misfire cylinder 3 chrysler pacifica

You search PDF repair manual about misfire cylinder 3 chrysler pacifica, if there are search results will appear below. If search results do not exist, please search by others keyword.



  misfire cylinder 3 chrysler pacifica Direct Download speed 5432 Kb/s

  misfire cylinder 3 chrysler pacifica Full Version speed 8172 Kb/s



2004 Toyota Camry Disc Brake System Service/ Repair Manual

0

Filed Under (Toyota Manuals) by admin on 13-04-2012

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram

TOYOTA TO CHEVY AND BUICK ENGINE – TURBO CHARGED INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

download
INSTALLATION INSTRUCTIONS: 1. Install the pilot bushing into the engine crank. 2. Bolt the flywheel to the engine crank using special flywheel bolts. 3. Assemble the clutch assembly and special disc to the flywheel using special clutch bolts. 4. Assemble the clutch release arm to the inside ball pivot of the bellhousing. 5. Bolt the slave cylinder to the outside of the bellhousing. 6. Test fit the bellhousing assembly over the clutch assembly and onto the engine block. 7. Place the N1430 release bearing onto the clutch arm fork. 8. Adjust the length of the slave cylinder push rod to a length that provides a minimum of 1/8″ clearance between the release bearing face and clutch fingers. 9. This test fit over the clutch assembly is primarily done for establishing the push rod length. If this procedure is eliminated, you will not have any visual inspection for verifying the push rod adjustment. 10. Remove the bellhousing assembly from the engine. 11. Bolt the bellhousing to the front of your Toyota 5 speed transmission using the original bolts. Make sure that the two dowel pins installed in the face of the 5 speed transmission are properly fitted to the Advance Adapter bellhousing. 12. Slide the new release bearing onto the Toyota bearing retainer. Make sure that there is grease in the internal cavity of the release bearing. Most new bearings are pre-lubricated. 13. With all the components in position, you can now bolt the new bellhousing assembly onto the engine block. We have provided six (6) new socket head bolts, 3/8″-16 x 1-1/2″ long for this purpose. Make sure the engine dowel pins are properly aligned with the new bellhousing dowel pin holes. DO NOT FORCE THE BELLHOUSING ONTO THE ENGINE BLOCK. Some applications may require the tip of the input shaft to be modified slightly. The bellhousing must fit evenly to the engine block. 14. With the bellhousing now in position and the slave cylinder push rod installed, you should be able to verify the clearance between the release bearing & clutch fingers. The lever should have movement of approximately 1/8″ to 1/4″. CAUTION : If you have too much clearance, you will be utilizing too much of the slave cylinder stroke and could possibly prevent you from obtaining a full clutch release. A light duty return spring attached to the clutch release arm will prevent any premature contact of the release bearing with the clutch fingers. 15. The Toyota Land Cruiser slave cylinder will replace the original Toyota slave cylinder. The Toyota truck hydraulic slave cylinder line will have exactly the same fitting size as used on the Land Cruiser slave cylinder. 16. With the new slave cylinder installed, you can now bleed the slave cylinder installation by pumping up the slave cylinder pedal. Most installations are compatible with the original Toyota master cylinder. We have encountered a few installations that require changing of the Toyota master cylinder to a smaller 3/4″ piston. If you have any type of clutch difficulty related to full disengagement of the clutch assembly, contact Advance Adapters for any updated information.

Related Content:

how to install aslave cylinder on 2007 mustang gt, 2007 mustang gt slave cylinder, PT Cruiser Clutch Adjustment, looking for push type slave cylinder adapter kit for small block chevy, how to install dowell pins, dowel compressor, chevy rod bearing fitting and installation, blue print of 2007 mustang gt clutch sistem, 85 Bronco 2 clutch slave Cylnder, 2008 pt cruiser clutch pedal grommet

2005-2006 (LX) Chrysler 300/ Magnum/ Charger/ Pacifica Multiple Cylinder Misfire Or Rough Idle Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 01-06-2012

download
REPAIR PROCEDURE: VALVE ROTATION: 1. Relieve the fuel pressure. Refer to the detailed service information available in TechCONNECTunder: Service Info>14-Fuel System>Fuel Delivery >Standard Procedure>Fuel System Pressure Release Procedure. 2. Remove upper intake manifold. Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Manifolds>Intake Manifold> Removal. 3. Remove cylinder head cover(s). Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Cylinder Head>Cylinder Head Cover(s) >Removal. 4. Remove rocker arm and shaft assembly. Refer to the detailed service information available in TechCONNECT under: Service Info >9-Engine>Cylinder Head> Rocker Arm/Adjuster Assembly >Removal). 5. Clean and mark the tip of each exhaust valve stem at the 12 O’clock position witha paint marker. The paint mark will be used later to assist with determining the amount of valve rotation. 6. Remove the sparkplugs. 7. Rotate the crankshaft clockwise, until the number 1 piston is at Top Dead Center (TDC) on the compression stroke. 8. Install the compression tester sparkplug adapter in cylinder#1 sparkplug hole. With air hose attached to sparkplug adapter, apply 620.5 to 689 kPa (90 to 100 psi) air pressure. This is to hold valves into place while servicing components. 9. Using Tool MD 998772A (1) with adapter 6527 (4) or equivalent, slightly compress the exhaust valve spring to release tension against the valve and valve spring retainer ( Fig. 1 ). 10. Remove the valve spring retainer locks and discard the locks. NOTE: It is important that the valve rotation section of this repair procedure be performed.

Related Content:

2005 pacifica repair manual, 2006 chrysler 300 misfire, replace main thermostat chrysler 300 06 2 7

1999 Ford Escort/ Tracer Cylinder Head Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-04-2012

download
Removal 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. WARNING: Fuel supply lines will remain pressurized for long periods of time after engine shut down. This pressure must be relieved before disconnecting any fuel lines or fuel system components. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Remove the engine air cleaner outlet tube. For additional information, refer to Section 303-03 . 4. Remove the timing belt. For additional information, refer to Timing Drive Components—Timing Belt in this section. 5. Remove the vacuum hoses at the: * positive crankcase ventilation (PCV) valve (6A666). * throttle body (9E926). * intake manifold (9424). * fuel pressure sensor. 6. Disconnect the fuel charging wiring (9D930) electrical connectors at main engine connector. 7. Disconnect the crankshaft position (CKP) sensor electrical connector. 8. Disconnect the fuel line. For additional information, refer to Section 303-04 . 9. Remove the power steering pump (3A674) and bracket as an assembly. For additional information, refer to Section 211-02 . 10. Remove the generator (GEN). For additional information, refer to Section 414-02 . 11. Remove the oil level indicator tube (6754). For additional information, refer to Oil Level Indicator and Tube in this section. 12. Disconnect the heater hoses. For additional information, refer to Section 412-02 . 13. Lower the vehicle. 14. Disconnect the upper radiator hose (8260) from the thermostat housing water hose connection. For additional information, refer to Section 303-03 . 15. Remove the camshafts (6250). For additional information, refer to Camshaft in this section. 16. Remove the ignition coil (12029) and bracket. For additional information, refer to Section 303-07 . 17. Remove the water thermostat housing. For additional information, refer to Section 303-03 . 18. Disconnect the knock sensor electrical connector. 19. Remove the generator bracket-to-cylinder head bolt. 20. Remove the bolts and the cylinder head (6049). 21. Remove the cylinder head gasket and discard. Installation WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and may be ignited, resulting in possible personal injury. 1. CAUTION: Do not use abrasive grinding discs to remove gasket material; use only plastic manual scrapers. Do not scratch or gouge the aluminum sealing surfaces. Clean all gasket material from the mating surfaces on the cylinder head and cylinder block. Clean out the bolt holes in the cylinder block. Inspect the cylinder head for flatness. For additional information, refer to Section 303-00 . 2. Install a new head gasket on the cylinder block. 3. CAUTION: Do not attempt to install the cylinder head assembly without assistance. Installation of the cylinder head assembly requires two people or possible injury may occur. CAUTION: The bolts are torque-to-yield and must be replaced or engine damage may occur. Tighten the bolts in three stages in the sequence shown. * Stage 1: Tighten the bolts to 15-25 Nm (12-18 lb-ft). * Stage 2: Tighten the bolts to 35-45 Nm (26-33 lb-ft). * Stage 3: Tighten the bolts an additional 105 degrees. 4. Install the generator bracket-to-cylinder head bolt. * Tighten to 20 Nm (15 lb-ft). 5. Connect the knock sensor electrical connector. 6. Install the thermostat housing. For additional information, refer to Section 303-03 . 7. Install the ignition coil and bracket. For additional information, refer to Section 303-07 . 8. Install the camshafts. For additional information, refer to Camshaft in this section. 9. Connect the upper radiator hose. For additional information, refer to Section 303-03 . 10. Raise and support the vehicle. For additional information, refer to Section 100-02 . 11. Install the heater hoses. For additional information, refer to Section 412-02 . 12. Install the generator and bracket assembly. For additional information, refer to Section 414-02 . 13. Install the power steering pump and bracket assembly. For additional information, refer to Section 211-02 . 14. Connect the fuel lines. For additional information, refer to Section 310-00 . 15. Connect the crankshaft sensor electrical connector.

