altima white smokes exhaust 2002 3

You search PDF repair manual about altima white smokes exhaust 2002 3, if there are search results will appear below. If search results do not exist, please search by others keyword.



  altima white smokes exhaust 2002 3 Direct Download speed 5432 Kb/s

  altima white smokes exhaust 2002 3 Full Version speed 8172 Kb/s



Test Guidelines for Use of Essential Tool J 41413-200 Evaporative System Tester

0

Filed Under (More Manuals) by admin on 17-01-2012

download
Non-Enhanced EVAP System Diagnostic Procedure 1. Pinch off or plug the EVAP vapor line to seal the EVAP system. 2. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground. 3. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part number. 4. Connect the EEST’s nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter. 5. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE. 6. Use the remote switch to introduce smoke into the EVAP system for 60 seconds. Important: Additional smoke may need to be introduced at 15-second intervals until the leak source has been located. 7. Inspect the entire EVAP system for exiting smoke using the high intensity white light (J 41413-SPT). Enhanced EVAP System Leak Detection Procedure When diagnosing DTCs P0440, P0442, P0446 and P0455, use the J 41413-200 EEST along with 1. Turn ON the ignition with the engine OFF. 2. Command the EVAP vent valve closed with a scan tool.* *Prizm: In order to seal the EVAP system on the 1998-2002 Prizm, bypass the EVAP canister by connecting the fuel tank vapor hose to the canister purge line. Refer to the Service Information for additional information. 3. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground. 4. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part number. 5. Connect the EEST’s nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter. 6. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE. 7. Use the remote switch to introduce smoke into the EVAP system. 8. Use the J 41413-VLV EVAP Port Vent Fitting tool to open the EVAP service port (if equipped) until smoke is observed. 9. Remove the J 41413-VLV EVAP Port Vent Fitting tool once smoke is observed. Important: Additional smoke may need to be introduced at 15-second intervals until the leak source has been located.

Related Content:

gmc sonoma Air bypass solenoid location, 2010 ford escape fuel vapor canister purge valve location, car engine evaporator location 1999 exploxer, wher is the purge valve located on 2005 GMC 1500 SIRREA PICKUP, purge control valve for a 2009 chevy traverce, 1998 s10 evap routing, cleaning mazda 3 evap solenoid, ML320 engine repair manual, evap system diagram pontiac 2006 g6 gtp, how do you remove the evap canister from an xterra

2000-2004 TOYOTA ECHO VEHICLE WIRING INFORMATION

0

Filed Under (Toyota Manuals) by admin on 21-05-2011

download
WIRING INFORMATION 2002 Toyota Echo WIRE WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE/RED and WHITE/BLUE Ignition Harness 12V IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness When installing a remote start, the second ignition wire (BLACK/RED) must be isolated from the key switch ACCESSORY WIRE WHITE/BLUE Ignition Harness STARTER WIRE BLACK Ignition Harness PARKING LIGHTS (+) GREEN At Headlight Switch POWER DOOR LOCK (-) BROWN/YELLOW Harness In Passenger’s Kick Panel POWER DOOR UNLOCK (-) GREEN/BLACK Harness In Passenger’s Kick Panel DOOR TRIGGER (-) RED/WHITE At Top Of Fuse Box TRUNK TRIGGER (-) RED/BLUE Harness In Driver’s Kick Panel FACTORY ALARM ARM Arms with lock FACTORY ALARM DISARM Disarms with unlock TACHOMETER BLACK At Diagnostic Plug Under Driver’s Side Of Dash BRAKE WIRE (+) GREEN/WHITE At Brake Pedal Switch HORN TRIGGER (-) WHITE/RED Harness At Steering Column LEFT FRONT WINDOW UP RED At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN GREEN At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN GREEN/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN GREEN/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION 2003 Toyota Echo WIRE WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE/RED and WHITE/BLUE Ignition Harness 12V IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness When installing a remote start, the second ignition wire (BLACK/RED) must be isolated from the key switch ACCESSORY WIRE WHITE/BLUE Ignition Harness STARTER WIRE BLACK Ignition Harness PARKING LIGHTS (+) GREEN At Headlight Switch POWER DOOR LOCK (-) BROWN/YELLOW Harness In Passenger’s Kick Panel POWER DOOR UNLOCK (-) GREEN/BLACK Harness In Passenger’s Kick Panel DOOR TRIGGER (-) RED/WHITE At Top Of Fuse Box TRUNK TRIGGER (-) RED/BLUE Harness In Driver’s Kick Panel FACTORY ALARM ARM Arms with lock FACTORY ALARM DISARM Disarms with unlock TACHOMETER BLACK At Diagnostic Plug Under Driver’s Side Of Dash BRAKE WIRE (+) GREEN/WHITE At Brake Pedal Switch HORN TRIGGER (-) WHITE/RED Harness At Steering Column LEFT FRONT WINDOW UP RED At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN GREEN At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN GREEN/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN GREEN/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

2004 chevy traiblazer drivers side front axle seal, 08 silverado driver door wire harnes, wanted driverside wire harnes for 2008 pontiac torrent, the cable under the front light of the car is detached, Differential Seal for 2004 Trailblazer, Mazda 2012 Ignition Lock Cylinder, no black smoke from 3406b, post ignition power source 2008 gmc sierra, recoding chevrolet silverado ignition, replacement resistor for dodge ac

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

0

Filed Under (Chevrolet Manuals) by admin on 29-12-2011

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

Related Content:

2005 taurus exhaust system diagram, 2 2 s10 exhaust flange bolts, diagram of an exhaust system on a 2003 gmc envoy, Diagram of a exhaust crossover pipe for a 95 Oldsmobile aurora, 04 pacifica parts diagram, pontiac sunfire gt exhaust system diagram, how tight should exhaust, gmc yukon exhaust manifold diagram, broken rivet bolts on suburban catalytic converter, 454 exhaust donut installation

2000-2006 TOYOTA TUNDRA VEHICLE WIRING INFORMATION

0

Filed Under (Toyota Manuals) by admin on 22-05-2011

download
WIRING INFORMATION: 2000 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 2001 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Doo

Related Content:

Blue Point Eecr2 Manual, 2003 chevy silverado instrument cluster ground wire, google com/wire harness repair 2007 impala, blue piont EECR2 manual, 2006 Tundra trailer wiring, toyota pbt-gf15, trailer hitch pbt gf15, tachometer wire 2001 impala, youtube show wiring harness for 4500 ford tractor 1960\s, honda crv 2000 central locking wiring diagram

1996 Ford Truck E 350 Exhaust Manifold – Exhaust Leaks Service Manual

0

Filed Under (Ford Manuals) by admin on 08-02-2012

download
SERVICE PROCEDURE NOTE IF THE MANIFOLD IS TO BE RESURFACED, THE BOLTS MUST BE SHORTENED TO ACCOMMODATE THE EXHAUST MANIFOLD . THE BOLTS SHOULD HAVE THE LEADING “DOG POINT” REMOVED TO PREVENT BOTTOMING INTO THE HOLE. NOTE THERE SHOULD NOT BE ANY TYPE OF GASKET USED BETWEEN THE EXHAUST MANIFOLD AND THE CYLINDER HEAD. Parts Block OTHER APPLICABLE ARTICLES: NONE SUPERSEDES: 97-26-23 WARRANTY STATUS: Eligible Under The Provisions Of Bumper To Bumper 1. If an exhaust leak exists at the exhaust manifold due to a reduction in bolt torque, remove the manifold bolts and the exhaust manifold and check the overall flatness of the manifold. The manifold should not exceed 0.25 mm (0.010″) out- of-flat. Refer to the appropriate model/year Service Manual for manifold removal procedures. 2. If the vehicle is covered under the emissions warranty period, replace the manifold if it is out-of-flat. If the vehicle is out of the emissions warranty period, resurface the exhaust manifold 3. Install the manifold using new mounting hardware, but DO NOT USE WASHERS TO INSTALL THE MANIFOLD. Torque the bolts to 34-47 N.m (25- 35 lb-ft). 4. Check all exhaust system fittings loosened during repair for adequate tightness and allow engine to warm up. Recheck exhaust system for leaks and repair as required.

Related Content:

ford 5 4L water jacket leak spark plug hole intake gasket, 2001 ford excursion water leak on back of motor, metal mesh hanging loose under escort zx2, volvo d12 exhaust manifold bolt torque, replace a front exhaust manifold 2004 ford escape 24 valve, isuzu npr 5 7 water pump bolt torque, oil pan gasket on volvo ved12, schematic of a 2005 chrysler exhaust system, volvo penta 125 exhaust manifold bolt torques, what parts are required to replace the exhaust from the manifold on back for a 1990 ford f150

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT (3.1 L) MANUAL

0

Filed Under (Pontiac Manuals) by admin on 08-05-2012

download
THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) Fig. 74: Radiator Inlet Hose & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. Fig. 75: Water Outlet Housing & Bolts Courtesy of GENERAL MOTORS CORP. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces Fig. 76: Thermostat & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the thermostat. 3. Install the water outlet housing bolts. Tighten Tighten the water outlet housing bolts to 25 N.m (18 Ib ft). 4. Install the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) . 5. Install the radiator inlet hose to the water outlet housing.

Related Content:

replacing thermostat izusu axiom, 2001 oldsmobile alero 3 4l thermostat removal, where is the thermostat in a sienna 2005, how do you change a intake gasket on a 2001 pontiac grand prix gt, Car Thermostat Diagrams 2008 Pontiac G6, 99 explorer changing thermostat, 2002 pontiac grandprix 3 8 thermostat replacement, 2002 concorde themostat diagram, 2001 pontiac grand prix gt repair manual pdf, where is thethermostate on a pontaic mini van

2007-2009 Toyota FJ Cruiser Banks Monster Exhaust System Installation Manual

0

Filed Under (Toyota Manuals) by admin on 06-04-2012

download
1. Before starting work, familiarize yourself with the installation procedure by reading all of the instructions. 2. The exploded view (Figure 2) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction. 3. Throughout this manual, the left side of the vehicle refers to the driver’s side, and the right side to the passenger’s side. 4. Disconnect the negative (ground) cable from the battery (or batteries, if there are two) before beginning work. 5. Route and tie wires and hoses a minimum of 6″ away from exhaust heat, moving parts and sharp edges. clearance of 8″ or more is recommended where possible. 6. When raising the vehicle, support it on properly weight-rated safety stands, ramps or a commercial hoist. Follow the manufacturer’s safety precautions. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the front wheels are centered squarely on the topsides; put the transmission in park; set the hand brake; and place blocks behind the rear wheels. Caution! Do not use floor jacks to support the vehicle while working under it. Do not raise the vehicle onto concrete blocks, masonry or any other item not intended specifically for this use. 7. During installation, keep the work area clean. Do not allow anything to be dropped into intake, exhaust, or lubrication system components while performing the installation, as foreign objects will cause immediate engine damage upon start-up. Tools Required: • 1? 2 ” and 3? 8 ” drive ratchets with standard and metric sockets and 1 ? 2 ” and 3? 8 ” drive extension • Standard and metric combination or open-end wrenches • Standard screwdriver • Clean shop towels or rags • Pry-bar Highly recommended tools and supplies: • Foot-pound torque wrench • Penetrating oil or light lubricant spray General Installation Practices 97083 v.2.0 3 Monster Exhaust SySTEM INSTallaTIoN 1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post. 2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground. CaUTIoN: Do NoT WoRK UNDER aNy VEHIClE SUPPoRTED oNly By a JaCK. SEVERE INJURy May RESUlT. 3. From under the vehicle remove the factory exhaust starting at the 2-bolt flange in front of the muffler. Remove the two (2) bolts, two (2) washers, and two (2) springs from the flange and retain for re-use. NOTE: Remove the factory gasket from the 2-bolt flange. The exhaust system will be hanging by the exhaust hanger pins. 4. Liberally apply an aerosol lubricant on all the hanger pins. Remove the exhaust system from the vehicle by removing each hanger pin from the rubber grommet. NOTE: Remove hanger pins from the front of the vehicle to the rear. 5. Drop the exhaust system to the floor and move out of the way. You will not be reusing any components from the exhaust system. 6. Install the Banks conical gasket onto the vehicle’s 2-bolt flange. 7. Install the hanger pin on the intermediate pipe into the corresponding rubber grommet. Install the Banks intermediate pipe onto the factory 2-bolt intermediate pipe outlet using the factory hardware. See Figure 1. When tightening the

Related Content:

bosch vp44 service manual, show me a picture of the diagram of an exhaust system of a Toyota matrix, Torque Wrench Instruction Manual, Toyota Exhaust Parts Diagram

Toyota ISO Adapter Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 19-05-2011

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

Related Content:

2002 toytoa camry tank vent valve, toyota 4af engine repair manual, 1998 toyota A245E automatic transmission rebuild manual, 2002 toyota tundra 4 wheel drive suspencion, p67-y toyota vitz, diagram of front passenger seat occupant sensors and where 2005 toyota camry located, show prado 1999 valve attached to rear brake pipe with spring, 2004 toyota highlander window diagram, 2009sienna v6 thermostadt extraction, how do you fix a sunshade on toyota avalon

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

0

Filed Under (Infiniti Manuals) by admin on 17-02-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

99 hyundai ecm fuse location, Free 2002 BMW Service Manual, 2002 saturn sl owners manual, 2002 Ford Windstar Repair Manual, 2002 saturn vue repair manual free, 2002 taurus ecm removal, saturn 2002 l300 maf volts, 2002 vw passat repair manual, hino dutro vnt circuit open, 2001 pontiac sunfire P0502

2003 Chevrolet Chevy K Silverado Exhaust Popping/Snapping Noise When Vehicle is Hot, at Idle, or Immediately After Vehicle is Shut Off (Replace Muffler Heat Shield) Service Manual

0

Filed Under (Chevrolet Manuals) by admin on 09-02-2012

download
Follow the service procedure below to correct this condition. Important: Some popping/snapping noise from the exhaust system during cool down is a normal condition. The customer should be made aware that this service procedure is designed to reduce but not eliminate all exhaust system popping and snapping during cool down. 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. Caution: 2. Remove the nuts securing the muffler to the catalytic converter. 3. On 6.0L and 8.1L equipped vehicles only, loosen the exhaust pipe clamp. Important: Do not use oil base lubricants on the rubber exhaust hangers. 4. Apply a soapy solution to the exhaust pipe hanger rods in order to ease the removal of the exhaust hangers. 5. Pry the exhaust hangers free from the exhaust pipe hanger rods. Important: It is not necessary to remove the muffler from the vehicle to replace the muffler heat shield. 6. Reposition the muffler to gain access to the muffler heat shield 7. Using an air-powered hack saw blade, or equivalent, cut off the existing muffler heat shield just as the heat shield rises off of the muffler. See the illustration above. 8. Remove the heat shield from the muffler. 9. Hammer flush the remaining heat shield to the muffler. Important: 10. Install the new heat shield (see parts list below) onto the muffler as shown above.

Related Content:

1997 sugar sand heat repair manual, 2003 chevy silverado engine lifter replacement pdf, 2003 chevy silverado repair manual, exhaust heat shield 2002 4runner, FIESTA CATALYTIC HEAT SHIELD REMOVING, fuel tank heat shield 2009 f-150 owners manual, removing heat shields 2004 ford f150, toyota corolla 2007 shield bolts

Related Content:

gmc sonoma Air bypass solenoid location, 2010 ford escape fuel vapor canister purge valve location, car engine evaporator location 1999 exploxer, wher is the purge valve located on 2005 GMC 1500 SIRREA PICKUP, purge control valve for a 2009 chevy traverce, 1998 s10 evap routing, cleaning mazda 3 evap solenoid, ML320 engine repair manual, evap system diagram pontiac 2006 g6 gtp, how do you remove the evap canister from an xterra