pass lock reset chevy truck 1998

You search PDF repair manual about pass lock reset chevy truck 1998, if there are search results will appear below. If search results do not exist, please search by others keyword.



  pass lock reset chevy truck 1998 Direct Download speed 5432 Kb/s

  pass lock reset chevy truck 1998 Full Version speed 8172 Kb/s



TOYOTA TACOMA DC XSB RETRACTABLE HARD TRUCK BED COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
STEP 1: POSITIONING CANISTER Remove the top cover from the canister box and set it aside for later installation. Perform a quick inventory to insure all parts are there. Be sure to check inside the small cardboard box for parts. Remove the Canister from the box and set it in the truck bed against the cab. The canister should be resting on the canister end plates and be centered in the truck bed. DO NOT USE A KNIFE TO OPEN THE RAIL BOX. OPEN THE RAIL BOX ALONG THE LENGTH OF THE BOX AND LIFT RAILS OUT TO AVOID SCRATCHING THE SURFACE OF THE RAILS ON THE PACKAGE STAPLES. CAUTION! Canister End Plates INSTALLATION INSTRUCTIONS Slide the four (4) Inner Rail Clamps (2 on each side) through the Tie Down Bars of the truck. (Figure 2B) Place the Outer Angled Rail Clamps on the Inner Rail Clamps (MAKE SURE THE NARROWER EDGE IS DOWN ON THE OUTER ANGLED RAIL CLAMPS) loosely fasten the clamps in place with the 1/4″ Washer, 1/4″ Lock Washer and Rail Clamp Nut on both sides of the truck bed. The fi rst clamp should be placed about 6 inches from the canister (closest to truck cab). The second clamp assembly should be about 4 inches from the end of the Tie Down Bar (closest to the tailgate). Open the rail box along the length of the box, lift rails out to avoid scratching the rail surface on the package staples. The side rails are marked “left” and “right” (left is the driver’s side of the truck). Then Slide Rail Clamp Bracket A on each Rail followed by Rail Clamp Bracket B. Rail Clamp Bracket A should be closest to the Cab of the truck. At this time you will need to install the taligate end of the pull strap to the underside of the drivers side rail using the #8-32 x 3/4 machine screw that is already located at the tailgate end on the underside of the rail. (Figure 2A) Now, with the tailgate closed, place the side rails in position on the truck bed with the Rail Clamp Brackets A & B resting on the Outer Angled Rail Clamps. Loosely assemble the Rail Clamp Brackets to the Outer Angled Rail Clamps with the 1/4″ Washer, 1/4″ Lock Washer and 1/4-20 x 1/2″ Bolt on each side of the truck bed. Center the Rails in the Truck bed. Check spacing in the truck bed between the Left and Right Rails. Spacing should be 51 3/4″. Once correct spacing is achieved tighten the Rail Clamp Brackets A & B only in place Correct spacing to the tailgate should be 1/16″ to prevent the tailgate from striking the side rails when closing. Tighten the Set Screws on both Rail Clamp Bracket A to hold rails in position. ( Adjust spacing from the tailgate by moving rails forward or backward as needed prior to fi nal tightening of set screws .) Apply downward pressure while tightening the Outer Angled Rail Clamp to the Inner Rail Clamp, especially on the tailgate end. This will ensure a tight seal, fi rm seat, and good fi t on the truck bed

Related Content:

Tail Gate mounting Instructions on A25 Volvo Truck, 1954 f100 owners manual, hino truck repair manual, how to install cross rails on buick enclave, instructions on how to install roof rack cross rails on a 2014 Buick Enclave, isuzu npr dashboard guide, Isuzu NPR PRNDL inoperative, kia sedona frame structure, manual 1993 s10 truck, repair Evap soleniod for 2006 chevy 1500

2003 Honda Accord EX A/ T INTERLOCK SYSTEM REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 21-01-2012

download
A/T Interlock System Circuit Diagram SHIFT LOCK SYSTEM CIRCUIT TROUBLESHOOTING 1. Press the brake pedal. Are the brake lights ON? YES -Go to step 2. NO -Repair faulty brake light circuit. 2. Connect the HDS to the DLC. Check engine speed and throttle position in the A/T data list. Is the engine speed at idle, and TPS about 0.5 V? YES -Go to step 3. NO -Repair engine speed or throttle position input. 3. Select SHIFT LOCK SOL TEST in MISC. TEST MENU, then carry out shift lock solenoid function test. Does the shift lock solenoid work properly? YES -System circuit is OK. Check the shift lock mechanism, if necessary. NO -Go to step 4. 4. Remove the center console (See CENTER CONSOLE REMOVAL/INSTALLATION ). 5. Disconnect the shift lock solenoid connector. 6. Turn the ignition switch ON (II). 7. Measure the voltage between No. 1 terminal of the shift lock solenoid connector and body ground. Fig. 3: Measuring Voltage Between No. 1 Terminal Of Shift Lock Solenoid Connector & Body Ground Is there battery voltage? YES -Go to step 8. NO -Check for blown No. 21 fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the shift lock solenoid connector and the under-dash fuse/relay box. 8. Shift the shift lever into the P position, and press the brake pedal. Do not press the accelerator. 9. Measure the voltage between shift lock solenoid connector terminals while pressing the brake pedal Fig. 4: Measuring Voltage Between Shift Lock Solenoid Connector Terminals Is there battery voltage? YES -Check the shift lock mechanism. If the mechanism is OK, replace the shift lock solenoid (see Shift Lock Solenoid Replacement ). NO -Check for poor or loose PCM connector terminal E2 at the PCM, and check for an open in the wire between PCM connector terminal E2 and shift lock solenoid connector. If the connection and wire is OK, substitute a known-good PCM and recheck. KEY INTERLOCK SYSTEM CIRCUIT TROUBLESHOOTING

Related Content:

honda 2005 solenoid c, cavalier selenoide tcc, 2002 mdx shift interlock broken, relay trasmission control on cavalier 2003, how to install transmission shift solenoid buick regal ls 2000, 1998 F-150 Electronic Pressure Control Solenoid Short Circuit, expedition shift solenoid b, lincoln continental p0743, transmisson speed sencer on 2000 f150 how do you change it, 2003 hummer H2 transmission shift connection

2005 and up Toyota Tacoma Cabinet Lock PL5220 Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 06-04-2012

download
Unscrew the Knob and the Cam 2. Insert the Lock from the front and the LockWasher from the rear and the Lock Clip from the side 3. Push the Lock Clip in fully to hold the Lock and Washer in place. 4. Mount the Lock Cam to the Lock. Turn the key to check the Cam turns freely. You may have to pull the Clip slightly for clearance. 5. Drill four holes through the Cover using the stiffening plate as a template. IMPORTANT: Don’t drill through the center bosses. Contents: Lock Cylinder, Lock Washer Lock Screw, Lock Cam, Lock Clip Stiffening Plate, 4 Carriage Bolt, 4 Nuts, Instructions, Warranty Card Tools Required: Screw Driver, Power Drill with 5 MM drill bit, 11MM Socket Tech Support: 1-800-342-5911 6. Insert the 4 Carriage Bolts from the front and mount the Stiffening Plate with the four nuts. 7. Tighten the four Nuts and turn the key to check for smooth operation

2005 -2008 Toyota Tacoma Tailgate Lock PL5200 Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Lock Assembly 2 Washers, 2 Nuts 2 Rod Extenders Instructions Warranty Card Tools Required: Screw Driver T-30 Torx 7 mm Socket Tech Support: Call 1-800-342-5911 Installation Instructions Tailgate Lock PL5200 Toyota Tacoma 2005 -2008 4. Turn tailgate over and put segmented washer over one of the studs 5. Screw the nut onto the stud. Repeat steps 4 and 5 on the other stud and tighten both nuts. 6. Rotate plastic rod retainer using a screw driver and remove rod. 7. 1. Insert rod into Extender slot 2. Twist Extender to retain the rod. 8. 1. Insert Extender onto arm. 2. Twist rod retainer over the Extender. 9. Repeat steps 6, 7 and 8 on the second rod to finish the installation. NOTE: If the tailgate will not open when unlocked, remove the rod extenders LIMITED WARRANTY TERMS AND CONDITIONS 1. INSTALLATION: Pop & Lock TM is not responsible for installing the Pop & Lock TM or for the harm suffered by any person as a result of installing it. 2. WARRANTIES: a) Customer acknowledges that it is unreasonable to believe that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so-called anti-theft or security device is that it will deter many theives. b) POP & LOCK TM MAKES, AND THE CUSTOMER RECEIVES, NO WARRANTY, EXPRESSED OR IMPLIED, EXCEPT THE WARRANTIES OF TITLE TO THE POP & LOCK TM AND THEIR MERCHANTABILITY, PARTICULARLY NO WARRANTY OF FITNESS FOR A PARTICULAR USE OR PURPOSE OR AGAINST INFRINGEMENT. c) As Customer’s only remedy, Pop & Lock TM will repair or replace, at its option and without charge, any lock that is defective in material or workmanship when received by the Customer and is returned to Pop & Lock TM , FOB Pop & Lock’s offices, within one (1) year after its receipt by the Customer. Pop & Lock TM will ship all replacement, or repaired locks to the Customer, FOB Pop & Lock’s shipping point.

Related Content:

diy tailgate lock, 2008 toyota tacoma pdf manual, 2011 toyota tundra camera within tailgate without key hole, diy tacoma power tailgate lock, free toyota tacoma repair manual RM576U2, grease points 2005 -2013 tacoma lube points, How do I install a locking tailgate handle on Tacoma Truck, how to replacere glove box lock 2008 grand prix

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, how to remove the heater core on 2000 VW Beetle, 2010 ford escape dash panel removal, 2004 Buick lesabre inrument cluster removeal, 2003 mitsubishi eclipse replace evapulator, 2002 silverado remove front driveshaft, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette, 2002 ford taurus evap emission line location

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

1988 Cadillac DeVille Steering Column Service and Repair Manual

0

Filed Under (Cadillac Manuals) by admin on 30-01-2012

download
Disassembly 1. Remove dash panel bracket and store bracket in a safe place to prevent damage to mounting capsules. 2. Place column in a vise using both weld nuts of either set A or B, Fig. 29. The vise jaws must clamp onto the sides of weld nuts indicated by arrows shown on set B. Do not place column in vise by clamping onto only one weld nut, by clamping on one weld nut of both sets A and B or by clamping onto the sides not indicated by arrows, as damage to column could result. 3. Inspect steering shaft to determine type of thread used for steering shaft nut. Metric type shafts can be identified by a groove located in area of steering wheel locating splines, while shafts with American type threads do not have this groove. If shaft has metric type threads, the forcing screw of Lock Plate Compressor Tool J-23653 must be removed and replaced with the metric forcing screw J-23653-4 before installing lock plate compressor tool on steering shaft. Compress lock plate using lock plate compressor tool, then pry snap ring from shaft groove and discard wing. Remove lock plate compressor tool and lock plate. 4. Remove directional signal switch, lock cylinder and ignition key warning switch, then remove steering shaft from lower end of column. 5. On power steering columns, remove steering shaft lower bearing from plastic adapter at lower end of column. 6. Remove four turn signal housing to column jacket retaining screws and remove housing and shroud assembly. 7. Remove three shroud to signal housing retaining screws and remove shroud. 8. Using hand as shield to prevent lock inhibitor lever spring wire from flying out, remove lock inhibitor lever and spring wire. 9. Lift ignition switch actuating rod, rack assembly, shaft lock bolt and spring assembly from housing, then if necessary, remove rack preload spring. 10. Remove ignition switch actuator sector through lock cylinder hole by pushing firmly on block tooth of sector with a blunt punch or screwdriver.

Related Content:

ignition switch rack spring, cadillac 2004 deville front panel below steering wheel, cadillac 2004 deville front steering wheel panel

2007 & NEWER TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 01-04-2012

download
The mounting procedure outlined below covers the 2007 and Newer Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the frame and the rear cross member. Remove the skid plate. Do not discard the skid plate or bolts so that they can be reinstalled if the undercarriage is removed. 2. Remove the two bolts from both tow hooks. Remove both tow hooks. Retain the bolts as they will be reinstalled further into the installation procedure. Do not discard the tow hooks so that they can be reinstalled if the undercarriage is removed. 3. Remove the three bumper mount nuts located on the front end of the driver side frame rail. Retain the nuts as they will be reinstalled further into the installation procedure. 4. Place Driver Side Push Beam Support Plate (62B) against the bottom of the driver side truck tow hook mount and against the outside of the driver side frame rail. The front tab of Push Beam Support Plate (62B) must clear the bumper mount studs on the front end of the truck frame. 5. Slide Driver Side Push Beam Support Plate (62B) backward until the three bumper mount studs on the end of the truck frame fully engage the three holes located on Driver Side Push Beam Support Plate (62B). 6. Reinstall the three bumper mount nuts that were removed in step 3. Fasteners should only be finger tight. 7. Assemble Driver Side Push Beam Support Plate (62B) to the tow hook mount using the two bolts removed in step 2. Fasteners should only be finger tight. 3 8. Using Bolt Puller (102) insert one ½” X 1-½” Hex Head Bolt (A) through the hole located on the outside of the driver side frame rail and through the hole located in Driver Side Push Beam Support Plate (62B). Secure with one ½” Split Lock Washer (D) and one ½” Hex Head Full Nut (C). Fasteners should only be finger tight. 9. Tighten the truck tow hook bolts. The heads of these bolts will not be accessible once Push Beam (62) is installed. 10. Repeat steps 3-9 for Passenger Side Push Beam Support Plate (62A). 11. Slide three Nut Plates (101) through the truck cross member. Align Nut Plates (101) with the front side of the two large outside holes and large center hole. 12. Place Angle Bracket (75) against the bottom of the truck cross member. Secure with three ½” X 1-½” Hex Head Bolts (A) and three ½” Split Lock Washers (D) and Nut Plates (101) previously installed inside the truck cross member. Fasteners should only be finger tight. 13. Install Push Beam (62) between Passenger Side and Driver Side Push Beam Support Plates (62A & 62B) using eight ½” X 1-½” Hex Head Bolts (A) and eight ½” Nylon Lock Nuts (B). Push Beam (62) should be mounted at a height of 14-½” from the ground to the center of the hook hole. Fasteners should only be finger tight. 14. Assemble Angle Bracket (75) to Push Beam (62) using four ½” X 1-½” Hex Head Bolts (A) and four ½” Nylon Lock Nuts (B). Fasteners should only be finger tight. 15. Tighten all fasteners, starting with Angle Bracket (75) and continuing forward. 16. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

Related Content:

2007 sorento center bearing, how to install a pushnut

FORD 4-PANEL With New Automatic Latch System Truck WITH Factory Tailgate Lock CLASS 3 Installation Manual

0

Filed Under (Toyota Manuals) by admin on 10-04-2012

download
1) Clean rail surfaces really well with denatured alcohol and make sure they are dry. 2) Press Gasket down firmly the entire length of the gasket 1) Use thin foam double stick tape to hold the clamped hardware in place on inside side rails. The reason we suggest you use this foam is that it is just an extra added protection to keep your clamped hardware from shifting on the sometimes slick surface of some sprayed-in bedliners. • ALL HARDWARE PROVIDED: Stainless steel nuts (18) Part # 9723 or 9723-A – Low Profile Cast aluminum “C” Clamps (16 of them) The only difference with 9723 and 9723-A is that A is a little deeper “C” clamp which is required on some trucks because of the way the inside rail is made. These cast aluminum “C” clamps uninstalled are about the size of a 1 dollar coin and about ¾ inch thick. Part # 9724-T : Latch Installation Tape – (4 pcs.) Part # 9724 – Latch Catch Bracket (4) – These are angled pieces of metal that give your cover’s latches something to “latch to” and are installed with “C” clamps. Part # 9731 – Center Latch Catches (2) Part # 9736 – D Shaped Seals (2) – Described Above Part # 9714 or 9758 – Stainless Steel Screws (18) (Depending on “C” clamps required above) Part # ST-114 – Keyhole Bracket (2) (Mounted at the Hinge closest to the cab of the truck on the inside of the side rail of the truck at that hinge point). Part # 9727 – Box Seal (2) – Described above INSTALLATION OVERVIEW: 1) Measure and make your marks for your masking tape to put your gaskets on each side. 2) Put down masking tape the entire length of the truck 3) Follow masking tape and install peel and stick gaskets (don’t trim in the rear just yet). 4) Place cover onto truck (you will use the measurements provided to make sure the cover is located exactly in the right position 5) Install Keyhole Bracket (holds the 3rd Leg Hinge) Explanation of 3rd Leg Hinge : • 3rd Leg hinge is a flap of metal that is integrated into the hinge • This flap is on the first hinge right behind the cab of the truck • When you mount the cover, this flap hangs straight down, and slides right into the keyhole bracket 6) Install two “C” Clamps to each Keyhole bracket to secure to the truck 7) Install your stainless steel bolt with lock nut that secures the 3rd Leg Hinge (the flap) into the keyhole bracket on each side. That is “your” permanent point of attachment. (THESE ARE THE SAME TWO BOLTS THAT YOU REMOVE TO TAKE OFF THE COVER) *Remember, the cover is now “installed” and cannot slide around – so you MOUNT ALL THE HARDWARE TO FIT THE COVER from here on out 8) Attach center latch catch on inside of side rails using “C” Clamps. *Center Latch Catch: holds center hinge and the 2 panels in the middle down when the cover is closed. When you close the last panel flat onto the tailgate, a stainless steel “button” along each side of the cover is depressed between the 2 panels at the hinge. When this button is squeezed, it actually pushes a stainless steel latch towards the front of the truck catching the center latch on each side rail. 9) Attach Rear Latch Catch Brackets* using “C” Clamps * These are angled pieces of metal that give your cover’s latches something to “latch to” and are installed with “C” clamps. 10) Install Front Latch Catch Brackets using “C” clamps 11) THIS STEP IS ONLY FOR THE Ford F250/F350 SuperDuty Installations ONLY: The outer seal that comes with your cover and is attached on this rail is called a “Side Box Seal” Because the plastic Ford rails on the SuperDuty are ridged/grooved a little deeper and wider than those on the other Ford trucks, a set of small matte black screws are used in addition to the adhesive on the seal to ensure a snug fit. These screws only slightly penetrate the plastic side rail cover and do not come in contact with the underlying metal side rail

Related Content:

2001 toyota tundra tailgate piano hinge installation, liftgate latch stuck how to change spark plugs on ford expedition, remove outer handle 2014 ford fusion, stuck hood latch 2002 ford f150

1994 Ford Pickup F150 WHEEL BEARING ADJUSTMENT

0

Filed Under (Ford Manuals) by admin on 09-02-2012

download
Bronco & F150 (Automatic Locking Hub) 1. Raise and support front of vehicle. Remove wheels. Remove locking hub assembly. See AUTOMATIC LOCKING HUBS under REMOVAL & INSTALLATION. Remove outer lock nut with Spanner Lock Nut Wrench (D85T-1197-A). See Fig. 3 . 2. Remove lock washer. Tighten inner lock nut to 50 ft. lbs. (68 N.m). Back off inner lock nut and retighten to 30-40 ft. lbs. (41-54 N.m). While rotating hub, back off lock nut 90 degrees. Install lock washer so key is positioned in spindle groove. 3. Rotate inner lock nut so pin is aligned in nearest lock washer hole. Install and tighten outer lock nut to 160-205 ft. lbs. (217-278 N.m). Final end play of hub should be .00-.004″ (.00-.11 mm). Torque required to rotate hub and rotor should not exceed 20 INCH lbs. (2.3 N.m). Install hub locks and wheels. 1994 Ford Pickup F150 WHEEL BEARING ADJUSTMENT

Related Content:

WHeel alignment spec 1994 ford f150 4x4, 1994 bronco hub, d85t-1197 a, D85T-1197-A

Related Content:

Tail Gate mounting Instructions on A25 Volvo Truck, 1954 f100 owners manual, hino truck repair manual, how to install cross rails on buick enclave, instructions on how to install roof rack cross rails on a 2014 Buick Enclave, isuzu npr dashboard guide, Isuzu NPR PRNDL inoperative, kia sedona frame structure, manual 1993 s10 truck, repair Evap soleniod for 2006 chevy 1500