Skip to content

mitsubishi lancer 1994 4g15 carburettor service manual

You search PDF repair manual about mitsubishi lancer 1994 4g15 carburettor service manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Mitsubishi Lancer O-Z Rally TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
Fig. 79: Aligning Timing Belt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow. 4. Temporarily tighten the tensioner pulley bolt. 5. Remove the timing belt. Fig. 80: Tightening Tensioner Pulley Bolt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. INSTALLATION SERVICE POINTS >> A << TIMING BELT INSTALLATION CAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction. CAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position. 1. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Then temporarily tighten tensioner bolt. Fig. 81: Adjusting Timing Belt Tensioner Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Align each of the camshaft and crankshaft sprocket timing marks. 3. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose. 1. Crankshaft sprocket 2. Water pump sprocket 3. Camshaft sprocket 4. Tensioner pulley >> B << TIMING BELT TENSION ADJUSTMENT 1. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4-1/2 turn, and use the force of the tensioner spring to apply tension to the belt. 2. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.

1994 Chevy Truck C 1500 Truck 2WD Tune-up and Engine Performance Checks/ Ignition-Timing Connector Location Change Manual

download
SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1)

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

Single Speed Axle Service Manual

download
Figure 1-1 Spicer axles are identified with a manufacturing date and complete part numbers stamped on the right- hand tube. The part number may also appear on a metal tag attached to the cover plate by the cover screws, depending upon the requirements of the vehicle manufacturer. The part number, consisting of six digits reading from left to right, is the basic number for identifying the particular axle assembly. The seventh digit following the dash will identify ratio, differential, and end yoke options used in the assembly. The next group of numbers is the manufacturing date of the axle and is interpreted as follows. The first number is the month, the second number is the day of the month, the third number is the year, the fourth is the line that built the axle, and the letter is the shift. NOTE It is recommended that when referring to the axle, the complete part number and build date be obtained. To do this, it may be necessary to wipe or scrape off dirt, etc., from the axle housing. If the axle is unique on design such that the unit cannot be identified in the standard manner as described above, refer to the vehicle manufacturer’s service and/or parts manual for proper identification. SERVICING COMPONENTS NOT COVERED IN THIS MANUAL Service procedures for some components may not be covered in this manual because they are unique to the vehicle application. Refer to the vehicle manufacturer’s service manual for servicing those components. (e.g. brakes, hubs, rotors, and wheel end components). VEHICLE STORAGE OR PROLONGED INOPERATION If the vehicle has not been operated on a regular daily basis, it is recommended that the vehicle be operated at least once every two weeks. The vehicle should be moved far enough to cause the drivetrain components to make several complete revolutions. This procedure will help assure that all internal components receive adequate amount of lubrication to help reduce component deterioration caused by an undesirable environment (e.g. high humidity).

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays