manual pulley

You search PDF repair manual about manual pulley, if there are search results will appear below. If search results do not exist, please search by others keyword.



  manual pulley Direct Download speed 5432 Kb/s

  manual pulley Full Version speed 8172 Kb/s



2002 HONDA ACCORD – Timing Belt and Balancer Belt Installation Instructions

0

Filed Under (Honda Manuals) by admin on 22-01-2011

download
1. Remove and clean the balancer belt drive pulley. 2. Clean the timing belt pulleys, and the upper and lower timing cover. 3. Set the crankshaft to TDC. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head. -1 Drive pulley (A). -2 Tensioner pulley (B). -3 Water pump pulley (C). -4 Camshaft pulley (D). 6. Loosen and retighten the adjusting nut to tension the timing belt. 7. Clean any oil off both faces of the balancer belt drive pulley. 8. Check the lower cover rubber seal for cracks and other damage. NOTE: ?If the rubber seal is coming off, apply liquid gasket to the lower cover and reinstall the rubber seal. Wipe off any liquid gasket that is pressed out. ?When replacing the rubber seal, clean the lower cover groove, cut the repair rubber seal to length, and put the rubber seal into the groove evenly. 9. Install the balancer belt drive pulley and the lower cover. 10. Temporarly install the crankshaft pulley and bolt. 11. Rotate the crankshaft pulley five or six turns counterclockwise to seat the timing belt on the pulleys. 14. Check the camshaft pulley marks. ?If the camshaft pulley marks are also at TDC, go to step 15. ?If the camshaft pulley marks are not at TDC, remove the timing belt and repeat steps 3, 4 and 5. 15. Remove the crankshaft pulley and the lower cover. 16. Turn the crankshaft to TDC again. 17. Lock the timing belt adjuster arm in place with one of the 6 mm timing cover bolts. 18. Loosen the adjusting nut 2/3-1 turn, and make sure the balancer belt tensioner moves freely. Then push the tensioner up and retighten the adjusting nut. 19. Align the rear balancer shaft pulley with a 6 x 100 mm bolt (or equivalent). -1 Remove the bolt (A) and washer (B) from the maintenance hole (C). -2 Scribe a line on a 6 x 100 mm bolt, 74 mm (2.9 in) from the end

Related Content:

2002 honda accord 2 3 timing belt tension adjustment, 2003 buick lasabre serpentine belt idler pulley torque spec, 2005 audi 3 2 tdc diagram, 2006 kia sorento camshaft pulley repair manual pdf, how to replace a tensioner pulley on a 2006 mazda 5, lincoln ls crank pulley diagram, mazda 6 crankshaft tool, pulley configuration 2001 buick lesabre, Residue from serpentine bolt on smooth pulleys

1996 TOYOTA T100 ENGINE MECHANICAL TIMING BELT INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 24-09-2011

download
1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on the timing pulley, facing the flange side inward. 2. INSTALL NO. 1 IDLER PULLEY AND NO.2 IDLER PULLEY (a) Using a 10 mm hexagon wrench, install the No.1 idler pulley with the plate washer and bolt. Torque: 35 N·m (350 kgf·cm, 26 ft·lbf) (b) Check that the pulley bracket moves smoothly. (c) Install the No.2 idler pulley with the bolt. Torque: 40 N·m (400 kgf·cm, 30 ft·lbf) (d) Check that the pulley moves smoothly. 3. TEMPORARILY INSTALL TIMING BELT NOTICE: The engine should be cold. (a) Use the crankshaft pulley bolt to turn the crankshaft and align the timing marks on the crankshaft timing pulley and on the oil pump body. (b) Remove any oil or water on the crankshaft timing pulley, idler pulley and water pump pulley, and keep them clean. NOTICE: Only wipe the pulleys; do not use any cleansing agent. (c) Align the installation mark on the timing belt with the drilled mark of the crankshaft timing pulley. (d) Install the timing belt on the crankshaft timing pulley, No.1 idler and water pump pulleys. 4. INSTALL TIMING BELT GUIDE Install the guide, facing the cup side outward

Related Content:

1989 mazda b2200 crankshaft pulley bolt tightening torque, location of idler pullies on 3 8 supercharged buick 1998 riviera, how to replace idler pulley 2003 town and country, how to remove idler pulley from 2002 chrysler town and country, how to change a idler pulley on a 2000 tundra, crankshaft pulley installer tool 2006 pt cruiser 2 4 engine, 2007 maxima idel pulley diagram, 1998 honda civic idler arm you tube replacement instructions, 1994 lincoln town car idler pulley torque, replace crankshaft pulley on 1999 mercury marquis

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, montero crank shaft pully removal, montero xls bleeding cooling system how, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

2003 Lexus ES 300 TIMING BELT Removal And Installation Manual

0

Filed Under (Lexus Manuals) by admin on 04-07-2012

download
TIMING BELT Removal (ES 300) 1. Raise and support vehicle. Remove right side front wheel. Remove right fender apron seal. Remove accessory drive belts. Lower vehicle. Disconnect engine coolant reservoir hose from water outlet. Disconnect ground strap connectors. 2. Remove engine moving control rod and engine mounting bracket No. 2 (right side), located near timing belt cover. Remove generator-to-engine bracket for access to timing belt covers. 3. Using Pulley Holder (09213-54015) or equivalent and Handle (09330-00021) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove No. 1 and No. 2 timing belt covers and gaskets. See Fig. 1 . Remove transverse engine mounting bracket from front of engine. Note direction of timing belt guide installation for reassembly reference. Remove timing belt guide. 4. Temporarily install crankshaft pulley bolt and washer in crankshaft. Using crankshaft pulley bolt, rotate crankshaft clockwise until timing mark on crankshaft sprocket aligns with timing mark on oil pump body. See Fig. 2 . 5. Ensure timing marks on camshaft sprockets are aligned with timing mark on No. 3 timing belt cover. See Fig. 2 . If timing marks are not aligned, rotate crankshaft clockwise one full revolution (360 degrees). Remove crankshaft pulley bolt. 6. If reusing old belt, ensure there are 3 installation marks and front arrow marked on belt. See Fig. 3 . If not, place mating mark on belt where it contacts the crankshaft and camshaft sprockets. Also, mark belt with arrow showing direction of rotation. 7. Alternately loosen 2 bolts, and remove timing belt tensioner and dust boot. DO NOT hold tensioner with push rod facing downward. Remove timing belt in the following sequence: No. 1 idler pulley, right camshaft sprocket (firewall side), No. 2 idler pulley, left camshaft sprocket (front of vehicle side), left camshaft sprocket (front of vehicle side), water pump pulley, then crankshaft sprocket

Related Content:

2003 santa fe 2 7 timing belt marks, where is the air flow meter on a kb300 lx pdf, 2003 2 4 santa fe out two teeth on intake cam for timing rough idle, 2003 lexus 3 0camshaft timing marks, 2003 lexus 3 0camshaft timing marks diagram, how to tighten alternator belt on a toyota 1zr

1994 Toyota Camry DX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 22-01-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution. 7. Loosen No. 1 idler pulley bolt. See Fig. 1 . Move No. 1 idler pulley outward, away from timing belt as far as possible. Temporarily retighten No. 1 idler pulley bolt. Remove timing belt from camshaft sprocket. 8. Using Pulley Holder (SST 09213-54015) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. 9. Using gear puller, remove crankshaft pulley. Remove No. 1 timing belt cover and gasket. Note direction of timing belt guide installation. See Fig. 1 . Remove timing belt guide. 10. Loosen No. 1 idler pulley bolt. See Fig. 1 . Remove timing belt from crankshaft sprocket. Remove idler pulleys (if necessary).

Related Content:

96 Toyota Camry 3 0 Timing Marks, TOYOTA 4Y TIMING MARKS, toyota 7A-FE timing belt alignment marks, Toyota Camry Crankshaft Pulley Removal

1997 Mitsubishi Diamante LS Sedan Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 10-04-2012

download
REMOVAL 1. Remove the crankshaft pulley with pulley holding pins and end yolk holder tool Nos. MD998715 and MB990767, or equivalents. 2. Refer to the illustration for the service procedures, noting the following: 3. Before removing the timing belt, align the timing marks and loosen the center bolt on the tension pulley to remove the timing belt. 4. If the auto tensioner rod is in its fully extended position, reset it as follows: a. Keep the auto tensioner level and, in that position, clamp it in the vise with soft jaws. NOTE: Make a mark on the back of the timing belt, indicating the direction of rotation, so it may be reassembled in the same direction if it is to be reused. Zoom Sized for Print Zoom Sized for Print b. Push in the rod little by little with the vise until the set hole A in the rod is aligned with that B in the cylinder. c. Insert a wire, 1.4 mm (0.055 inch) in diameter, into the set holes. d. Unclamp the auto tensioner from the vise. e. Install the auto tensioner. INSTALLATION 1. Align the timing marks of the camshaft sprockets and crankshaft sprocket. 2. Install the timing belt by the following procedure so that there is no defection in the timing belt between each sprocket and pulley. a. Crankshaft sprocket b. Idler pulley c. Camshaft sprocket (front side) d. Water pump pulley e. Camshaft sprocket (rear side) f. Tension pulley 3. Turn the camshaft sprocket (right side) counterclockwise until the tension side of the timing belt is firmly stretched, and then check again that all timing marks are aligned. 4. Use the tension pulley socket wrench tool No. MD998769, or equivalent, to push the tension pulley into the timing belt, and then temporarily tighten the center bolt. 5. Use the crankshaft sprocket spacer tool No. MD998769, or equivalent, to turn the crankshaft 1/4 of a turn counterclockwise and then turn it again clockwise until the timing marks are aligned.

2004 Mitsubishi Lancer O-Z Rally TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 06-06-2012

download
Fig. 79: Aligning Timing Belt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow. 4. Temporarily tighten the tensioner pulley bolt. 5. Remove the timing belt. Fig. 80: Tightening Tensioner Pulley Bolt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. INSTALLATION SERVICE POINTS >> A << TIMING BELT INSTALLATION CAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction. CAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position. 1. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Then temporarily tighten tensioner bolt. Fig. 81: Adjusting Timing Belt Tensioner Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Align each of the camshaft and crankshaft sprocket timing marks. 3. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose. 1. Crankshaft sprocket 2. Water pump sprocket 3. Camshaft sprocket 4. Tensioner pulley >> B << TIMING BELT TENSION ADJUSTMENT 1. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4-1/2 turn, and use the force of the tensioner spring to apply tension to the belt. 2. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.

Related Content:

2005 mazda 3 2 3l push rod clearance, manual book 1G FE throtle sensor, p2263 mitsubishi canter

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

Related Content:

2004 Isuzu NPR refrigerant, isuzu 4hk1 timing marks

2003 Kia Rio L4-1.6L DOHC TIMING BELT Service and Repair Manual

0

Filed Under (Kia Motors Manuals) by admin on 28-06-2012

download
REMOVAL 1. Disconnect negative battery cable. 2. Loosen power steering lock bolts and nuts accordingly and remove tension from Power Steering (P/S) and/or Air Conditioning (A/C) compressor drive belt . 3. Remove P/S and/or A/C drive belt . 4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts. 6. Remove water pump pulley. 7. Remove crankshaft pulley and timing belt guide plate. 8. Remove upper and lower timing belt covers. 9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine. 10. Check that “I” mark on intake camshaft pulley is aligned with mark on cylinder head cover and “E” mark on exhaust camshaft pulley is aligned with mark on cylinder head cover. NOTE: Do not move camshaft or crankshaft once timing marks have been correctly positioned. 11. Loosen tensioner pulley lock bolt. 12. Protect timing belt with a rag. 13. Remove tensioner pulley. 14. Remove timing belt. NOTE: Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation. INSPECTION NOTE: Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt. 1. Replace timing belt if it is contaminated with oil or grease

Related Content:

o2 Chevy Blazer check engine light code po763, crankshaft timming mark isuzu kb300, How to change kia picanto oil seals, kia picanto radiator how to remove, picanto crank seal replacement, sensor efi system kia carens

Related Content:

2002 honda accord 2 3 timing belt tension adjustment, 2003 buick lasabre serpentine belt idler pulley torque spec, 2005 audi 3 2 tdc diagram, 2006 kia sorento camshaft pulley repair manual pdf, how to replace a tensioner pulley on a 2006 mazda 5, lincoln ls crank pulley diagram, mazda 6 crankshaft tool, pulley configuration 2001 buick lesabre, Residue from serpentine bolt on smooth pulleys