programming connector for a 97 malibu

You search PDF repair manual about programming connector for a 97 malibu, if there are search results will appear below. If search results do not exist, please search by others keyword.



  programming connector for a 97 malibu Direct Download speed 5432 Kb/s

  programming connector for a 97 malibu Full Version speed 8172 Kb/s



1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, crank sensor location on 6 7 power stroke, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how to drain radiator on 2007 ford fusion 2 3 L, hino j500 pump timing marks

2003 Honda Accord EX A/ T INTERLOCK SYSTEM REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 21-01-2012

download
A/T Interlock System Circuit Diagram SHIFT LOCK SYSTEM CIRCUIT TROUBLESHOOTING 1. Press the brake pedal. Are the brake lights ON? YES -Go to step 2. NO -Repair faulty brake light circuit. 2. Connect the HDS to the DLC. Check engine speed and throttle position in the A/T data list. Is the engine speed at idle, and TPS about 0.5 V? YES -Go to step 3. NO -Repair engine speed or throttle position input. 3. Select SHIFT LOCK SOL TEST in MISC. TEST MENU, then carry out shift lock solenoid function test. Does the shift lock solenoid work properly? YES -System circuit is OK. Check the shift lock mechanism, if necessary. NO -Go to step 4. 4. Remove the center console (See CENTER CONSOLE REMOVAL/INSTALLATION ). 5. Disconnect the shift lock solenoid connector. 6. Turn the ignition switch ON (II). 7. Measure the voltage between No. 1 terminal of the shift lock solenoid connector and body ground. Fig. 3: Measuring Voltage Between No. 1 Terminal Of Shift Lock Solenoid Connector & Body Ground Is there battery voltage? YES -Go to step 8. NO -Check for blown No. 21 fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the shift lock solenoid connector and the under-dash fuse/relay box. 8. Shift the shift lever into the P position, and press the brake pedal. Do not press the accelerator. 9. Measure the voltage between shift lock solenoid connector terminals while pressing the brake pedal Fig. 4: Measuring Voltage Between Shift Lock Solenoid Connector Terminals Is there battery voltage? YES -Check the shift lock mechanism. If the mechanism is OK, replace the shift lock solenoid (see Shift Lock Solenoid Replacement ). NO -Check for poor or loose PCM connector terminal E2 at the PCM, and check for an open in the wire between PCM connector terminal E2 and shift lock solenoid connector. If the connection and wire is OK, substitute a known-good PCM and recheck. KEY INTERLOCK SYSTEM CIRCUIT TROUBLESHOOTING

Related Content:

honda 2005 solenoid c, cavalier selenoide tcc, 2002 mdx shift interlock broken, relay trasmission control on cavalier 2003, 2003 hummer H2 transmission shift connection, transmisson speed sencer on 2000 f150 how do you change it, lincoln continental p0743, 1998 F-150 Electronic Pressure Control Solenoid Short Circuit, how to install transmission shift solenoid buick regal ls 2000, replace shift solionide on honda crv 1999

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Related Content:

how do i install ignition switch on 1996 chevy pickup, how to replace a 1990 Toyota Corolla Ignition switch, g6 testing key switch, 2007 chevy silverado brake switch installation, what causes 2005 toyota sienna starter relay to burn out, how to take ignition switch out of kia sorento, how toremuve thh ignition key on chrysler 2002 concord LX1 or baypass, ignition switch removal on 2003 buick century, ignition switch wiring diagram 2006 chevrolet uplander, where is ignition switch 01 silverado

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

mitsubishi canter (4D35) repair manual pdf, starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram

2001 Dodge Dakota CENTRAL TIMER MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 28-06-2012

download
1. Connect scan tool to Data Link Connector (DLC), under lower left side of instrument panel. Turn ignition on. Using scan tool, attempt to communicate with Air Bag Control Module (ACM) and Controller Antilock Brake (CAB) module. If scan tool is able to identify or communicate with ACM and CAB, go to next step. If scan tool is not able to identify or communicate with ACM and/or CAB, perform appropriate DTC or symptom test. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION and SYMPTOM IDENTIFICATION tables under SELF-DIAGNOSTIC SYSTEM. 2. Turn ignition off. Disconnect Gray 26-pin Central Timer Module (CTM) connector C1. CTM is located behind left side kick panel. Ensure interior lights are off. Using DVOM, measure resistance between ground and Gray 26-pin CTM connector C1 terminals No. 1 and 16 (Black/Light Green wires) and No. 2 (Black wire). See Fig. 5 . If resistance is 10 ohms or less on each ground circuit, go to next step. If resistance is more than 10 ohms on any ground circuit, check for an open between appropriate CTM connector terminal and ground. See GROUND DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 3. Disconnect Gray 12-pin CTM connector C3. Using test light connected to ground, probe Gray 12-pin CTM connector C3 terminals No. 1 (Red/Tan wire) and No. 6 (Red/Light Green wire). See Fig. 8 . If test light illuminates on both circuits, go to next step. If test light does not illuminate on both circuits, check for open in appropriate circuit between power distribution center and CTM. See POWER DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 4. Turn ignition on. Using scan tool, ensure there is PCI BUS communication with other modules (besides the ACM and CAB). If scan tool is able to identify or communicate with all modules, go to next step. If scan tool is not able to identify or communicate with all modules, refer to appropriate communications symptom for diagnosis. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION table under SELF-DIAGNOSTIC SYSTEM. 5. Connect Scope Input Cable (CH7058) to channel one connector on scan tool. Connect Cable-To-Probe Adapter (CH7062) and Black and Red test probes to scope input cable. Connect Black test probe to ground. Connect Red test probe to PCI BUS circuit at Gray 26-pin CTM connector C1 terminal No. 10 (Violet/Yellow wire). 6. Using scan tool, select PEP MODULE TOOLS, LAB SCOPE, LIVE DATA. Select 12 VOLT SQUARE WAVE. Press F2 for SCOPE. Press F2 and use DOWN arrow to set voltage scale to 20 volts. Press F2 again when complete. Turn ignition on. If reading on lab scope toggles between zero and 7.5 volts, go to next step. If reading on lab scope does not toggle between zero and 7.5 volts, repair open in PCI BUS circuit (Violet/Yellow wire). 7. Replace CTM. See CENTRAL TIMER MODULE under REMOVAL & INSTALLATION

Related Content:

2001 dodge ram central timer module location, can you repair a central timer unit?, 2000 mazda mpv p0755 code Broken wire, UT Scan Plan, scan tool will not communicate for air bag codes, programing a CTM, ct 20 turbo diagram, control time module rear bumper for 2002 dodge dakota, central timer module 2003 Dodge Dakota replacement, central time moduale dodge durango 2001

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

0

Filed Under (Chevrolet Manuals) by admin on 10-01-2012

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

Related Content:

diagram for ignition wires on a 1998 sebring 2 5l, replac upper valve cover gasket 2005 chevy malibu maxx 3 5, Owners Manual 2004 Chevy Malibu Maxx, malibu ml60t manual, how to replace a ignition coil on 2004 toyota sienna, repair of saab ignition coil, mazda speed 6 ignition module, firing order for a 2006 chevy malibn maxx, 1999 saturn replacement ignition switch bolts, 2006 pontiac torrent replacement ignition

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, p0753 kia rio 2004, canter 4d 35 interval wiper control relay, wiring diagram for mitsubishi canter ignition, what is the tcc solenoid on a 2 2 cavalier, Powertrain Generator 6500 Parts Diagram, Kia Rio 2001 DTC P0753, bully side ste for jeep instructions, 2006 pontiac g6 gt code po753, 4t80e tcc solenoid replacement

200-92010 Toyota Camry/ Corolla OE Fit Fog Light Install Instruction

0

Filed Under (Toyota Manuals) by admin on 28-04-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties. 2. Attach the ring terminal with 2 black wires to the 10mm bolt next to the relay 3. Connect the ring terminal from the relay (12v red wire) to the positive terminal of the battery 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector. Seal with 3M Silicone sealant (see picture 1) Picture 1 5. Run the fog light wire harness on the driver side of the car. Use wire ties as needed. 6. Remove dash panels 7. Mount switch into switch knockout on left side of dash 8. From inside the cabin, locate the small connector that were pushed through in step 4. It will be the grommet above the gas pedal 9. Install switch harness 10. T-tap green/black wire from fog light harness to connector E21 pin 11, light green wire (first pin on right). Connector E21 is located on the left side of the steering column (picture 2) Picture 2 11. T-Tap orange/black wire from fog light harness to connector ID pin 3, pink wire (middle third pin from left). Connector ID is left of steering wheel (picture 3) Picture 3 12. Secure with wire ties. 13. Reinstall dash panels 14. Route the fog light wire under car. 15. Remove fog light cover plates and lower splash shields on both sides 16. Insert one side of the fog light into the plastic sleeve and secure other side with supplied Phillip screws (see picture 4

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, crank sensor location on 6 7 power stroke, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how to drain radiator on 2007 ford fusion 2 3 L, hino j500 pump timing marks