Skip to content

pcv valve for 2006 silverado 4 8l v8 engine

You search PDF repair manual about pcv valve for 2006 silverado 4 8l v8 engine, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

2006 Ford Explorer Scheduled Maintenance Guide

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

1994 Toyota Paseo ENGINE IDENTIFICATION/ VALVE CLEARANCE ADJUSTMENT

download
1) Disconnect PCV hose, necessary electrical connections and spark plug wires to access valve cover. Remove nuts, seal washers, valve cover and gasket. 2) Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. Ensure timing mark on crankshaft pulley aligns with “0″ mark on timing belt cover. 3) Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution (360 degrees). 4) Using feeler gauge, measure valve clearance between valve lifter and camshaft on intake valves of cylinders No. 1 and 2, and exhaust valves of cylinders No. 1 and 3. Record valve clearance. Rotate crankshaft clockwise one complete revolution (360 degrees). 5) Measure and record valve clearance on intake valves of cylinders No. 3 and 4, and exhaust valves of cylinders No. 2 and 4. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. VALVE CLEARANCE SPECIFICATIONS TABLE (1) Application In. (mm) Exhaust Valve ………….. .012-.016 (.31-.41) Intake Valve …………… .006-.010 (.15-.25) (1) – Adjust valve clearance with engine cold. 6) If valve clearance requires adjustment, rotate camshaft so lobe on valve to be adjusted is facing upward, away from valve lifter. Position notch area on valve lifter toward inside of cylinder head. DO NOT align notch area with camshaft. Use Valve Clearance Adjuster (SST 09248-55040) to adjust valve clearance. 7) Using SST “A” of valve clearance adjuster, push downward on valve lifter. Place SST “B” between camshaft and valve lifter. See Fig. 2. Ensure enough clearance exists for adjusting shim removal. Remove SST “A”. Fig. 2: Adjusting Valve Clearance Courtesy of Toyota Motor Sales, U.S.A., Inc. 8) Using small screwdriver and magnet, remove adjusting shim. Measure and record thickness of removed shim. Using measured clearance and adjusting shim thickness, select proper replacement adjusting shim. See Figs. 4 and 5. 9) Install replacement adjusting shim. Recheck valve clearance. Apply sealant at indicated valve cover sealing areas on cylinder head. See Fig. 3. 10) Using NEW gasket, install valve cover and sealing washers. Install and tighten nuts to specification. See TORQUE SPECIFICATIONS. To install remaining components, reverse removal procedure. NEW SHIM THICKNESS TAB