Related Content:

fleetwood sedona manuals, Honda Civic 2003 number #3 Cylinder pattern, 4 8 head bolt tightening sequence, Workshop Manual (WSM) Section 303-04, 2001 mitsubishi 3 0 cylinder torque specs, workshop information system saab, where is the knock sensor on a 2006 toyota tundra 4 7 v-8 truck, trailblazer front frame section, throttle postioning system in ford five hundred, 02 explorer 4 0 no compression on 6 cylinder

1996 Nissan Altima GLE TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Nissan Manuals) by admin on 24-02-2011

download
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables. 2. Remove front exhaust tube. Remove intake manifold collector supports, and intake manifold. Remove exhaust manifold with catalytic converter. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. Remove injectors and fuel rail as an assembly. Remove distributor cap and spark plugs. 3. Set cylinder No. 1 at TDC of compression stroke, ensuring marks on crankshaft pulley and front cover align, and distributor rotor points to spark plug wire No. 1 on cap. Remove cylinder head cover. Remove distributor. 4. Prevent camshafts from turning, and remove camshaft sprocket bolts. Remove camshaft sprocket. See Fig. 13 . Mark and remove camshaft bearing caps in reverse order of installation. See Fig. 16 . Remove camshafts. 5. Loosen cylinder head bolts in 2 or 3 steps, in reverse order of tightening sequence. See Fig. 11 . Remove camshaft sprocket cover. Remove outer (upper) chain tensioner and guide. Remove outer timing chain. Remove idler sprocket bolt. Remove cylinder head. 6. Remove oil pan and oil strainer. See OIL PAN. Remove accessory drive belts. Remove A/C compressor idler pulley (if equipped). Remove crankshaft pulley. Remove front cover. Remove chain tensioner, tensioner arm and chain guides. Remove inner (lower) timing chain and idler sprocket. Remove oil pump drive spacer and crankshaft sprocket. Inspection 1. Inspect chain roller links. Replace chain if roller links are cracked or worn. Inspect cylinder head and cylinder block mating surfaces for warpage. If warpage exceeds specification, machine cylinder head. See CYLINDER HEAD under ENGINE SPECIFICATIONS. 2. If machining reduces cylinder head height to less than specification, replace cylinder head. After machining, rotate camshaft by hand. Replace cylinder head if camshaft does not rotate freely.

Related Content:

1997 altima cam timing, cummins n14 cylinder heads, how to disable child licks on 2013 GMC terrain, how to replace cilinder head in1 8 toyota, how to top overhaul peugeot 206, is timing set on compresson stroke 2000 2 0 vw beetle, procedure on removal fo cv axle in 2005 volvo s40 2 4i, removing ih1066 cylinder liners, slk230 head removal, toyota head removal v6

2001 Pontiac Sunfire L4-2.2L VIN 4 Cylinder Head Removal And Installation Manual

0

Filed Under (Pontiac Manuals) by admin on 11-06-2012

download
Cylinder Head Replacement * Tools Required * J28467-360 Engine Support Fixture * J36660-A Torque Angle Meter. Removal Procedure 1. Disconnect the negative battery cable. 2. Relieve the fuel system pressure. 3. Drain cooling system . 4. Remove the alternative fuel module assembly. Remove the drive belt . 5. Remove the air cleaner outlet duct and resonator assembly. 6. Support engine using floor jack and block of wood. 7. Remove the engine mount . 3. Remove the intake manifold . 9. Remove the exhaust manifold 10. Disconnect the Engine Coolant Temperature Sensor ( ECT ) electrical connection. 11. Remove the valve rocker arm cover. Important: When removing valve train components keep them in order. Do this to ensure that the components are installed in the same locations and with the same mating surfaces as when removed. 12. Remove the rocker arms and pushrods. 13. Remove the generator. 14. Remove the generator rear brace. 15. Remove the power steering pump. Position the pump aside with the lines attached. 16. Remove the radiator inlet pipe. 17. Remove the ignition coil assembly. 18. Remove the accessory bracket. 19. Disconnect the secondary ignition wires from the spark plugs . 20. Remove the cylinder head bolts. 21. Remove the cylinder head. 22. Clean the following components: * Head gasket surface * Valve rocker arm cover gasket surface * Threads Installation Procedure Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin

Related Content:

01 sunfire head gasket, 2004 kia sorento head gasket, rig master cobrahead pdf, kancil cylinder head torque, 02 Buick rendezvous head gasket install you tube, installing 400 pontiac heads, i changed the head gasket on my 2005 buick rendezvous now motor is shaking, labor time 2002 f150 head gaskets, how to replace saab 93 turbo head gasket, pontiac 7k3 heads

1996 Ford Bronco/F-Series Clutch Hydraulic Line REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 30-04-2012

download
Clutch Hydraulic Line Removal 1. Note the routing of the clutch slave cylinder to clutch master cylinder tube (7A512) line from clutch master cylinder (7A543) to the clutch slave cylinder. 2. Remove retainer pin from clutch master cylinder holding clutch slave cylinder to clutch master cylinder tube in place. 3. Raise the vehicle and install suitable safety stands. 4. Disconnect clutch slave cylinder to clutch master cylinder tube from external clutch slave cylinder. On vehicles equipped with concentric clutch slave cylinders, remove tube using Clutch Coupling Tool T88T-70522-A. Installation 1. Follow the removal procedures in reverse order. 2. Bleed system. Refer to appropriate clutch hydraulic system bleeding procedure in the Adjustments portion of this section.

Related Content:

how to replace mazda bt50 chain tension

1996 Ford Bronco/ F-Series Clutch Hydraulic Line REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 08-02-2012

download
Clutch Hydraulic Line Removal 1. Note the routing of the clutch slave cylinder to clutch master cylinder tube (7A512) line from clutch master cylinder (7A543) to the clutch slave cylinder. 2. Remove retainer pin from clutch master cylinder holding clutch slave cylinder to clutch master cylinder tube in place. 3. Raise the vehicle and install suitable safety stands. 4. Disconnect clutch slave cylinder to clutch master cylinder tube from external clutch slave cylinder. On vehicles equipped with concentric clutch slave cylinders, remove tube using Clutch Coupling Tool T88T-70522-A. Installation 1. Follow the removal procedures in reverse order. 2. Bleed system. Refer to appropriate clutch hydraulic system bleeding procedure in the Adjustments portion of this section. Hydraulic Clutch Control System, 4.9L, 5.0L and 5.8L Gasoline Engines with Mazda R2 and S5-47 ZF Light-Duty and 7.3L and 7.5L S5-47 ZF Heavy-Duty Transmissions

Related Content:

1997 f-150 slave cylinder bleeder, 1997 f-150 bleed slave cylinder, diagram of clutch fluid lines on 92 s-10, ford escort 1992 hydrolic clutch manual, ford escort master cylinder diagram, ford f650 clutch adjustment, how to repalce master clutch cylinder on 98 S10, how to replace 2003 saturn ion brake master cylinder, howto put clutch in a 1997 ford explorer, remove hydraulic line from clutch slave cylinder from 04 cavalier

2009 Ford Escape 3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/ THUMP NOISE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 25-01-2012

download
3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/THUMP NOISE This article supersedes TSB 09-11-6 to update the b. Isolate noise to LH – Listen to the cylinders Service Procedure and Part List. 4 and 6 valve cover fasteners (number 6 is by the coolant pump). There will be a ISSUE significant difference in transmitted noise Some 2009 Escape and Mariner vehicles, equipped between the cylinder 4 and 6 fasteners with 3.0L engine, may exhibit an intermittent when noise is present. Noise from LH – go knocking or thumping type noise from the cylinder to Step 4. head. After engine temperature reaches 210-220 °F NOTE (99-104 °C), the noise is typically heard from the THE RH AND LH NOISES HAVE DIFFERENT rear of the engine as the vehicle comes to a stop. CAUSES. FOLLOW ALL STEPS CAREFULLY FOR An example would be coming to a stop at the end PROPER DIAGNOSIS AND REPAIR. of a highway exit ramp. Noise will continue 45-60 seconds and then diminish. Noise will occur again 3. Replace the RH cylinder head per Workshop once engine reaches 210-220 °F (99-104 °C) and Manual (WSM), Section 303-01B. vehicle comes to another stop. a. Verify repair by repeating Step 2. If noise is ACTION still present then proceed with normal Follow the Service Procedure steps to correct the engine NVH diagnostics per WSM, Section condition. 100-04. SERVICE PROCEDURE 4. Remove LH valve cover. Refer to WSM, Section 303-01. 1. Is noise a 45-60 second knock/thump from a hot engine as the vehicle comes to a stop? a. Rotate the engine clockwise until cylinder number 6 exhaust cam lobes are pointing a. Yes – Go to Step 2. up and valves are fully closed. Exhaust camshaft needs to be left in this position for b. No – Stop as this procedure does not apply. all bearing caps in Step 4b. (Figure 1) Proceed with normal Workshop Manual (WSM), Section 100-04 diagnostics. 2. Using Chassis Ears, isolate the noise to Right Hand (RH) (Bank 1) or Left Hand (LH) (Bank 2) cylinder head. Noise is typically heard as 45-60 second knock/thump as the vehicle comes to a stop after engine reaches 210-220 °F (99-104 °C). a. Isolate noise to RH – Listen to the cylinder head by the variable camshaft timing (VCT) solenoid connectors. There will also be a vibration felt at the VCT solenoid connector when noise is present. Noise from RH – go to Step 3.

Related Content:

02 kia rio 1 5 will idle no accelaration, 2013 f-150 click noise at stop and start, causes of ford escape 2001 engine vibration, 2005 tundra tailgate noisey, torkconver repire, chevy silverado catalytic converter 2004 v6 knocking tapping noise, Ford Escape motor mount removal and installation how to, GMC noise when brakes applied or released, how do i change the VCT solenoids on 2009 ford escape, installing engine in a 2008 ford escape

Ford Mustang GT Stainless Steel longtube headers Installation instructions

0

Filed Under (Uncategorized) by admin on 06-12-2011

download
Installation instructions: 1.) Open hood and disconnect negative battery cable from battery. 2.) Remove air box assembly from driver side of engine compartment to provide needed space to install header tubes. 3.) Raise and support vehicle on a suitable lift as per lift instructions. 4.) Disconnect all four oxygen sensor electrical harness connectors and remove sensors from exhaust system with a 7/8 wrench. Mark each sensor so as to enable reinstallation in the same location. 5.) Remove all fasteners and clamps attaching stock H-pipe to exhaust manifolds and over-axle pipes. Remove H-pipe from vehicle. 6.) Remove all fasteners (nuts and studs) attaching exhaust manifolds to cylinder heads and remove manifolds from engine. 7.) Loosely assemble passenger side header on the ground or bench top to obtain a mental picture of the relationship of the header tubes to each other and the collector. 8.) Disassemble header assembly and load passenger side header tubes into the car from bottom of engine. Do not bolt any tube to cylinder head until you are able to get all four into approximate position. Exercising patience during this step will help to prevent scratching the header coating. 9.) Attach passenger side header tubes to cylinder head using stock gaskets and supplied 8mm header bolts but do not fully tighten until last step. Be sure to use supplied anti-seize compound on bolt threads. 10.) Apply a thin coat of Permatex Ultra Copper high-temp silicone to inside of collector slip joints æ of the way to the bottom and install collector over ends of header tubes with oxygen sensor bung facing driveshaft. Use your finger to evenly spread sealant. 11.) Install supplied 1/4″ hardware into tabs on collector and corresponding header tubes. Do not tighten fasteners until last step of installation. 12.) Proceed to driver side. 13.) Loosely pre-assembly header assembly as before to obtain a mental picture of tube positions relative to each other then disassemble. 14.) Feed the number 2 header tube between steering column and frame and into its approximate installed position. You will need the assistance of a pry bar to accomplish this as the flange is slightly too large to pass through this point without doing so. 15.) Working through the top of engine compartment, install the number 1 header tube into position with the number two header tube. Now attach both header tubes to cylinder head with stock gaskets and supplied fasteners but do not fully tighten until last step. 16.) Install number 3 and number 4 tubes into position from underneath vehicle and attach to cylinder head with supplied fasteners; do not fully tighten until last step. 17.) Apply a thin coat of Permatex Ultra Copper high-temp silicone to inside of collector slip joints æ of the way to the bottom and install collector over ends of header tubes with oxygen sensor bung facing driveshaft. Use your finger to evenly spread sealant. 18.) Install pre-catalyst oxygen sensors into header collectors and connect to electrical harness with supplied harness extensions. 19.) If you are installing headers with a Bassani “X” style crossover pipe, install the crossover pipe as per the included instructions. The two oxygen sensor bungs included with these headers can to be used to install these headers with any custom fabricated mid-pipe assembly if you choose to not install a direct fit, Bassani off-road or catalyzed “X” style crossover pipe. 20.) Connect rear oxygen sensors installed in Bassani crossover pipe to electrical harness with supplied extensions. It will be required to trim off index lugs from male side of O2 sensor connectors to enable insertion into mating female connector of extension. 21.) Tighten all fasteners on left and right header assemblies. 22.) Reinstall air filter housing assembly and reconnect negative battery cable

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram