po449 silverado

You search PDF repair manual about po449 silverado, if there are search results will appear below. If search results do not exist, please search by others keyword.



  po449 silverado Direct Download speed 5432 Kb/s

  po449 silverado Full Version speed 8172 Kb/s



1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

0

Filed Under (Chevrolet Manuals) by admin on 07-05-2012

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

Related Content:

acura mdx check charging system, how to drain the air conditioner on a 2003 jetta, toyota air filters pdf, where do you recharge ac on 1996 buick regal, 2007 chevy trailblazer code c0161, troubleshooting P069E, 4r100 rear carrier assembly colorado springs, tranny fluid location 2010 santa fe, chevy impala air conditioner flapper doesnt turn off, reset procedure for ride heighth 04 navigator

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 27-06-2012

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

Related Content:

wheel bearing 2004 Mountaineer, 2004 CHEVY SILVERADO TCCM, 09 silverado front axle diagram, saturn ion 3 2006 wheel nut torque, torque on 2000 tahoe front brake parts, manual silverado z71 2004, repair manual for a 95 chevy silverado, torque specs for Tahoe wheel bearing bolt, tourque specs 2003 chev truck 1500 wheels, what size is wheel hub lock nut on 2008 sierra denali

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

0

Filed Under (Chevrolet Manuals) by admin on 02-07-2012

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

Related Content:

2012malibu evap solenoid circuit condition, replace a cannister in vehicle, evap lines 98 chevy blazer, 2006 chevy monte carlo evap vent valve solenoid, replacing evap 1999 silverado, 04 suburban evap solinoid valve install video, 97grand am evap system pressure sesnsor, canaster for a 2005 yukon, fuel line routing on montana sv6, evaporate silonor valve on a 2004 chevy silvorado

Exhaust Moan/Vibration Noise (Install Exhaust System Flex Pipe Kit)

0

Filed Under (More Manuals) by admin on 10-05-2012

download
1999-2007 Chevrolet Silverado 1500 Series Extended Cab or Regular Cab/Long or Short Box Pickups (Classic) 2007-2010 Chevrolet Silverado 1500 Series Extended Cab or Regular Cab/Long or Short/Standard Box Pickups (New Body Style) 1999-2007 GMC Sierra 1500 Series Extended Cab or Regular Cab/Long or Short Box Pickups (Classic) 2007-2010 GMC Sierra 1500 Series Extended Cab or Regular Cab/Long or Short/Standard Box Pickups (New Body Style) with 4.3L Engine (VINs W, X — RPOs L35, LU3) and Automatic Transmission (RPO M30) * This bulletin is being revised to add the 2009 and 2010 model years and remove exhaust dampener installation procedures. Please discard Corporate Bulletin Number 02-06-05-003G (Section 06 — Engine/Propulsion System). Condition Some*customers*may*comment*on*a*moan*or*vibration*n oise*at*low*vehicle*speeds*40*64*km* (25*40*mph)*or*b etween*900*1700*RPM*under*load. Cause Exhaust*system*resonance*may*be*transmitted*through *the*powertrain*mounts*into*the*body* causing*this*condition. Correction

Related Content:

burning oil smell in cab of 2005 f150, gmc 5500 2007 truck wiper fuse, how to install vibirating blocks on gmc sierra

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 03-05-2012

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.

Related Content:

service manual 2005 cherolet avalanche, 2008 Cadillac Escalade repair manual, lom amf connector location 2007 suburban, 2005 chevy silverado front suspension repair manual, bcm 2002 tahoe, c1126 dtc mitsubishi pdf, Free 2005 Silverado Service Manual, how do you repair a cadillac bcm, manual for 2005 chevy silverado, repair manual for 2005 chevrolet avalanche

LM7, L59 or L33 Engines with Cold Start Rough or Incorrect Idle, Misfire, Malfunction Indicator Lamp (MIL) or Flashing Requiring O2 Sensor Replacement

0

Filed Under (More Manuals) by admin on 08-06-2011

download
2004-2005 Cadillac Escalade 2004-2005 Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe 2005 Chevrolet Silverado Hybrid (HP2) 2004-2005 GMC Sierra 1500, Yukon, Yukon XL 2005 GMC Sierra Hybrid (PH2) with Vortec 5300 5.3L V-8 Engine (VINs T, Z, B — RPOs LM7, L59, L33 Some customers may comment on a Malfunction Indicator Lamp (MIL) On or that the MIL is flashing. An actual engine misfire may or may not be felt along with an incorrect idle speed. Typically this occurs during cold winter months, on cold engine starts. Some vehicles may have been previously serviced for the same condition. Technicians may also find the following DTCs stored with the Tech 2® P0131, P0133, P0134, P0137, P0138, P0140, P0151, P0153, P0154, P0157, P1133, which may be in conjunction with P0171, P0174, P0300 and P1138. Cause Water shock occurs when water droplets are present in the exhaust. The water in the exhaust contacts the sensor element inside the HO2 sensor, causing the HO2 sensor element to crack. Correction Upon diagnostic investigation, the technician may find that the HO2 sensor requires replacement. In addition to replacing the affected HO2 sensor, these vehicles should also be reflashed with the latest PCM calibration. An updated PCM calibration will be available to dealerships as part of TIS 2000 incremental satellite update 11.0 (NAO version 25.010) or greater. Always, make sure your Tech 2 is updated with the latest software version

Related Content:

chevy suburban p0131 p0137 p0151 p0157 troubleshooting, 1999 gmc yukon repair pdf manual, 2005 cadillac rough idle during startup, 2005 chevy classic rough idel, gmc 1500xl yukon p0300, locate the air bag sensor on a 2005 escalade

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

0

Filed Under (GMC Manuals) by admin on 30-06-2012

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

Related Content:

2003 mitsubishi lancer es repair manual, 2003 chevrolet suburban ac evaporator, 2003 ford motorhome chassis repair manual, evap in 2003 chevy s10 pickup, 2003 pontiac vibe repair manual, front end diagram for a gmc 03 envoy, fuse diagram for 2003 impalaq, GMC Sierra 2003 Manual, 2002 chevrolet silverado 2500hd manual, torque specs for 2003 optima tie rod end

Special Coverage Adjustment – Instrument Panel Cluster Gauge Needle Function

0

Filed Under (More Manuals) by admin on 04-01-2012

download
2003-2004 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT 2005 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT (U.S. ONLY) 2003-2004 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE 2005 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE (U.S.ONLY) 2003-2004 GMC SIERRA, YUKON, YUKON XL 2005 GMC SIERRA, YUKON, YUKON XL (U.S. ONLY) . Install the IPC. Ensure everything is connected properly. The replacement IPC requires SPS Programming and IPC Setup procedures to be performed. It does not matter which procedure is performed first. 2. Start the engine and then select IPC Setup. You must have the engine running before performing the IPC Setup. 3. Select IPC Setup. With the engine running, enter the appropriate mileage and engine hours. 4. Select “OK”. Review the pop up asking you to verify the mileage and engine hours. Move the pop up out of the way if necessary to view the verification screen. This may require a click and drag of the dialog box. 5. Verify that the mileage and engine hours are correct and select “OK”. DO NOT turn the ignition OFF until the engine has “run” for approximately seven (7) minutes. Allowing the engine to idle for this period of time allows the IPC to accumulate 1/10th of an hour and write the correct engine hour value to the permanent memory. The engine must be running before set up is performed and run for approximately seven minutes after the user selects “OK” confirming their mileage/engine hour inputs. After approximately seven minutes, shut the engine OFF and complete the event. The seven minute clock starts after you select “OK”, confirming the entries. Note: Based on feedback from technicians, we are currently making changes to the “IPC Setup” application which will include several enhancements to the set up screens. These are scheduled to be released and available in TIS2WEB very soon. Important: Only IPC conditions listed in the Condition section of the bulletin are covered under this special coverage program. In a small number of vehicles, the condition may be intermittent and the gauge sweep test may not always verify the condition. IPC Performance IPC performance may be affected by the following conditions: Customer Comments and Observations Customers who describe gauge performance as jumpy, sticky, slow or erratic. Gauge performance may also be described as being inoperative or inaccurate. For example, for a period of time the speedometer may appear to move normally but be inaccurate and not return to zero (0) after the vehicle comes to a stop. This inaccurate condition may be more or less pronounced during the drive cycle and may, for a time, return to normal operation. A Tech 2 sweep test may not reveal the condition. 1. Perform a gauge sweep test to determine/verify that an IPC gauge is sticking, stuck, or inoperative. Using the Tech 2, navigate to the following screens to perform the gauge sweep test: Body -> Instrument Panel Cluster -> Special Functions -> IPC Gauges -> Display(s) Test. • Cold temperatures • Temperature fluctuations • High humidity • Driving over rough surfaces such as dirt roads or potholes

Related Content:

2005 cadillac escalade ext free repair manual download, 2005 escalade tailgate latch parts and accessories, tahoe 195 maintenance requirements, Specialized Speedometer Manual, specialized comp speedometer manual, reprogram instrument cluster suburban, remove inside door handle 1999 cadillac escalade, 205 cadillac escalade ext free repair manual, 2011 gmc acadia step bar installation instructions, Tahoe 195 Owners Manual

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall Service Procedure

0

Filed Under (Chevrolet Manuals) by admin on 22-11-2011

download
Why is your vehicle being recalled? Your vehicle may have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. If this happens while the vehicle is moving, a crash could result without prior warning. What will we do? Your GM dealer will replace the crankshaft position sensor. This service will be performed for you at no charge . Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual service correction time of approximately one hour and twenty minutes. What should you do? You should contact your GM dealer to arrange a service appointment as soon as possible. Bring the enclosed customer reply form with you when you visit your dealer. The form identifies the repairs required. If you no longer own this vehicle, please let us know by completing the form and mailing it back to us. Did you already pay for this repair? The enclosed form explains what reimbursement is available and how to request reimbursement if you have paid for repairs for the recall condition.

Related Content:

avanza crack pulley bolt loosening direction, will a soft whinny noise be the crank pully bolt on kia picanto

2005 Chevy Truck Silverado 1500 2WD Blower Motor Resistor Replacement

0

Filed Under (Chevy Manuals) by admin on 29-04-2012

download
Blower Motor Resistor Replacement Notes BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) . 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.

Related Content:

2005 chevy blower motor resistor ground connections, testing mazda 5 for faulty blower moror, resistor sl1, part number 05 silverado blower resistor fix, fan blower resistor for 1998 buick regal, how to change blower motor 2005 hummer h2, how to rotate resistor in schematics, NISSAN CHANGED BLOWER RESISTOR MAKING NOISE WHEN CRANK, removal/replacement of stepper motor in a 05 tahoe, removing blower motor from 2002 tundra

Related Content:

acura mdx check charging system, how to drain the air conditioner on a 2003 jetta, toyota air filters pdf, where do you recharge ac on 1996 buick regal, 2007 chevy trailblazer code c0161, troubleshooting P069E, 4r100 rear carrier assembly colorado springs, tranny fluid location 2010 santa fe, chevy impala air conditioner flapper doesnt turn off, reset procedure for ride heighth 04 navigator