Skip to content

p0430 kia sedona

You search PDF repair manual about p0430 kia sedona, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Kia Sorento EX TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle