Skip to content

oil leak from around oil filter on ford explorer sport trac

You search PDF repair manual about oil leak from around oil filter on ford explorer sport trac, if there are search results will appear below. If search results do not exist, please search by others keyword.

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

2003-2005 FORD Explorer Sport Trac Alignment – Irregular Front Tire Wear SERVICE PROCEDURE

download
ISSUE Some 2003-2005 Explorer Sport Trac vehicles equipped with the Goodyear Wrangler RT/S, P255/70R16 109S AT OWL tire, may exhibit signs of feathering heel-toe wear on the inside or outside edges of the front tires . Tire noise may also be present during regular highway drive or when braking. ACTION Inspect the tires for feathering heel-toe wear. It may be necessary to rotate or replace tires and reset toe. Refer to the following Service Procedure. SERVICE PROCEDURE Zoom Sized for Print 1. Visually inspect the front tire’s inside and outside shoulder ribs (Figure 1) 2. Measure the difference in tread depth of the leading edge compared to trailing edge, of the most-worn lug (figure 2). If the average difference in tread depth between leading and trailing edge is less than 2 mm, rotate the tires . If the average difference is more than 2 mm, replace the front tires. Also inspect the rear tires and replace if necessary. 3. Ensure that the camber and caster readings are within specification

1997-2006 Ford Explorer Sport 2-dr Overhead Console Modification Service Manual

download
Technical Service Bulletin Overhead Console Modification 1997-06 Explorer Sport 2-dr, 2001-06 SportTrac, 1996-01 Explorer 4-dr: Most moonroof and popup sunroof applications require no console modification. Spoiler sunroofs without flush motors require shortening the console. Simply cut the console at the last flip down pocket for a clean vertical wall (no cap required). The entire console is then easily covered in new cloth. Optional – make a cover plate and wrap just the plate in matching headliner cloth. Most full size sunroofs fit the flat spots between the ribs.

2006 Ford Explorer Scheduled Maintenance Guide

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

2002 Ford Explorer Sport/ Sport Trac Cylinder Head Removal and installation manual

download
Removal Both cylinder heads 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information , refer to Section 100-02 . 2. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Drain the cooling system. For additional information, refer to Section 303-03 . 4. Remove the intake manifold. For additional information, refer to Intake Manifold in this section. 5. Remove the cooling fan shroud. For additional information, refer to Section 303-03 . 6. Remove the accessory drive belt. For additional information, refer to Section 303-05 7. Remove the LH valve cover. For additional information, refer to Valve Cover — LH in this section. 8. Remove the RH valve cover. For additional information, refer to Valve Cover — RH in this section. 9. Disconnect the generator electrical connections. 10. Remove the accessory drive belt tensioner. 11. Remove the bolts and the generator and generator mounting bracket as an assembly. 12. Disconnect the crankshaft position (CKP) sensor electrical connector. 13. Disconnect the wiring harness retainers. 14. Disconnect the water temperature indicator sender unit and the engine coolant temperature (ECT) sensor electrical connectors. 15. Disconnect the exhaust gas recirculation (EGR) tube fitting. 16. Remove the upper heater coolant hose. 1. Squeeze the heater hose clamp. 2. Remove the heater coolant hose. 17. Remove the lower heater coolant hose and position aside. 1. Remove the bolt. 2. Squeeze the hose clamp. 3. Remove the heater coolant hose and position aside. 18. NOTE: The coolant hose will be removed with the thermostat housing. Move the coolant bypass hose clamp off the water pump outlet. 19. Remove the bolts, the thermostat housing and the bypass hose. 20. Remove the bolt and detach the wiring harness retainer. 21. Remove the bolts and position the accessory drive bracket aside.22. Detach the wiring harness retainer. 23. Remove the bolt and the oil level indicator tube. 24. Using the special tool, disconnect the LH spark plug wires from the spark plugs. 25. Disconnect the fuel pulse damper vacuum connector. 26. Remove the four bolts and position the fuel supply tube aside. 27. Remove the bolts and the fuel rail and injectors as an assembly.28. NOTE: Mark each of the roller followers to make sure it is installed in its original position during reassembly. Use the special tool to remove the roller followers. 29. Remove the lower radiator hose. 30. Remove the nut and position the A/C tube bracket aside. 31. Using the special tool, set the No. 1 piston at top dead center (TDC). RH cylinder head 32. Remove the RH fenderwell splash shield. 33. Remove the RH camshaft chain tensioner.