ped pinout wiring saturn wiper motor

You search PDF repair manual about ped pinout wiring saturn wiper motor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ped pinout wiring saturn wiper motor Direct Download speed 5432 Kb/s

  ped pinout wiring saturn wiper motor Full Version speed 8172 Kb/s



Windshield Wiper Linkage Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
Installation Instructions 1. Place the Wiper Motor Mount Plate (FFR# 25391) along the edge of the ¾” shock tower support tube on the passenger side and the top of the footbox front wall aluminum. Mark the location for the riv nuts (4 total). 2. Drill the riv nut holes using a 25/64″ drill bit. You may want to begin by using a smaller drill bit to drill a pilot hole first (shown). 3 3. Intsall the 1/4″ riv nuts (4) using the supplied riv nut tool. 4. Install one of the rod ends (FFR# 25724) with the supplied jam nut (FFR# 25725) onto the wiper motor arm (1/2″, 9/16″ wrenches). You will have to trim some of the excess thread off of the rod end in order for it to have sufficient clearance between it and the wiper motor mount plate. 4 5. Place the wiper motor in the mount plate (FFR# 25391) so the pins on the motor fit inside the holes in the mount plate and the three threaded holes in the motor line up with the corresponding holes in the mount plate. 6. Using the three Corvette screws that held the motor in place, fasten the motor to the mount plate (T- 30 Torx). 7. Place a nylon spacer (FFR# 10960) between the frame and the mount plate at each of the riv nuts and bolt the plate into positon using the supplied ¼”-20 x 1.5″ long bolts (4mm allen).
6 ATTENTION: For the bolt at the front corner of the plate, you may have to use the supplied washers as well as the nylon spacer to prevent the bolt from bottoming out before the plate is firmly in place (See photo). 8. Screw the supplied section of threaded rod (FFR# 25723) into the rod end on the wiper motor. 7 9. Slide the aluminum tube (FFR# 25934) over the threaded rod and measure how much of the aluminum tube will need to be trimmed once the rod end is screwed on. Trim the tubing with a tubing cutter/hacksaw/cutoff wheel. 10. As you did with the rod end on the wiper motor, you will have to trim the threads on the rod end to clear the aluminum. 11. Place the aluminum tube over the threaded rod, then screw the rod end (FFR# 25724) onto the rod until tight. 12. Before installing the wheel box to the body you will have to trial fit the wiper arm to the wheel box. It is a tight fit, so you may have to spray the splines with some WD-40 or some oil and tap the wiper arm onto the splines. Remove the wiper arm from the wheelbox so you can bolt it to the body. 8 13. Follow the instructions in the assembly manual for bolting the wheelbox to the body. 14. Install the rod end on the wiper wheel box arm with the supplied jam nut (FFR# 25725) (1/2″, 9/16″ wrenches). 15. Install the wiper blade (FFR# 25629) onto the wiper arm (FFR# 25552). 16. Clip the wiper arm onto the shaft of the wiper wheel box, making sure that the tab on the arm clips into the channel on the wheel box shaft (clip shown). 9 17. Spray the windshield with water, or glass cleaner. Check the sweep by turning the wipers on – start with the slowest setting to avoid damaging the linkage or running the wiper beyond the windshield. Make any necessary adjustments, and the linkage installation is complete

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage

Toyota Landcruiser / Scout Weatherproof Harness Wire Harness Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-03-2012

download
Grounding the Automobile A perfectly and beautifully wired automobile will nevertheless have bugs and problems if everything is not properly grounded. Do not go to the careful effort of installing a quality wire harness only to neglect proper grounding. Note: The Painless Wire Harness Kit includes no ground wire except the black wire from the two headlamp connectors. You must supply ground wire (14-16 gauge) for all circuits. 6.3.1 Connect a Ground Strap or Cable (2-gauge minimum) from the Negative Battery terminal to the automobile chassis (frame). 6.3.2 Connect a Ground Strap from the Engine to the chassis (even a 10-gauge wire is too small) . DO NOT RELY UPON THE MOTOR MOUNTS TO MAKE THIS CONNECTION . 6.3.3 Connect a Ground Strap from the Engine to the Body. 6.3.4 If you have a fiberglass body you should install a terminal block to ground all your Gauges and Accessories. Ground the Terminal Block with at least a 12-gauge wire to the chassis. 6.4 Terminal Installation and Making Connections Note: In the following steps you will be making the circuit connections. Before you start, you should carefully read Sections 7.0 through 10.0 , as appropriate, and continually refer to Section 10.0 , DOUBLE- CHECKING your routing and length calculations before cutting any wires and making connections. Give special attention to Turn Signal and Ignition Switch connections. These can be somewhat confusing. 6.4.1 Have all needed tools and connectors handy. 6.4.2 Select the correct size terminal for the wire and stud application. 6.4.3 Determine the correct wire length and cut the wire. Remember to allow enough slack in the harness and wires at places where movement could possibly occur, such as automobile body to frame, frame to engine, etc. Double-check your calculations. 6.4.4 Strip insulation away from wire. Strip only enough necessary for the type of terminal lug you are using. Note: In the following step, make sure that the terminal is crimped with the proper die in the crimping tool. An improper crimp will NOT make a good connection. 6.4.5 Crimp the terminal onto the wire. CAUTION: DO NOT OVER-CRIMP! 6.4.6 Connecting the harness throughout the groups is a redundant process. Make sure that each wire is FIRST properly routed and THEN attach. DO NOT ATTACH FIRST THEN ROUTE AFTERWARD. 6.4.7 When all wires are attached, tighten the mounts and ties to secure harness permanently. 6.5 Testing The System 6.5.1 Use a small (10 amp or less) battery charger to power up the vehicle for circuit testing. If there is a problem anywhere, the battery charger’s low amperage and internal circuit breaker will provide circuit protection. CAUTION: IF YOU HAVE NOT YET DISCONNECTED THE BATTERY FROM THE AUTOMOBILE, DO SO NOW! DO NOT CONNECT THE BATTERY CHARGER WITH THE BATTERY CONNECTED. Connect the battery charger’s NEGATIVE output to the automobile chassis or engine block and its POSITIVE output to the automobile’s positive battery terminal. 6.5.2 INDIVIDUALLY turn on each light, ignition, wiper circuit, etc. and check for proper operation. Note: The turn signals will not flash properly if you do not have both the front and rear bulbs installed and connected. 6.5.3 When all circuits check out THEN attach the battery cable to the battery for vehicle operation

Related Content:

where are the battery terrminals on a 2012 pruis, 1996 ford f53 chassis circuit board diagram, 1996 ford F53 wiring diagrams, 97 cadillac deville ground location, FORD E-450 FUEL PUMP WIRING

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

starter motor repair manual, mitsubishi canter (4D35) repair manual pdf, 07 yukon 4wd left side motor mount replace, repairing power window on 2003 ford focus, remove water deflector 2000 silverado window, parts diagram 1990 grand prix 4 door drivers window, instructions on wiring a 350 motor, How to test end coder, gm stepper motor replacement, replacement of acadia thermostat

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, 86 corvette wiring schematics, location of vent valve solenoid on 2010 ford ranger, damaged fuel pump wiring, proper connection for horn relay 1968 chevelle, fan cable for 1998 dodge caravan, 1998 s10 6 cylindes fuel regulator diagram, pontiac grand am fuel pump wireing harness replacement instructions

