Skip to content

pt cruiser front engine splash shield

You search PDF repair manual about pt cruiser front engine splash shield, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine Fuel Pump Resistor Service Procedure

download
The following are instructions for removing the fuel pump resistor from its original mounting location on the lower right front body rail as shown in Figure 1, and replacing it with a new fuel pump resistor and cover in new location shown in Figure 2. The new location is on the front of dash sheet metal (3) at the rear of the engine compartment, inboard or to the left of the alternator (4). The passenger or right side windshield wiper arm (5) and stop (6) are called out for reference purposed only. 1. Turn the steering wheel to the full right position. 2. Open the hood and disconnect the negative battery cable. 3. Remove the diagonal brace (1) from over the windshield washer solvent reservoir by removing the two bolts (2) that attach it to the radiator support and the one bolt (3) that attaches it to the strut tower. Refer to Figure 3 4. Remove the two plastic push-in retainers (1) that attach the windshield washer solvent reservoir (2) to the radiator support (3) and the one nut (4) that attaches it to the strut tower (5). Refer to Figure 4. 5. Reposition the reservoir for access to the area rearward of the battery. 6. Raise the vehicle on a hoist. 7. At the right front wheel opening, remove the three screws that attach the inner fender splash shield to the front fascia at the wheel opening and the two screws that attach it to the bottom of the fascia. Refer to Figure 5. 8. Reposition the inner fender splash shield (1) to access the fuel pump resistor (2). Refer to Figure 1 at the beginning of this procedure. 9. Unclip the fuel pump resistor electrical connector from the body and disconnect the connector. 10. Remove the 10mm hex head bolt attaching the fuel pump resistor to the body and discard both the bolt and the resistor.

1997 Chrysler Sebring JXi TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
1. Disconnect negative battery cable from jumper terminal. Raise and support vehicle. Remove right front wheel. Remove accessory drive belt splash shield from right wheelwell. 2. Remove accessory drive belts. Remove right engine support assembly vertical bolts from bottom side of frame rail (timing belt end of engine). 3. Lower vehicle. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine support assembly to engine block bracket. 4. Move the A/C drier aside with hoses attached. Remove coolant reservoir tank. Remove right engine support assembly. Remove 3 bolts attaching engine support bracket to engine block, and remove bracket. 5. Remove crankshaft vibration damper. Remove power steering pump (hoses attached) and bracket from engine block. Remove timing belt covers. 6. Rotate crankshaft to align camshaft and crankshaft timing marks. 7. If reusing old timing belt, mark timing belt direction of rotation for installation reference. Loosen timing belt automatic tensioner bolts. Remove timing belt. Remove automatic tensioner. Installation 2.5L VIN H (Cirrus, Sebring Convertible & Stratus) 1. Place automatic tensioner into vise, and SLOWLY compress plunger. When plunger is compressed into tensioner body, install locking pin through body and plunger holes to retain plunger until tensioner is installed. See Fig. 13 . 2. Index tensioner in vise the same direction as installed. This will ensure proper pin orientation when tensioner is installed in engine.

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

1999 Ford Crown Victoria/ Grand Marquis Instrument Panel and Console Removal/ Installation Manual

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the driver side air bag module. For additional information, refer to Section 501-20B . 2. Remove the passenger side air bag module. For additional information, refer to Section 501-20B . 3. Close the glove compartment. 4. Position the speed control servo aside. 1. Disconnect the electrical connector. 2. Remove the nuts. 3. Position the speed control servo aside. 5. Disconnect the LH engine compartment in-line electrical connector. * Release the wiring harness locators. 6. Disconnect the brake fluid sensor electrical connector. 7. Disconnect the windshield wiper motor electrical connector. * Release the wiring harness locators. 8. Disconnect the LH engine compartment in-line electrical connectors. 9. Unseat the LH wiring harness grommet 10. Disconnect the blower motor electrical connector. 11. Disconnect the A/C pressure cut-off switch electrical connector. 12. Disconnect the RH engine compartment in-line wiring harness connectors. 13. Disconnect the vacuum line at the intake manifold. 14. Disconnect the electronic air temperature control (EATC) variable blower motor controller electrical connector. * Release the wiring harness locators. 15. Remove the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 16. Remove the upper front fender splash shield bolts. 17. Remove the lower front fender splash shield bolt and locator. 18. Position the front fender splash shield away from the dash panel. 19. Unlock the wiring harness guide. 20. Unseat the RH wiring harness grommet. 21. Install the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 22. Remove the RH instrument panel lower insulator. 1. Remove the pin-type retainers. 2. Release the locking tab. 3. Remove the instrument panel lower insulator. * Disconnect the courtesy lamp.