no enhanced dtc are presently stored in the vehicles computer

You search PDF repair manual about no enhanced dtc are presently stored in the vehicles computer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  no enhanced dtc are presently stored in the vehicles computer Direct Download speed 5432 Kb/s

  no enhanced dtc are presently stored in the vehicles computer Full Version speed 8172 Kb/s



2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

0

Filed Under (Infiniti Manuals) by admin on 17-02-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

99 hyundai ecm fuse location, Free 2002 BMW Service Manual, 2002 saturn sl owners manual, 2002 Ford Windstar Repair Manual, 2002 saturn vue repair manual free, 2002 taurus ecm removal, saturn 2002 l300 maf volts, 2002 vw passat repair manual, hino dutro vnt circuit open, 2001 pontiac sunfire P0502

1996 Pontiac Grand Am DTC P0502 Vehicle Speed Sensor (VSS) Circuit Low Input (3.1L VIN M) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 06-07-2012

download
Action Taken When the DTC Sets Conditions for Clearing the MIL/DTC Diagnostic Aids Test Description The numbers below refer to the step numbers on the diagnostic table. 2. This step verifies that the PCM is receiving a signal from the vehicle speed sensor. 3. This step verifies that there are no opens in the circuitry from the vehicle speed sensor to the PCM connector. 7. This step performs a resistance test on the VSS circuits from the PCM connector. • The transmission defaults to 3rd gear. • The PCM inhibits TCC operation. • The PCM illuminates the Malfunction Indicator Lamp (MIL). • The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported. • A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. • The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. • Check for PRNDL DTC P0705. DTC P0705 affects transmission operation. This may set DTC P0502 falsely. • Check for Electromagnetic Interference (EMI) in circuits 400 and 401. EMI may be induced if the harness is routed along the spark plug wires. • Inspect the wiring for poor electrical connections at the PCM. Inspect the wiring at the TCC brake switch. Look for the following conditions: – A bent terminal – A backed out terminal – A damaged terminal – Poor terminal tension – A chafed wire – A broken wire inside the insulation • When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. • Ensure that the VSS is securely tightened to the case extension. DTC P0502 Vehicle Speed Sensor Circuit (VSS) Low Input

Related Content:

1993 taurus EATC wiring harness, pcm 40i transmission troubleshooting, 1991 subaru loyale haynes repair manual free download, mazda obd2 reads no dtc presently stored in vehicles computer, chevy 3100 pcm malibu location, 96 town and country p1495, 7 3 Powerstroke PCM Failure Symptoms, 2002 sable pcm replace, 1996 Honda Accord PCM, vss hino

1999-2001 Infiniti Q45 MIL “ON” REAR O2 SENSOR DTC SERVICE PROCEDURE

0

Filed Under (Infiniti Manuals) by admin on 07-01-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2/4 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 1999-2001 Q45 23710-3H000, -3H001, -3H005, -3H006, -3H007 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Perform ECM Reprogramming on page 3. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. SELF-DIAG RESULTS SYSTEM ENGINE DATE 01/24/2002 5:35:07 P/N 23710-3H000 DTC Code TP020024 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 3/4 ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

2007 ecm location saturn vue, 2008 chevy 3 5 repair manual, how to replace ECU on 2005 Cadillac CTS, infiniti q45 manual torrent, mercedes cis repair manual pdf, manual pdf de hino dutro, lincoln ecm reprogramming, instructional how to reset the ECM on a 2004 Cadillac CTS, Ford 1998 E350 loction of the ecm, ecm update audi 2006 list

FORD 6.0L DIESEL CALIBRATION UPDATE VARIOUS ISSUES CALIBRATION

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
The PCM and FICM calibration update contains model years covered and Integrated Diagnostic improvement actions to address the following System (IDS) calibration level. symptoms: 2005 F-Super Duty 6.0L: ISSUE Some 2003-2007 F-Super Duty vehicles, 2003-2005 •False DTC P0470 – Exhaust pressure sensor A Excursions and 2004-2010 E-Series vehicles, circuit fault due to a freezing condition. equipped with a 6.0L diesel engine may exhibit hard •False DTC P0404 – Exhaust gas recirculation start, no start, white smoke, lack of power, running (EGR) performance due to a stuck turbocharger rough condition after cold engine start up, or condition. diagnostic trouble codes (DTCs) P0404, P0470, •Cooling loss protection – Revised engine P0611, P1260 and/or P1378 issues. Refer to the protection strategy when an engine Calibration Content for information detailing specific over-temperature condition is present. Vehicles vehicle content by vehicle application and model updated with this service calibration will display year that is being addressed by this calibration higher temperature gauge readings when high update. engine oil temperature (EOT) conditions or high engine coolant temperature (ECT) are This article includes previously released calibration encountered and may disable EGR operation to content that improves injector performance in cold prevent possible EGR cooler damage. engine operation and additional diagnostic capabilities and product protection strategy •Oil cooler efficiency monitor – DTC P012F stored enhancements. These enhancements provide and wrench warning lamp illuminated when the oil additional diagnostic capabilities, adds additional coolers efficiency drops below a specified new DTCs and engine protection strategies. Refer threshold for a given speed and vehicle load to the Calibration Content for additional details. See condition. the appropriate Powertrain Control/Emissions •Turbocharger vane sweep strategy – Performs a Diagnostic (PC/ED) manual for technical sweep of the turbocharger vanes and unison ring descriptions and diagnostic routines associated with during stationary idle conditions. Vane sweep can new DTCs. occur once per hour to help reduce turbocharger sticking. ACTION •FICM low voltage detection monitor – DTC P0560 Reprogram the powertrain control module (PCM) stored and wrench warning lamp illuminated when using IDS release 63.13 and higher or 64.01 and PCM vehicle power (VPWR) parameter identifier higher. The transmission control module (TCM) and (PIDS) is below 10.25V for 60 seconds or below fuel injector control module (FICM) , will 9V for 4 seconds. automatically update if they are not at the latest •Turbocharger over boost detection – DTC P0234 calibration level. This new calibration is not included stored and wrench warning lamp illuminated when in the VCM 2009.11 DVD. Calibration files may also a turbocharger over boost condition occurs. be obtained at www.motorcraft.com. 2006-2007 F-Super Duty 6.0L: CALIBRATION CONTENT •False DTC P0404 – EGR performance due to a Reprogram the PCM to the latest calibration stuck turbocharger condition

Related Content:

2005 town and country atc, mazda 3 transmission control module symptoms, pcm diagnostics for 6 0l, what does calibration complete mean on a 2006 buick lucerne?, what is the pcm PCM calibration code f250 6 0

1986-1988 TOYOTA PICKUP INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 17-09-2011

download
Installation of this body lift kit without proper knowledge of the factory recommended procedures might affect the performance of these components and the safety of your vehicle. It is strongly recommended that a certified mechanic who is familiar with the installation of similar components install this body lift kit. 2. Park the vehicle on a clean, dry, flat, level surface. Block the tires so the vehicle cannot roll in either direction. 3. Disconnect both battery cables. Be sure to disconnect the negative cable first, then the positive cable. 4. Before you begin lifting the vehicle, you need to measure and record the bumper to vehicle gaps and also the distance between the cab and the bed. These dimensions will allow you to retain the factory spacing at these locations. WARNING This body lift kit should only be installed on vehicles that are in good working condition. Before the installation begins, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in a collision, or misused. Off road use of your vehicle with this body lift installed may increase the stress applied to the factory body mounts. It is not recommended that any vehicle, with a body lift installed, be involved in any extreme off road maneuvers. Failure to follow this warning may result in serious personal injury and/or serious damage to your vehicle. 5. Remove the center shifter console, shift boot, and plate. Remove the doorsill plates and the kick panels. Carefully lift the carpet to expose the cab-mounting bolts. Loosen but do not remove all cab mounting bolts. 6. Carefully mark the splines on the steering shaft in the engine compartment at the steering box and steering column so that the shaft can be reinstalled in the original orientation. Remove the shaft from the vehicle. 7. Release the parking-brake- cable clip from the firewall. 8. Remove the parking brake cable from the frame clip 1 next to the battery. 9. Release the clutch line from the clip on the lower portion of the firewall. Loosen the clutch line from the clip on the firewall located behind the carburetor. Reroute the clutch line underneath the heater hose closest to the passenger side of the vehicle. 10. If the vehicle is equipped with power steering, loosen the clamp just behind the grill that holds the serpentine cooling line and push the line toward the firewall. Loosen both brackets that hold the cooler. Adjust the hoses that are attached to get more hose clearance. 11. Relocate the engine ground strap from the firewall to the lower throttle cable bolt on the firewall. 12. Automatic transmission only. Remove the transmission linkage between the steering column and the transmission. Disconnect the transfer case shifter from the “C” shaped linkage. 13. Remove the oxygen sensor wire from the clip underneath the cab and make sure there is enough slack to allow for the lift 14. Remove the front bumper and lower valance. 15. Remove the two bolts that mount the fan shroud to the radiator. Pull the fan shroud up out of the clips on the bottom of the radiator. Lay the fan shroud over the fan away from the radiator. WARNING Use extreme caution when working with the engine cooling system. Never remove the radiator cap from a hot radiator. Wait until the engine and radiator has cooled and the pressure in the system has dissipated. Use care not to spill any antifreeze/coolant while draining system. Immediately clean up any spilled fluids. Antifreeze can be harmful to the environment. Take care to store the drained antifreeze/coolant in a place away from children and animals. Antifreeze/coolant can be fatal if swallowed.

2000 Ford Pickup F250 Super Duty TEST DE: EXHAUST BACKPRESSURE (EBP) SENSOR

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine. Inspect for damaged pins, corrosion and loose wires. Repair as necessary. Measure resistance between ground and Gray/Red wire at EBP sensor wiring harness connector. See Fig. 11 . If resistance is less than 5 ohms, replace EBP sensor. If resistance is 5 ohms or more, locate and repair open circuit in Gray/Red wire. 3) Continuous DTC P0470 This DTC indicates PCM detected a EBP sensor malfunction during normal driving conditions. Possible causes for this DTC are: Faulty EBP Sensor • Faulty Connection • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. While observing EBP PID, wiggle and bend small sections of wiring harness starting at EBP sensor connector and working toward PCM. If EBP reading fluctuates, isolate fault and repair as necessary. If reading does not fluctuate, go to next step. 4) Check Connector Disconnect EBP sensor connector. Sensor is located on top front of engine. Disconnect PCM 104-pin connector. Inspect connectors for damaged pins, corrosion and loose wires. Repair as necessary. Clear DTCs and repeat QUICK TEST . If both connectors are okay, no problem is indicted at this time. 5) DTC P0471 This DTC indicates PCM detected an EBP sensor malfunction during normal driving conditions and with EBP sensor enabled. Possible causes for this DTC are: Faulty EBP Sensor. • Plugged Or Restricted Sensor Supply Tube • Damaged Exhaust Pressure Regulator (EPR) Linkage Or Butterfly Damage • Faulty PCM • Perform KOER ON-DEMAND SELF-TEST . If any DTCs are present, repair fault(s) before continuing with this test. Using scan tool, select EBP PID from PID/DATA monitor menu. Road test vehicle performing hard accelerations while monitoring EBP PID. If EBP reading increases to more than 25 psi with EBP sensor on, no problem is indicated at this time. If EBP reading does not increase to more than 25 psi, go to next step

Related Content:

2007 nissan frontier camshaft position sensor location, 02 sensor problems 2010 prius, how to check oil in front crank case 2005 tahoe, 2000 Infiniti Q45 Problems, Chevy Traverse Bank 2, range sensor on 2000 isuzu rodeo, o2 sensor bank 1 tundra, location of front heated exhaust oxygen sensor Saturn SL two 2002, locate 2011 traverse coolant temperature sensor, install cam sensor kia 05 sedona

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 06-02-2012

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock

Related Content:

IDLE RELEARN 02 CAMRY, 04 rav4 idle at 6000 rpm after battry change, 2001 malibu throttle position sensor relearn procedure, 2006 cheverolet impala will not idle, 2008 dodge grand caravan coolant fan runs continuasly, dodge caravan1997 transm autom 3 3l how connected with radiator, Dodge Cruise Control Repair 2012 caravan, IRRATIC IDLING 87 2 8 V6 BLAZER, u140f rough shifting

1998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 24-06-2012

download
An intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This test checks if communication can be established between the scan tool and the VTD. If the scan tool cannot communicate with the VTD, refer to Diagnostic System Check – Theft Deterrent in Theft Deterrent. 3. This test checks for any opens in the serial data circuit between the VCM and the VTD. This also checks for any intermittent malfunctions associated with the serial data circuit. 4. This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the VCM is disabling fuel. 7. Use a scan tool to clear and check for any DTCs in all the modules connected to the Class 2 Serial Data circuit (VCM, VTD, ATC, and BCM). the module itself. After repairing the cause of DTC P1626, clear all DTCs from the systems capable of storing this DTC and DTC U1192. 1 Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module’s data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the scan tool. 2. Turn ON the ignition leaving the engine OFF. 3. Attempt to establish communications with the VTD (Passlock) Control Module. Does the scan tool communicate with the VTD (Passlock) Control Module? — Go to Step 3 Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent 3 Check the Class 2 Serial Data circuit for the following intermittent conditions: Did you find a problem? • An open in the Class 2 Serial Data circuit between the VCM and the VTD (Passlock) Control Module. • A short to ground. • A short to voltage. • Loose or damaged terminals at the DLC, VCM or the VTD (Passlock) Control Module. — Go to Step 6 Go to Step 4 4 1. Turn OFF the ignition. 2. Connect or install any connectors or components that were disconnected or removed. 3. Clear all DTCs using a scan tool. 4. Turn OFF the ignition for 15 seconds. 5. Attempt to start the engine. Does DTC P1626 reset? — Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent Go to Step 5 5 This DTC is intermittent. Are any additional DTCs stored? — Go to the applicable DTC table Go to Diagnostic Aids 6 Repair the circuit as necessary. Refer to Wiring Repairs or Connector Repairs in Wiring Systems. Is the action complete?

Related Content:

p1626 chevy venture, 87 bonco 2 parking brake control assembly diagram, what is a class 2 malfunction, VTD? chevrolet, universal theft deterrent system for 1996 bonneville, theft deterrent module location 99 olds intrigue, hummer h3 passlock starting issue, how to reset factory lock on h3, GM Theft Deterrent System Problem, gm passlock 1 bypass instructions

2004 Ford Explorer/Mountaineer Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-05-2011

download
C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw Control Disabled ABS Module This DTC will be set if the stability assist system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment, or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test Q . C2769 (ABS only) Longitudinal Acceleration Sensor Circuit Failure ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2769 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Circuit Failure ABS Module Go To Pinpoint Test H . C2770 (ABS with Stability Assist) Longitudinal Acceleration Sensor Signal Fault ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Signal Fault ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2770 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2777 Sensor Cluster Bus Failure ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault Section 418-00 . U1901 CAN Network #2 Communication Bus Fault- Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault received from external node Network Fault Section 418-00

Related Content:

WHERE IS 2002 DAKOTA CENTRAL TIMING MODULE, ABS fault on Tahoe, hino 05 air brake fail abs, where is yaw sensor located on a 2002 ford explorer, how to replace vats module on 1997 buick lesabre, gmc hvac relearn, ford u1901 steering angle sensor, ford u1901 escape, ford relearn after abs sensor trans harsh, FORD FUSION U1900-ABS CAN Communication BUS Fault

2005 Ford F-Super Duty 250-550 Auxiliary Brake System/ Trailer Brake Control (TBC) Module Repair Manual

0

Filed Under (Ford Manuals) by admin on 14-06-2012

download
connected to the vehicle, the TBC module will enter a “sleep mode” but still continue to send a PWM voltage signal to the trailer tow connector every 4 seconds to detect when a trailer is connected. When the ignition key is in the RUN position and the module is in sleep mode, pressing a gain button or sliding the manual switch will cause the module to “wake up”. If a trailer is not connected to the vehicle, the display should prove out for 3 seconds, then the trailer icon should illuminate red and the IC message center should display TRAILER DISCONNECTED or CHECK TRAILER. If a trailer is connected to the vehicle, the display should prove out for 3 seconds and then the trailer icon should illuminate green. Inspection and Verification NOTE: A trailer brake emulator tool is available to verify that the TBC module and vehicle wiring are functioning correctly. 1. Verify the TBC system is correctly installed by checking that the vehicle is equipped with a brake pressure transducer on the master cylinder. If the brake pressure transducer is not present, then the TBC system has been erroneously installed. 2. Verify the customer concern. 3. NOTE: The TBC does not function with electric-over-hydraulic or surge trailer brake types. Verify that the trailer brakes are electric-actuated drum type brakes. 4. Verify the stoplamps operate correctly by applying and releasing the brake pedal with the ignition switch in the OFF position and the trailer disconnected. If the stoplamps do not operate correctly, refer to Section 417-01 . If the stoplamps operate correctly, proceed to the next step. 5. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Chart 6. If the cause is not visually evident, connect the scan tool to the data link connector (DLC) and select the vehicle to be tested from the scan tool menu. If the scan tool does not communicate with the vehicle: * check that the program card is correctly installed. * check the connections to the vehicle. * check the ignition switch position. 7. If the scan tool still does not communicate with the vehicle, refer to the scan tool operating manual. 8. Carry out the scan tool data link test. If the scan tool responds with: * CAN, ISO, or UBP circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 . * No response/not equipped for the TBC, GO to Pinpoint Test A . * System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out self-test diagnostics for the TBC and the antilock brake system (ABS) module. 9. If the DTCs retrieved are related to the concern, go to the Trailer Brake Control (TBC) module Diagnostic Trouble Code (DTC) Chart or Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Chart to continue diagnosis. 10. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnosis. NOTE: Always retrieve the continuous DTCs after running the self-test.

Related Content:

2005 f150 security module, 2007 ford f250 tbc fault, 2008 Ford sd brake pressure transducer, an i program a ford abs module, ford tbc fault, programming abs module ford, tbc falt on 2005 ford f350, tbc fault 2006 f250

Related Content:

99 hyundai ecm fuse location, Free 2002 BMW Service Manual, 2002 saturn sl owners manual, 2002 Ford Windstar Repair Manual, 2002 saturn vue repair manual free, 2002 taurus ecm removal, saturn 2002 l300 maf volts, 2002 vw passat repair manual, hino dutro vnt circuit open, 2001 pontiac sunfire P0502