Skip to content

kv6 belt

You search PDF repair manual about kv6 belt, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak

1997 Chrysler Sebring JXi TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
1. Disconnect negative battery cable from jumper terminal. Raise and support vehicle. Remove right front wheel. Remove accessory drive belt splash shield from right wheelwell. 2. Remove accessory drive belts. Remove right engine support assembly vertical bolts from bottom side of frame rail (timing belt end of engine). 3. Lower vehicle. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine support assembly to engine block bracket. 4. Move the A/C drier aside with hoses attached. Remove coolant reservoir tank. Remove right engine support assembly. Remove 3 bolts attaching engine support bracket to engine block, and remove bracket. 5. Remove crankshaft vibration damper. Remove power steering pump (hoses attached) and bracket from engine block. Remove timing belt covers. 6. Rotate crankshaft to align camshaft and crankshaft timing marks. 7. If reusing old timing belt, mark timing belt direction of rotation for installation reference. Loosen timing belt automatic tensioner bolts. Remove timing belt. Remove automatic tensioner. Installation 2.5L VIN H (Cirrus, Sebring Convertible & Stratus) 1. Place automatic tensioner into vise, and SLOWLY compress plunger. When plunger is compressed into tensioner body, install locking pin through body and plunger holes to retain plunger until tensioner is installed. See Fig. 13 . 2. Index tensioner in vise the same direction as installed. This will ensure proper pin orientation when tensioner is installed in engine.

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

2003 Lexus ES 300 TIMING BELT Removal And Installation Manual

download
TIMING BELT Removal (ES 300) 1. Raise and support vehicle. Remove right side front wheel. Remove right fender apron seal. Remove accessory drive belts. Lower vehicle. Disconnect engine coolant reservoir hose from water outlet. Disconnect ground strap connectors. 2. Remove engine moving control rod and engine mounting bracket No. 2 (right side), located near timing belt cover. Remove generator-to-engine bracket for access to timing belt covers. 3. Using Pulley Holder (09213-54015) or equivalent and Handle (09330-00021) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove No. 1 and No. 2 timing belt covers and gaskets. See Fig. 1 . Remove transverse engine mounting bracket from front of engine. Note direction of timing belt guide installation for reassembly reference. Remove timing belt guide. 4. Temporarily install crankshaft pulley bolt and washer in crankshaft. Using crankshaft pulley bolt, rotate crankshaft clockwise until timing mark on crankshaft sprocket aligns with timing mark on oil pump body. See Fig. 2 . 5. Ensure timing marks on camshaft sprockets are aligned with timing mark on No. 3 timing belt cover. See Fig. 2 . If timing marks are not aligned, rotate crankshaft clockwise one full revolution (360 degrees). Remove crankshaft pulley bolt. 6. If reusing old belt, ensure there are 3 installation marks and front arrow marked on belt. See Fig. 3 . If not, place mating mark on belt where it contacts the crankshaft and camshaft sprockets. Also, mark belt with arrow showing direction of rotation. 7. Alternately loosen 2 bolts, and remove timing belt tensioner and dust boot. DO NOT hold tensioner with push rod facing downward. Remove timing belt in the following sequence: No. 1 idler pulley, right camshaft sprocket (firewall side), No. 2 idler pulley, left camshaft sprocket (front of vehicle side), left camshaft sprocket (front of vehicle side), water pump pulley, then crankshaft sprocket

1989 Nissan Pickup (200SX & 300ZX) TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal (200SX & 300ZX) 1. Disconnect negative battery cable. Release fuel pressure from system. Raise and support vehicle. Remove right wheel and engine side cover (if necessary). Drain cooling system. Remove cooling fan duct. Remove engine coolant reservoir. Remove actuator and remove radiator hoses. Do not allow coolant to contact drive belts. 2. Remove front upper and lower belt covers. See Fig. 1 . Remove drive belts and set No. 1 cylinder at TDC of compression stroke. Remove idler bracket of compressor drive belt and crankshaft pulley. Remove timing belt by removing timing belt tensioner and return spring Inspection (200SX & 300ZX) Visually inspect condition of timing belt. Inspect for cracks, wear, breaks, and oil/coolant saturation. Installation (200SX & 300ZX) 1. Ensure that piston No. 1 is at TDC of compression stroke. Remove valve covers and loosen all rocker shaft bolts. Do not bend timing belt. Install tensioner and return spring. 2. Turn tensioner clockwise and temporarily tighten lock nut. Install timing belt. Align White lines on timing belt with punch mark on camshaft pulleys and crankshaft pulley. Arrow on timing belt must be pointing toward front belt covers. 3. Using Allen wrench, slowly turn tensioner clockwise and counterclockwise 2 or 3 times. When camshafts and crankshaft marks are aligned, tighten tensioner lock nut. See Fig. 2 . Ensure that camshaft lobes are correctly positioned. Tighten rocker shaft bolts in 2 stages. 4. Refill and bleed air from cooling system. To complete installation, reverse removal procedures. Adjust drive belts to proper tension