessory drive belt splash shield from right wheelwell. 2. Remove accessory drive belts. Remove right engine support assembly vertical bolts from bottom side of frame rail (timing belt end of engine). 3. Lower vehicle. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine support assembly to engine block bracket. 4. Move the A/C drier aside with hoses attached. Remove coolant reservoir tank. Remove right engine support assembly. Remove 3 bolts attaching engine support bracket to engine block, and remove bracket. 5. Remove crankshaft vibration damper. Remove power steering pump (hoses attached) and bracket from engine block. Remove timing belt covers. 6. Rotate crankshaft to align camshaft and crankshaft timing marks. 7. If reusing old timing belt, mark timing belt direction of rotation for installation reference. Loosen timing belt automatic tensioner bolts. Remove timing belt. Remove automatic tensioner. Installation 2.5L VIN H (Cirrus, Sebring Convertible & Stratus) 1. Place automatic tensioner into vise, and SLOWLY compress plunger. When plunger is compressed into tensioner body, install locking pin through body and plunger holes to retain plunger until tensioner is installed. See Fig. 13 . 2. Index tensioner in vise the same direction as installed. This will ensure proper pin orientation when tensioner is installed in engine.