perkins 4 cylinder head bolt torque

You search PDF repair manual about perkins 4 cylinder head bolt torque, if there are search results will appear below. If search results do not exist, please search by others keyword.



  perkins 4 cylinder head bolt torque Direct Download speed 5432 Kb/s

  perkins 4 cylinder head bolt torque Full Version speed 8172 Kb/s



1999 Ford Escort/ Tracer Cylinder Head Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-04-2012

download
Removal 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. WARNING: Fuel supply lines will remain pressurized for long periods of time after engine shut down. This pressure must be relieved before disconnecting any fuel lines or fuel system components. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Remove the engine air cleaner outlet tube. For additional information, refer to Section 303-03 . 4. Remove the timing belt. For additional information, refer to Timing Drive Components—Timing Belt in this section. 5. Remove the vacuum hoses at the: * positive crankcase ventilation (PCV) valve (6A666). * throttle body (9E926). * intake manifold (9424). * fuel pressure sensor. 6. Disconnect the fuel charging wiring (9D930) electrical connectors at main engine connector. 7. Disconnect the crankshaft position (CKP) sensor electrical connector. 8. Disconnect the fuel line. For additional information, refer to Section 303-04 . 9. Remove the power steering pump (3A674) and bracket as an assembly. For additional information, refer to Section 211-02 . 10. Remove the generator (GEN). For additional information, refer to Section 414-02 . 11. Remove the oil level indicator tube (6754). For additional information, refer to Oil Level Indicator and Tube in this section. 12. Disconnect the heater hoses. For additional information, refer to Section 412-02 . 13. Lower the vehicle. 14. Disconnect the upper radiator hose (8260) from the thermostat housing water hose connection. For additional information, refer to Section 303-03 . 15. Remove the camshafts (6250). For additional information, refer to Camshaft in this section. 16. Remove the ignition coil (12029) and bracket. For additional information, refer to Section 303-07 . 17. Remove the water thermostat housing. For additional information, refer to Section 303-03 . 18. Disconnect the knock sensor electrical connector. 19. Remove the generator bracket-to-cylinder head bolt. 20. Remove the bolts and the cylinder head (6049). 21. Remove the cylinder head gasket and discard. Installation WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and may be ignited, resulting in possible personal injury. 1. CAUTION: Do not use abrasive grinding discs to remove gasket material; use only plastic manual scrapers. Do not scratch or gouge the aluminum sealing surfaces. Clean all gasket material from the mating surfaces on the cylinder head and cylinder block. Clean out the bolt holes in the cylinder block. Inspect the cylinder head for flatness. For additional information, refer to Section 303-00 . 2. Install a new head gasket on the cylinder block. 3. CAUTION: Do not attempt to install the cylinder head assembly without assistance. Installation of the cylinder head assembly requires two people or possible injury may occur. CAUTION: The bolts are torque-to-yield and must be replaced or engine damage may occur. Tighten the bolts in three stages in the sequence shown. * Stage 1: Tighten the bolts to 15-25 Nm (12-18 lb-ft). * Stage 2: Tighten the bolts to 35-45 Nm (26-33 lb-ft). * Stage 3: Tighten the bolts an additional 105 degrees. 4. Install the generator bracket-to-cylinder head bolt. * Tighten to 20 Nm (15 lb-ft). 5. Connect the knock sensor electrical connector. 6. Install the thermostat housing. For additional information, refer to Section 303-03 . 7. Install the ignition coil and bracket. For additional information, refer to Section 303-07 . 8. Install the camshafts. For additional information, refer to Camshaft in this section. 9. Connect the upper radiator hose. For additional information, refer to Section 303-03 . 10. Raise and support the vehicle. For additional information, refer to Section 100-02 . 11. Install the heater hoses. For additional information, refer to Section 412-02 . 12. Install the generator and bracket assembly. For additional information, refer to Section 414-02 . 13. Install the power steering pump and bracket assembly. For additional information, refer to Section 211-02 . 14. Connect the fuel lines. For additional information, refer to Section 310-00 . 15. Connect the crankshaft sensor electrical connector.

Related Content:

fleetwood sedona manuals, Honda Civic 2003 number #3 Cylinder pattern, Workshop Manual (WSM) Section 303-04, 4 8 head bolt tightening sequence, 2001 mitsubishi 3 0 cylinder torque specs, workshop manual section 303 14, wsm 303-14a, workshop information system saab, where is the knock sensor on a 2006 toyota tundra 4 7 v-8 truck, trailblazer front frame section

2001 Pontiac Sunfire L4-2.2L VIN 4 Cylinder Head Removal And Installation Manual

0

Filed Under (Pontiac Manuals) by admin on 11-06-2012

download
Cylinder Head Replacement * Tools Required * J28467-360 Engine Support Fixture * J36660-A Torque Angle Meter. Removal Procedure 1. Disconnect the negative battery cable. 2. Relieve the fuel system pressure. 3. Drain cooling system . 4. Remove the alternative fuel module assembly. Remove the drive belt . 5. Remove the air cleaner outlet duct and resonator assembly. 6. Support engine using floor jack and block of wood. 7. Remove the engine mount . 3. Remove the intake manifold . 9. Remove the exhaust manifold 10. Disconnect the Engine Coolant Temperature Sensor ( ECT ) electrical connection. 11. Remove the valve rocker arm cover. Important: When removing valve train components keep them in order. Do this to ensure that the components are installed in the same locations and with the same mating surfaces as when removed. 12. Remove the rocker arms and pushrods. 13. Remove the generator. 14. Remove the generator rear brace. 15. Remove the power steering pump. Position the pump aside with the lines attached. 16. Remove the radiator inlet pipe. 17. Remove the ignition coil assembly. 18. Remove the accessory bracket. 19. Disconnect the secondary ignition wires from the spark plugs . 20. Remove the cylinder head bolts. 21. Remove the cylinder head. 22. Clean the following components: * Head gasket surface * Valve rocker arm cover gasket surface * Threads Installation Procedure Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin

Related Content:

01 sunfire head gasket, 2004 kia sorento head gasket, rig master cobrahead pdf, kancil cylinder head torque, 02 Buick rendezvous head gasket install you tube, kancil head bolt torque, rig master cobrahead manual, pt cruiser head gasket replacement, Prado engine overhaul piston replacement, pontiac g5 ac drain line

1996 Nissan Altima GLE TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Nissan Manuals) by admin on 24-02-2011

download
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables. 2. Remove front exhaust tube. Remove intake manifold collector supports, and intake manifold. Remove exhaust manifold with catalytic converter. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. Remove injectors and fuel rail as an assembly. Remove distributor cap and spark plugs. 3. Set cylinder No. 1 at TDC of compression stroke, ensuring marks on crankshaft pulley and front cover align, and distributor rotor points to spark plug wire No. 1 on cap. Remove cylinder head cover. Remove distributor. 4. Prevent camshafts from turning, and remove camshaft sprocket bolts. Remove camshaft sprocket. See Fig. 13 . Mark and remove camshaft bearing caps in reverse order of installation. See Fig. 16 . Remove camshafts. 5. Loosen cylinder head bolts in 2 or 3 steps, in reverse order of tightening sequence. See Fig. 11 . Remove camshaft sprocket cover. Remove outer (upper) chain tensioner and guide. Remove outer timing chain. Remove idler sprocket bolt. Remove cylinder head. 6. Remove oil pan and oil strainer. See OIL PAN. Remove accessory drive belts. Remove A/C compressor idler pulley (if equipped). Remove crankshaft pulley. Remove front cover. Remove chain tensioner, tensioner arm and chain guides. Remove inner (lower) timing chain and idler sprocket. Remove oil pump drive spacer and crankshaft sprocket. Inspection 1. Inspect chain roller links. Replace chain if roller links are cracked or worn. Inspect cylinder head and cylinder block mating surfaces for warpage. If warpage exceeds specification, machine cylinder head. See CYLINDER HEAD under ENGINE SPECIFICATIONS. 2. If machining reduces cylinder head height to less than specification, replace cylinder head. After machining, rotate camshaft by hand. Replace cylinder head if camshaft does not rotate freely.

Related Content:

1997 altima cam timing, cummins n14 cylinder heads, 03 2az-fe head dowel pins, how to disable child licks on 2013 GMC terrain, how to install cylinder head on c-15cat engine, how to replace cilinder head in1 8 toyota, how to top overhaul peugeot 206, is timing set on compresson stroke 2000 2 0 vw beetle, procedure on removal fo cv axle in 2005 volvo s40 2 4i, removing ih1066 cylinder liners

2001 Toyota Echo Transmission and Drivetrain Removal And Installation Manual

0

Filed Under (Toyota Manuals) by admin on 10-03-2012

download
REMOVAL 1. REMOVE HOOD HINT: At the time of installation, please refer to the following item. Adjust the hood. 2. REMOVE WIPER ARM HINT: At the time of installation, please refer to the following item. Adjust the installation position of the wiper arms 3. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS 4. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 nuts and No. 2 cylinder head cover. Torque: 7.0 Nm (71 kgf-cm, 62 inch lbs.) 5. REMOVE BATTERY AND AIR CLEANER CASE ASSEMBLY WITH AIR HOSE 6. DISCONNECT WIRE HARNESS FROM TRANSAXLE Remove the set bolt of the wire harness clamp. 7. DISCONNECT CONTROL CABLE a. Remove the 2 clips and washers. b. Remove the 2 clips and disconnect the control cables from the transaxle. 8. DISCONNECT CLUTCH RELEASE CYLINDER a. Remove the set bolt of the clutch line. Torque: 4.9 Nm (50 kgf-cm, 43 inch lbs.) b. Remove the 2 set bolts of the clutch release cylinder. Torque: 12 Nm (120 kgf-cm, 9 ft. lbs.) 9. DISCONNECT GROUND CABLE Remove the set bolt of the ground cable from the engine left mounting bracket. 10. DISCONNECT BACK-UP LIGHT SWITCH AND VEHICLE SPEED SENSOR CONNECTORS 11. REMOVE 2 TRANSAXLE UPPER SIDE MOUNTING BOLTS Torque: 33 Nm (340 kgf-cm, 25 ft. lbs.) 12. REMOVE STARTER SET BOLT Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 13. ATTACH ENGINE SLING DEVICE TO ENGINE HANGER Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print a. Remove the bolt. b. Install the 2 No. 1 engine hangers with the bolts in the correct direction. Parts No.: No. 1 engine hanger: 12281-21010 Bolt: 91642-81025 Torque: 40 Nm (400 kgf-cm, 29 ft. lbs.) c. Attach the engine chain hoist to the engine hangers. CAUTION: Do not attempt to hang the engine by hooking the chain to any other part. 14. RAISE VEHICLE CAUTION: Make sure that the vehicle is securely supported. 15. REMOVE LH ENGINE UNDER COVER 16. DRAIN TRANSAXLE OIL Oil grade: API GL-4 or GL-5 Viscosity: SAE 75W-90 Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts) Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 17. REMOVE RH AND LH FRONT DRIVE SHAFTS 18. REMOVE SUSPENSION MEMBER a. Remove the 2 set nuts and bolt of the engine rear mounting insulator from the suspension member. b. Disconnect the sliding yoke. c. Power steering: Disconnect the pressure feed and return tubes. d. Power steering: Disconnect the tube clamp

Related Content:

torque clutch converter solenoid problems 2001 isuzu rodeo, 2004 chevy tahoe 5 3 air conditioner belt tensioner bolt torque specs, 2006 nissan navara d40 cylinder head bolt tightening, 6sa1 flywheel injector settings, flywheel bolt torque 3406b, how to adjust clutch pedal on toyota echo

1995 Ford Truck F 150 2WD Pickup New Cylinder Head Bolt Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-02-2012

download
ORQUE SPECIFICATIONS FOR THE NON-FLANGED STANDARD HEX HEAD BOLTS, TIGHTEN IN TWO (2) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 75-88 N-m (55-65 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 88-98 N-m (65-72 lb.ft.). FOR ALL TORQUE TO YIELD HEX HEAD BOLTS, TIGHTEN IN THREE (3) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 34-47 N-m (25-35 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 61-75 N-m 45-55 lb.ft.). 3. Tighten all bolts in sequence (Figure 2) an additional 1/4 turn (85-95 degrees). NOTE: WHEN THE CYLINDER HEAD BOLTS HAVE BEEN TIGHTENED FOLLOWING THESE PROCEDURES, IT IS NOT NECESSARY TO RETIGHTEN THE BOLTS AFTER EXTENDED OPERATION. CAUTION: TORQUE-TO-YIELD CYLINDER HEAD BOLTS MUST BE REPLACED WITH NEW BOLTS. DO NOT REUSE TORQUE-TO-YIELD BOLTS. TORQUE-TO-YIELD BOLTS MAY ONLY BE USED ONE (1) TIME. PART NUMBER PART NAME F3ZZ-6065-E Cylinder Head Bolt

Related Content:

1999 2 5 ford ranger head bolt torque, D-17 manfold bolt torqe, ranger 1999 3 0 head torque diagram, torque angle specs 3100 1998 buick, torque sequence 300m 3 5 heads

1999 Honda Civic EX TORQUE SPECIFICATIONS

0

Filed Under (Honda Manuals) by admin on 04-02-2012

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Related Content:

pontiac vibe head torque secuensia, 1999 honda civic door bolt torque specifications, tork settings for fd 42 engine, nuts&bolts service, nissan fd42 tuning, j35 honda bolt pattern transmission, how to rebuild a saturn 1 9 sohc, honda generator bolt torque spec, head bolt torque specifications 2000 buick century, fd42 manifold gasket

2004 Toyota Camry Disc Brake System Service/ Repair Manual

0

Filed Under (Toyota Manuals) by admin on 13-04-2012

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram

TOYOTA TO CHEVY AND BUICK ENGINE – TURBO CHARGED INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

download
INSTALLATION INSTRUCTIONS: 1. Install the pilot bushing into the engine crank. 2. Bolt the flywheel to the engine crank using special flywheel bolts. 3. Assemble the clutch assembly and special disc to the flywheel using special clutch bolts. 4. Assemble the clutch release arm to the inside ball pivot of the bellhousing. 5. Bolt the slave cylinder to the outside of the bellhousing. 6. Test fit the bellhousing assembly over the clutch assembly and onto the engine block. 7. Place the N1430 release bearing onto the clutch arm fork. 8. Adjust the length of the slave cylinder push rod to a length that provides a minimum of 1/8″ clearance between the release bearing face and clutch fingers. 9. This test fit over the clutch assembly is primarily done for establishing the push rod length. If this procedure is eliminated, you will not have any visual inspection for verifying the push rod adjustment. 10. Remove the bellhousing assembly from the engine. 11. Bolt the bellhousing to the front of your Toyota 5 speed transmission using the original bolts. Make sure that the two dowel pins installed in the face of the 5 speed transmission are properly fitted to the Advance Adapter bellhousing. 12. Slide the new release bearing onto the Toyota bearing retainer. Make sure that there is grease in the internal cavity of the release bearing. Most new bearings are pre-lubricated. 13. With all the components in position, you can now bolt the new bellhousing assembly onto the engine block. We have provided six (6) new socket head bolts, 3/8″-16 x 1-1/2″ long for this purpose. Make sure the engine dowel pins are properly aligned with the new bellhousing dowel pin holes. DO NOT FORCE THE BELLHOUSING ONTO THE ENGINE BLOCK. Some applications may require the tip of the input shaft to be modified slightly. The bellhousing must fit evenly to the engine block. 14. With the bellhousing now in position and the slave cylinder push rod installed, you should be able to verify the clearance between the release bearing & clutch fingers. The lever should have movement of approximately 1/8″ to 1/4″. CAUTION : If you have too much clearance, you will be utilizing too much of the slave cylinder stroke and could possibly prevent you from obtaining a full clutch release. A light duty return spring attached to the clutch release arm will prevent any premature contact of the release bearing with the clutch fingers. 15. The Toyota Land Cruiser slave cylinder will replace the original Toyota slave cylinder. The Toyota truck hydraulic slave cylinder line will have exactly the same fitting size as used on the Land Cruiser slave cylinder. 16. With the new slave cylinder installed, you can now bleed the slave cylinder installation by pumping up the slave cylinder pedal. Most installations are compatible with the original Toyota master cylinder. We have encountered a few installations that require changing of the Toyota master cylinder to a smaller 3/4″ piston. If you have any type of clutch difficulty related to full disengagement of the clutch assembly, contact Advance Adapters for any updated information.

Related Content:

how to install aslave cylinder on 2007 mustang gt, 2007 mustang gt slave cylinder, slave cylinder rod length rx7 series 1, renault modus clutch bleed procedure, PT Cruiser Clutch Adjustment, mazda rx7 clutch slave cylinder push rod dimensions, looking for push type slave cylinder adapter kit for small block chevy, how to install dowell pins, dowel compressor, chevy rod bearing fitting and installation

2000-2004 Toyota Tundra 4.7L V-8 Two and Four Wheel Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust manifold flanges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to prevent the vehicle from rolling off the jack stands. 2. Spray WD-40 or some type of penetrating oil on all accessible fasteners and fittings before attempting to remove them. 3. From underneath the vehicle disconnect the exhaust system from the exhaust manifolds by unbolting the (3) bolts at the collectors. Then unbolt the driver side catalytic converter from the exhaust assembly and temporarily remove it from the vehicle. PASSENGER SIDE 4. On the passenger side remove the (4) bolts attaching the heat shields to the factory manifold. 5. Next, carefully unplug the O2 sensor from its harness. 6. Now remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 7. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 8. Transfer the O 2 sensor from the factory manifold to the new passenger side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 9. Now you are going to install the new JBA Header, but first there is some preparation of the hardware required. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. DRIVER’S SIDE 10. Just like you did in step (4) remove the (4) bolts attaching the heat shields to the driver side factory mani- fold. 11. Next, carefully unplug the O2 sensor from its harness. Unbolt the dipstick bracket from the head and remove the dipstick tube. 12. Remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 13. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 14. Transfer the O 2 sensor from the factory manifold to the new driver side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 15. As you did on the passenger side, prepare the hardware before installing the driver side header. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. Re-install the dipstick tube. 16. Install the driver side catalytic converter. 17. Connect the exhaust system to the new headers using hardware and gaskets supplied. Reconnect O2 sensors. 18. Check to insure adequate clearance between header and shifter cable (small cable that runs from firewall, to brace on fender well, to transmission) . More clearance can be gained by adjusting (bending) brace on fender well. 19. Recheck everything

Related Content:

2004 honda civic head bolt torque, 4y toyota head torque

2000 Dodge Intrepid Timing Chain Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 21-11-2011

download
REMOVAL 1.Remove upper intake manifold. 2.Remove cylinder head covers, crankshaft damper, and timing chain cover. CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. Fig. 70 3.Align crankshaft sprocket timing mark to mark on oil pump housing (Fig. 70). The mark on oil pump housing is 60° ATDC of #1 cylinder. CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage Fig. 74 4.Remove primary timing chain tensioner from right cylinder head (Fig. 74). 5.Remove camshaft position sensor from left cylinder head (Fig. 69). 6.Remove chain guide access plug from left cylinder head (Fig. 69). NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction. 7.Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper and sprocket (Fig. 69). 8.Remove left side camshaft sprocket attaching bolts and remove sprocket (Fig. 69). 9.Remove lower chain guide and tensioner arm (Fig. 69). 10.Remove the primary timing chain. INSTALLATION 1.Inspect all sprockets and chain guides. Replace if worn. Refer to Crankshaft Gear/Sprocket, for removal and installation procedures. 2.If removed, install right and left side short chain guides (Fig. 69). Tighten attaching bolts to 28 Nm (250 in. lbs.) 3.Align crankshaft sprocket timing mark to the mark on oil pump housing (Fig. 71). NOTE: Lubricate timing chain and guides with engine oil before installation. 4.Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (Fig. 71). 5.Lower the primary chain with left side sprocket through the left cylinder head opening

Related Content:

2006 trailblazer timing marks, diagram of a 00 lincoln ls 3 9 liter timing chain and gears, 2004 pontiac sunfire timing chain replacement, 04 ford escape timing chain settings, tdc on jaguar 4 0, sport trac timing chain replacement interval, number one cylinder cam is not near 11 o\clock why? 04 nissan quest, is crankshaft position sensor removed when replacign timing chain on 2001 durango, installing timing chain on 2000 dodge ram 1500, how to replace the timing chain on a 2004 maxima 3 5

Related Content:

fleetwood sedona manuals, Honda Civic 2003 number #3 Cylinder pattern, Workshop Manual (WSM) Section 303-04, 4 8 head bolt tightening sequence, 2001 mitsubishi 3 0 cylinder torque specs, workshop manual section 303 14, wsm 303-14a, workshop information system saab, where is the knock sensor on a 2006 toyota tundra 4 7 v-8 truck, trailblazer front frame section