Skip to content

nippondenso alternator manual

You search PDF repair manual about nippondenso alternator manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

1991 Subaru Loyale Sedan (4 Door) Camshaft And Timing Belt Repair Manual

download
Tightening torque: REMOVAL 1. Loosen water pump pulley mounting nuts or bolts. 2. Loosen two alternator mounting bolts, and detach V-belt. [Except air conditioner equipped model] 3. Remove water pump pulley and pulley cover. 4. Disconnect lead from oil pressure switch. 5. Remove oil level gauge guide together with gauge. 6. Remove crankshaft pulley. To lock crankshaft, use FLYWHEEL STOPPER [manual transmission model] or DRIVE PLATE STOPPER [automatic transmission model]. 7. Remove belt cover plate. [TURBO model] 8. Remove belt covers LH, RH and FR. 9. Removing timing belt Zoom Sized for Print (a) Loosen tensioner mounting bolts on # 1 cylinder by 1/2 turn. (b) With tensioner fully turned to slacken belt, tighten mounting bolts. (c) Mark rotating direction of timing belt, then remove belt. (d) Loosen tensioner No. 2 mounting bolts on # 2 cylinder by 1/2 turn. (e) With tensioner fully rotated to slacken belt by using TENSIONER WRENCH, tighten tensioner mounting bolts. NOTE: Cover TENSIONER WRENCH clamping tips with a rubber hose or waste cloth to prevent crankshaft or pulley from being damaged 10. Remove tensioner and tensioner No. 2 together with tensioner spring. 11. Remove belt idler. 12. Remove camshaft sprockets by using CAMSHAFT SPROCKET WRENCH. 13. Remove right-hand belt cover No. 2, left-hand belt cover No. 2 and belt cover RR. TIMING BELT 1. Check timing belt teeth for breaks, cracks, and wear. If any fault is found, replace belt. 2. Check the condition of back side of belt; if any crack is found, replace belt. A. Be careful not to let oil, grease or coolant contact the belt. Remove quickly and thoroughly if this happens. Zoom Sized for Print

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

MULTI-BATTERY ISOLATOR APPLICATION INSTALLATION MANUAL

download
PLEASE READ INSTRUCTIONS COMPLETELY PRIOR TO STARTING INSTALLATION 4 3 2 1 GROUP GROUP GROUP GROUP General Motors (Delcotron/Delphi) Except Delcotron/Delphi CS series alternators (CS series used on most 1985 and newer GM vehicles). Ford Up to 1998 Chrysler All models, all years including Nippondenso externally regulated alternators. Jeep Equipped with Nippondenso externally regulated alternators Japanese Imports With alternators using external voltage regulator or external sensing. Motorola Load Handler Series or 8EM Remote Sense Series General Motors (Delcotron/Delphi) Equipped with Delcotron/Delphi CS series (most 1985 – 1993) or CS130-D series alternators (most 1993 and newer***) Jeep Vehicles equipped with Delcotron/Delphi CS series alternator (most 1985-1990). Toyota, Honda & Some Imports 1985 and newer equipped with Nippondenso alternator with internal regulators or alternators with an “S” (sense) terminal. Motorola Other than Load Handler Series Bosch Requiring regulator sensing A Group 3 Isolator will have a colored fourth terminal indicating the “R” terminal. Unplugging the plug-in connector from the alternator and counting the number of holes in the connector can identify the CS series alternator. The CS series will have three small and one large hole. The CS130-D alternator has four pin terminals all the same size. The SI series will have two slotted holes in the connector. ***Delco/Delphi CS series alternators require a separate sense wire which is included with the connector kit. The connector kit may or may not be included with the Isolator, but is available as an accessory. All Group 2 Isolators may be used in Group 1 applications. Simply disregard the additional excitation (“E”) terminal. A Group 2 Isolator will have a colored fourth terminal indicating the “E” terminal. Battery Isolators are not compatible with these alternators. A Battery Separator is recommended for these applications. Alternators with internal voltage sensing, e. g. some Mitsubishi and Hitachi , or single wire self exciting Delco/Delphi alternators. Isolators may be used if the alternator is modified. For further information on Group 4 Isolation Technolgy contact Sure Power Industries.

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Ford Windstar 3.8L The battery light is on but the alternator is charging Service Manual

download
Procedures 1. Disconnect the alternator and the Powertrain Control Module (PCM). Check the Violet (VT) (GENerator MONitor or GENMON) wire from the alternator to pin 20 of the PCM connector and the Red/Pink (RD/PK) (GENerator COMmand or GENCOM) wire from the alternator to pin 45 of the PCM for high resistance, an open, or a short to ground. Repair the wiring as needed. 2. If the wiring checks OK, reconnect the PCM and alternator. Start the engine and monitor the VT wire for a roughly 0-10v square wave signal. The signal will be around 40-50% normally with no loads on the system and minimal charging system output. As the load increases, the duty cycle should increase (NOTE: the duty cycle is a positive duty cycle so as the duty cycle increases, the voltage high time increases). 3. If there is no signal on the wire, disconnect the alternator and with key on check the VT wire for roughly 9-10v from the PCM. If OK, jump the Orange/Light Blue (OG/LB) wire to battery voltage and recheck operation with everything connected. This wire should be battery voltage at all time. If the OG/LB wire has battery voltage, the VT wire shows voltage from the PCM but there is no signal on it with the alternator charging, suspect a faulty, defective or incorrect alternator