Skip to content

location of bank 2 sensor 2 kia sedona

You search PDF repair manual about location of bank 2 sensor 2 kia sedona, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997 Chevrolet Chevy K Pickup DTC P0152 HO2S Circuit High Voltage Bank 2 Sensor 1 Repair Manual

The number below refers to the step number on the diagnostic table. 2. This test determines if the conditions exist in order to set the DTC P0152. 3. If the HO2S (Bank 2, Sensor 1) is intrnally shorted, the HO2S (Bank 2, Sensor 1) voltage displayed on a scan tool will be over 1.0 volt (1000 mV). Important: Before clearing DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. This data will be lost when the Clear DTC Information function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Connect the scan tool. 2. Run the engine at the normal operating temperature. 3. Place the vehicle in park or neutral. 4. Apply the parking brake. 5. Increase the engine speed to the specified value. Does the scan tool data display indicate HO2S sensor voltage fixed above the specified value? 1200 RPM 0.976 V (976 mV) Go to Step 3 Go to Step 4 3 1. Disconnect the HO2S. 2. Turn on the ignition while leaving the engine OFF. 3. Turn ON the ignition leaving the engine off. Does the scan tool data display indicate the HO2S voltage near the specified value? 400 mV) Go to Step 6 Go to Step 5 4 The DTC is intermittent. Are any additional DTCs set? — Go to the applicable DTC table Go to Diagnostic Aids 5 1. Check for a short to voltage in the HO2S Signal circuit. 2. If a problem is found, repair the circuit as necessary. Refer to Wiring Repairs in Electrical Diagnosis. Was the HO2S Signal circuit shorted? — Go to Step 8 Go to Step 7 6 Replace the HO2S. Refer to Heated Oxygen Sensor (HO2S) Replacement . Is the action complete? — Go to Step 8 — 7 Replace the VCM. Important: When replacing the VCM, the new VCM will need to be programed. Refer to VCM Replacement/Programming . Is the action complete? — Go to Step 8 — 1. Use the scan tool in order to select the DTC and the Clear DTC Information functions.

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.

4WD Switch Indicator Lights Flashing, 4WD Inoperative, DTCs C0327, P0500, P0836, P1875 Set (Replace Encoder Motor Sensor, Reprogram TCCM, Inspect Front Drive Axle Engagement Sleeve for Damage/Repair if Necessary)

Correction Important: For ease of reassembly, shift the transfer case assembly to 2HI for the NV263 (NP1), or Neutral for the NV246 (NP8) prior to removing any components. For information on placing the NV246 (NP8) transfer case in NEUTRAL, see the procedure at the end of this bulletin. 1. Remove the transfer case and front axle/engine skid plates (if equipped). 2. Disconnect and position the front propeller shaft aside. 3. Disconnect the transfer case encoder motor wiring harness. 4. Remove the three (3) bolts that retain the encoder motor to the transfer case. 5. Separate the encoder motor assembly from the transfer case and place it on a work bench. Important: DO NOT REMOVE THE SCREWS INDICATED WITH THE (1) IN THE ABOVE ILLUSTRATION. 6. Remove the four screws on the outer perimeter of the encoder motor housing. Important: For proper timing and ease of reassembly, hold the gear in place as your remove the cover from the encoder motor assembly with your thumb or finger. 7. Carefully remove the cover from the encoder motor assembly. The cover has a seal on the bottom side. Place the cover in a position to protect this seal from damage and/or contamination. Important: Observe the location of the punch mark on the large gear in relation to the timing mark on the housing if the transfer case was placed in the 2HI for the NV263 (NP1), or Neutral for the NV246 (NP8). The timing marks should be within one tooth of proper alignment. If not, you must note the timing mark positions for reassembly. 8. Locate the two shims; one on the small gear and another on the larger gear. Set them aside on a clean surface for reuse. Important: After removing the large gear from the housing, a dark gray phenolic spacer should remain in the casting where the bottom of the large gear resides. Locate this spacer and save for reuse. 9. Carefully lift the large gear from the housing. The sensor and wiring harness will come with the gear. 10. Disconnect the wiring from the sensor. 11. Separate the sensor from the large gear.


ACTIONS: • If you only have DTC P0340, replace only Bank 1 CMP (Camshaft Position) Sensor. • If you only have DTC P0345, replace only Bank 2 CMP (Camshaft Position) Sensor. • If you have both codes, replace both sensors. • For a “hard to start warm” incident, replace both sensors, even if you have no codes. Refer to sections EC and EM in the correct Service Manual for sensor replacement information. If replacement of the sensors does not solve your incident, go back to ASIST for further diagnostic and repair information. PARTS INFORMATION DESCRIPTION PART # QUANTITY Camshaft Position Sensor- Bank 1 23731-6J906 1 Camshaft Position Sensor- Bank 2 23731-AL616 1 CLAIMS INFORMATION Submit a Primary Failed Part (PP) line claim using the following claims coding: DESCRIPTION PFP OP-CODESYSDIAFRT RPL One Camshaft Position Sensor (Bank 1 or Bank 2) (1) DE64AA AA 32 (2) RPL Both Camshaft Position Sensors (Banks 1 and 2) (1) DE67AA AA 32 0.3 hrs. (1) Reference the Parts Information table and use the indicated sensor P/N’s as the PFP. (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT

1995 Volvo 850 L5-2.3L Turbo Relay Identification and Location

Relay Identification and Location Relays Inside the Central Electrical Unit 101-102Control module, cruise control (4/3) 103 Fuel pump relay (2/23) 104,108Main headlight relay with bulb malfunction indicator (2/1) 105 Overload relay +X supply (2/30) 106 Overload relay +15 supply (2/31) 107 Overload relay +X supply (2/60) 201 Fog light relay (2/2) 202 Relay, deadlock setting (2/47) 203 Relay, windshield intermittent wiper (2/4) 204 Relay, tailgate intermittent wiper (2/16) 205-206Relay, central lock and delayed inside lighting (2/7) 207 Speed warning (2/51) or exhaust temp. sensor relay (2/15) 208 Relay, heated rear window and door mirrors (2/44) 210-211Relay, anti-theft alarm (2/28) 212 Relay, seat belt reminder/key warning (2/5) 213 Front fog lights, bridge (25/9) 214 Relay, heated rear seat (2/43) If the car is not equipped with a theft alarm, position 210 is bridged and 211 is unconnected. Relays Outside the Central Electrical Unit