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

Toyota Sequoia SR5 2001-2006, Toyota Tundra 2000-2006, Toyota Tundra D-Cab 2005-2006 Signal Mirror Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
1. Open the driver side door and lower the window. 2. Remove the door panel, kick panel, and plastic trim piece along the bottom of the door frame. 3. Disconnect the mirror wire harness. Remove the three mirror mounting nuts and remove the mirror housing from the vehicle. 1 2 3 Mirror Replacement – 2 – 4 There is a plug seated in a socket in the center of the mirror that holds the mirror in the mirror housing. Lift up the inboard edge of the mirror. Use a small pry bar and pry up around the center of the mirror until the plug unseats from the socket. 5 There are two drive pins on the bottom and outboard sides of the mirror. Hold the top of the mirror away from the mirror housing and pry away the bottom drive pin from the back of the mirror. 6 Hold the inboard side of the mirror away from the mirror housing and pry away the outboard drive pin from the back of the mirror. IF heated, disconnect OE heater wire from heater terminals. Note: During the removal of the original mirror, if motor pins stay attached to the back plate, use “V” end in small pry bar or needle nose pliers to disengage pins from back plate. Set the mirror aside. 7 8 Using the shorter of the two harnesses from the kit, tape the end without the mating connector to the end of the gopher wire. Remove the foam insulation from the mirror housing sail. Starting from the inside of the mirror housing, guide a piece of gopher wire down alongside the existing factory wire harness and out of the bottom of the mirror housing sail. 9 Pull the gopher wire and wire harness through the mirror housing until about 4 inches of wire remain inside the mirror housing.
13 Tuck the wire harness behind the Signal® mirror. Insert the other drive pin into the outboard pin socket (socket closest to the optic module). Align the socket in the center of the Signal® mirror over the plug on the center of the mirror mount. Align drive pins to its mating slots on the motor mount and vice-versa. Anti-vibration tab should be tucked inside housing. 14 Use the palm of your hand and firmly press down on lower portion (marked boundaries) of the Signal® mirror until it snaps into position. Press down carefully on the mirror outboard edge to engage outboard drive pin into mirror mount socket. 15 Press mirror down carefully on the lower edge to engage the lower drive pin into motor mount. Remount mirror to door, then use Electronic Hand Control to relocate mirror position. Gently clean any finger mark/dirt away from mirror using paper towel and glass cleaner. 10 Guide the Signal® mirror harness along the existing path of the factory wire harness and through the foam insulation. Remove any slack in the wire. Reposition the foam insulation on the mirror housing sail. 11 Connect the Signal® mirror mating connector to the Signal ® mirror harness. If heated , reconnect the heater wires to the heater terminals on the back of the new Signal® mirror. NOTE: There is no polarity so the wires may be interchanged. Disregard heater connections on vehicles not equipped with outside heated mirrors. 12 The drive pins must be aligned before installing the Signal® mirror. If needed, insert a drive pin into the lower socket on the mirror mount. Align the nubs on the lower drive pin so it points to the round plug in the center of the mirror mount.

Related Content:

how to access to wiring harness for radio on 2006 Buick Lucerne, 2006 malibu door wiring diagram, Saturn ION-2 2 2 L4 GAS Wiring Diagram, Repairing a ford F-150 side mirror 2011, repair link pins on Tundra 2000, OnStar FMV Wiring Instructions, mirror glass removal f150, how to replace heated power mirror glass 2004 ford f150, how to remove a side mirror from a 1994 ford f150 truck, 2000 mercury cougar drivers side mirror free replacement instructions

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

1992 Cadillac Deville 4.9L Windshield Wiper Blade and Arm REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Cadillac Manuals) by admin on 22-05-2011

download
REMOVAL & INSTALLATION Catera Open the hood. 1. Remove the windshield wiper arm stud cap that conceals the nut. 2. Remove the windshield wiper arm nut. 3. Grasp the windshield wiper arm with both hands. 4. Use a rocking motion to loosen the windshield wiper arm from the pivots. 5. Remove the windshield wiper arm and blade. 6. To install: Installation is the reversal of the removal procedure. 7. Deville and Fleetwood WIPER ARM Raise the hood as needed for access to the wiper arms. 1. Operate the wipers and turn the ignition OFF when the wipers are at the mid-wipe position. 2. Lift the wiper arm from the windshield. 3. On 1990 vehicles, pull the retaining latch and remove the arm from the transmission shaft. 4. On 1991-93 vehicles, disengage the retaining latch using a suitable tool and remove the arm from the transmission shaft. 5. To install: Install the wiper arm onto the transmission shaft. 6. Push the retaining latch in and return the arm assembly to the windshield. 7. Park the wipers. If adjustment is necessary, proceed as follows: Remove the right wiper arm. a. Open the small door to access the wiper linkage; refer to the illustration for details. b.

Related Content:

1992 cadillac seville manual free download, how to remove wiper arm assembly chevy impala recalls, 1992 Cadillac Deville Owners Manual, 2007 chevy tahoe rear windshield wiper arm remove, cad 1992 seville horn low volume ?, how to replace a windshield wiper motor on a 2004 impala, remove wiper arm 04 ompala, video of how to install a windshield wiper arm on a rv

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 27-02-2011

download
Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI 3. Disconnect the wire harness connector to the blower motor control module. 4. Install a capacitor, P/N 25073556, into the blower motor control module connector using the following steps. Refer to the illustration above to locate the positive and negative leads of the capacitor. Refer to the Splicing Copper Wire Using Splice Clips procedure in the Wiring Systems section of SI (Document ID #303646) for more information on using splice clips. 5. If the customer concern was of a blower motor that continues to run after key off, then replace the blower motor control module and install the capacitor . Refer to the blower motor control module Replacement procedure in the HVAC section of SI. This condition is the only time you need to replace the blower motor control module. 6. Reconnect the blower motor control module connector. 7. Install the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement- Right procedure in the Instrument Panel, Gages and Console section of SI. 8. Reconnect the negative cable to the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 9. Verify proper operation of the blower motor.

Related Content:

replace 2002 suburban fan motor, what screws are used to install a lacrosse blower resistor, 2004 cavalier stepper motors, hino blower motor replace procedure, installing heaterfan motor dodge grand caravan 2011, instructions for replacing 2004 pontiac grand prix blower motor, is the resisistor built in the blower motor on a 2012 chevy sonic?, remove heat blower motor 67 grand prix, to replace an a/c motor on a 2003 civic, wireing for blower control 2004 silverado

2004 Chevrolet Aveo SPARK PLUG REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 12-06-2012

download
Courtesy of GENERAL MOTORS CORP. 2. Loosen the 4 bolts and remove the engine cover. Fig. 117: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. 3. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Courtesy of GENERAL MOTORS CORP. 2. Loosen the 4 bolts and remove the engine cover. Fig. 117: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. 3. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Fig. 118: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. NOTE: Be sure plug threads smoothly into cylinder head and is fully seated. Use a thread chaser if necessary to clean threads in cylinder head. Cross- threading or failing to fully seat spark plug can cause overheating of plug, exhaust blow-by, or thread damage. Follow the recommended torque specifications carefully. Over or under-tightening can also cause severe damage to engine or spark plug. 2. Install the spark plugs to the engine. Tighten: Tighten the spark plugs to 25 N.m (18 lb ft). 3. Install the spark plug wires to the spark plugs. Refer to Spark Plug Wire Replacement . Fig. 119: Identifying Cover Screws Courtesy of GENERAL MOTORS CORP. 4. Install the engine cover and tighten the 4 bolts. Tighten: Tighten the engine cover bolts to 3 N.m (31 lb in).

Related Content:

ISX 12 drain plug thred, changing spark plugs on 2008 avalon, 2004 chevy aveo spark plug wire replacement, Ford 500 Spark Plug Change, how to change spark plugs in 2009 Aveo, spark plug calibration, manual shifter not working on 2008 nissan titan, loctite spark plug, is 1999 pontiac grand am obd2, intermitant misfire in morning 2008 torrent

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage