Skip to content

oem toyota accessories installation instructions online

You search PDF repair manual about oem toyota accessories installation instructions online, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 -2008 Toyota Tacoma Tailgate Lock PL5200 Installation Instructions

download
Lock Assembly 2 Washers, 2 Nuts 2 Rod Extenders Instructions Warranty Card Tools Required: Screw Driver T-30 Torx 7 mm Socket Tech Support: Call 1-800-342-5911 Installation Instructions Tailgate Lock PL5200 Toyota Tacoma 2005 -2008 4. Turn tailgate over and put segmented washer over one of the studs 5. Screw the nut onto the stud. Repeat steps 4 and 5 on the other stud and tighten both nuts. 6. Rotate plastic rod retainer using a screw driver and remove rod. 7. 1. Insert rod into Extender slot 2. Twist Extender to retain the rod. 8. 1. Insert Extender onto arm. 2. Twist rod retainer over the Extender. 9. Repeat steps 6, 7 and 8 on the second rod to finish the installation. NOTE: If the tailgate will not open when unlocked, remove the rod extenders LIMITED WARRANTY TERMS AND CONDITIONS 1. INSTALLATION: Pop & Lock TM is not responsible for installing the Pop & Lock TM or for the harm suffered by any person as a result of installing it. 2. WARRANTIES: a) Customer acknowledges that it is unreasonable to believe that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so-called anti-theft or security device is that it will deter many theives. b) POP & LOCK TM MAKES, AND THE CUSTOMER RECEIVES, NO WARRANTY, EXPRESSED OR IMPLIED, EXCEPT THE WARRANTIES OF TITLE TO THE POP & LOCK TM AND THEIR MERCHANTABILITY, PARTICULARLY NO WARRANTY OF FITNESS FOR A PARTICULAR USE OR PURPOSE OR AGAINST INFRINGEMENT. c) As Customer’s only remedy, Pop & Lock TM will repair or replace, at its option and without charge, any lock that is defective in material or workmanship when received by the Customer and is returned to Pop & Lock TM , FOB Pop & Lock’s offices, within one (1) year after its receipt by the Customer. Pop & Lock TM will ship all replacement, or repaired locks to the Customer, FOB Pop & Lock’s shipping point.

2001-2007 Toyota Highlander MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS

download
This bracket kit fits the 2001-10 Toyota Highlander. For the ’01-’07 Toyota Highlander, follow the instructions below. For ’08-’10 Toyota Highlander instructions, see the separate section included in these instructions. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Fig.C Fig.D Fig.E 1. Start by removing four plastic fasteners that attach the grille to the core support (Fig.C). 2. Once all the fasteners are removed, squeeze and push out a square plastic clip fastener for the grille, located between the headlight housing and the radiator support frame on each side. 3. Pull back the grille and remove the Phillips screw that attaches the fascia to the hood latch support (Fig.D). 4. On each side, remove three plastic fasteners: two of the plastic fasteners are attaching the fender liner to the fascia (Fig.E); the other plastic fastener is attaching the fender liner to the frame rail (Fig.F) 5. Remove ten 10mm (head) bolts (Fig.G) and two plastic fasteners (Fig.H) attaching the lower splash shield to the fascia and the sub frame. 6. On both sides, pull back the fender liner and remove one 10mm screw attaching the corner of the fascia to the fender (Fig.I). Fig.K Plastic fastener MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 1-800-669-9690 fax 360-735-9300 KIT# 1180-1 05/14/10 KS 9. Remove the foam shock absorption core by pulling forward (Fig. L). Note: this will not be reinstalled. Retain the foam shock absorption core and attachment hardware so that it can be replaced if the bracket is ever removed. 10. Remove six 14mm (head) bolts to remove the bumper core (Fig.M). Note: this will not be reinstalled. Retain the bumper core and attachment hardware so that it can be replaced if the bracket is ever removed. 11. Remove the alignment studs at the end of each frame rail (Fig.N). 12. Now, place the main receiver brace into the ends of the frame rails (Fig.O). 13. Bolt the main receiver brace into place using the three supplied 10mm x 1.25 x 35mm bolts, flat washers and lock washers (Fig.P). Repeat for the other side. Tighten to the torque specifications listed at the end of these instructions.

TOYOTA 4RUNNER CARGO LINER (WITHOUT DOUBLE DECKER CARGO SYSTEM) INSTALLATION INSTRUCTIONS

download
Your new liner is custom molded to fit your vehicle. Upon removal from the box your liner will not completely unroll and lay flat. This is normal and only temporary. Just place the liner on the floor or in the back of your vehicle with a weight in each corner (a book works well). After about 15 minutes, your liner will remain flat. In colder climates this “relaxing” may take longer; moving the liner to a heated area will accelerate the process. Your liner is manufactured using an engineering resin that is lightweight and extremely tough and durable. The easiest way to clean your liner is with a damp cloth or sponge. If using a cleaner, 409 ® or Glass Plus ® work well. Use of Armor All ® , Son-of-a-Gun ® or similar items is discouraged as these products make the liner slick. INSTALLATION INSTRUCTIONS FOR YOUR TOYOTA 4RUNNER CARGO LINER (WITHOUT DOUBLE DECKER CARGO SYSTEM) IF YOU WISH TO ACCESS THE FACTORY CARGO HOOK TIE DOWN LOCATIONS IN YOUR 4-RUNNER WITH YOUR CARGO LINER IN PLACE, JUST FOLLOW THESE TWO EASY STEPS: 1). CAREFULLY TRIM AWAY THE MATERIAL FROM INSIDE OF THE RAISED BANDED AREAS (2 PLACES) ALONG THE FRONT WALL OF THE LINER. THESE AREAS ARE SHOWN DARKENED ABOVE. 2). MAKE A SLIT HORIZONTALLY ACROSS THE CENTER OF THE TWO SMALLER RAISED AREAS ALONG THE BACK EDGE OF THE MAT (2 PLACES SHOWN BELOW CIRCLED). ONCE THE LINER IS SLIT, THE HOOKS CAN BE PULLED UP THROUGH THE LINER. A UTILITY KNIFE OR SIMILAR TOOL WORK WELL FOR TRIMMING. USE EXTREME CAUTION WHEN HANDLING SHARP TOOLS.

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

TOYOTA 99-8100 INSTALLATION INSTRUCTIONS

download
TOYOTA Celica (GT/GTS) 1986-89 TOYOTA Celica (ST) 1986-89 2 2 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws from the lower steering column panel and remove the panel. Remove (2) screws exposed on the dash trim bezel. Open the glove box and remove (2) screws exposed. Remove (2) screws from the ashtray cavity and (2) screws from the bracket. Remove (2) screws from each side of the dash trim bezel and unclip the bezel. Remove the screws securing the factory head unit and disconnect the wiring. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws from the lower steering column panel and remove the panel. Remove (2) screws exposed on the dash trim bezel. Open the glove box and remove (2) screws exposed. Remove (2) screws from the ashtray cavity and (2) screws from the bracket. Remove (2) screws from each side of the dash trim bezel and unclip the bezel. Remove the screws securing the factory head unit and disconnect the wiring. Slide Mounting Tabs #3 and #8 into slots “B” on Bracket Set #2. The Mounting Tabs, Brackets and Bracket slots can be identified by the stamped letter on each component. Skip to the Installation Instructions for ALL VEHICLES on Page #10. Slide Mounting Tabs #8 into slots “C” on Bracket Set #2. The Mounting Tabs, Brackets and Bracket slots can be identified by the stamped letter on each component. Skip to the Installation Instructions for ALL VEHICLES on Page #10. 1 TOYOTA Pickup (double DIN) 1989-91 2 Slide Mounting Tabs #3 into slots “H” and “D” on Bracket Set #2. The Mounting Tabs, Brackets and Bracket slots can be identified by the stamped letter on each component. Skip to the Installation Instructions for ALL VEHICLES on Page #10.