Skip to content

pump overhauling procedure

You search PDF repair manual about pump overhauling procedure, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine Fuel Pump Resistor Service Procedure

download
The following are instructions for removing the fuel pump resistor from its original mounting location on the lower right front body rail as shown in Figure 1, and replacing it with a new fuel pump resistor and cover in new location shown in Figure 2. The new location is on the front of dash sheet metal (3) at the rear of the engine compartment, inboard or to the left of the alternator (4). The passenger or right side windshield wiper arm (5) and stop (6) are called out for reference purposed only. 1. Turn the steering wheel to the full right position. 2. Open the hood and disconnect the negative battery cable. 3. Remove the diagonal brace (1) from over the windshield washer solvent reservoir by removing the two bolts (2) that attach it to the radiator support and the one bolt (3) that attaches it to the strut tower. Refer to Figure 3 4. Remove the two plastic push-in retainers (1) that attach the windshield washer solvent reservoir (2) to the radiator support (3) and the one nut (4) that attaches it to the strut tower (5). Refer to Figure 4. 5. Reposition the reservoir for access to the area rearward of the battery. 6. Raise the vehicle on a hoist. 7. At the right front wheel opening, remove the three screws that attach the inner fender splash shield to the front fascia at the wheel opening and the two screws that attach it to the bottom of the fascia. Refer to Figure 5. 8. Reposition the inner fender splash shield (1) to access the fuel pump resistor (2). Refer to Figure 1 at the beginning of this procedure. 9. Unclip the fuel pump resistor electrical connector from the body and disconnect the connector. 10. Remove the 10mm hex head bolt attaching the fuel pump resistor to the body and discard both the bolt and the resistor.

Ford 455C 555C 655C Tractor Loader Backhoe Service Manual

download
Engine Systems Chapter 1 3-Cylinder Diesel Engine 3-Cylinder Diesel Engine – Description and Operation 3-Cylinder Diesel Engine – Overhaul Chapter 2 4-Cylinder Diesel Engine 4-Cylinder Diesel Engine – Description and Operation 4-Cylinder Diesel Engine – Overhaul Chapter 3 Cooling System Cooling System – 3-Cylinder Engine Description and Operation Cooling System – 4-Cylinder Engine Description and Operation Cooling System – Overhaul Chapter 4 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 2 Fuel Systems Chapter 1 Fuel System – General Fuel System – Description and Operation Fuel System – Adjustments DPA Distributor Type Fuel Injection Pump Fuel System – Adjustments DPS Distributor Type Fuel Injection Pump Fuel System – Fuel Tanks, Filters and Fuel Lines Overhaul Chapter 2 Fuel Injection Pump – DPA Distributor Type Fuel Injection Pomp – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedures Chapter 3 Fuel Injection Pump – DPS Distributor Type Fuel Injection Pump – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedure Chapter 4 Injectors Ford 455C Injectors – Description and Operation Injectors – Overhaul Chapter 5 Injectors Ford 555C and 655C Injectors – Description and Operation Injectors – Overhaul Chapter 6 Air Cleaners Dry Type Air Cleaner – Description and Operation Dry Type Air Cleaner – Overhaul Chapter 7 Turbocharger Turbocharger – Description and Operation Turbocharger – Overhaul Chapter 8 Troubleshooting, Specifications, Test Plans and Special Tools Troubleshooting – Diesel Engines Troubleshooting – Turbocharger Specifications Special Tools Test Plans Part 3 Electrical System Chapter 1 Wiring, Lights and Controls Wiring, Lights and Controls – Description and Operation Wiring, Lights and Controls – Fault Finding and Repair Circuit Diagrams and Wiring Harness Chapter 2 Battery
Battery – Description and Operation Battery – Maintenance and Tests Chapter 3 Starting System Starting System – Description and Operation Starting Motor – Overhaul Chapter 4 Charging System – A127 55 Amp Alternator with Integral Regulator Charging System – A127 55 Amp Alternator with Integral Regulator – Description and Operation Charging System – A127 55 Amp Alternator with Integral Regulator – Service Precautions, Preliminary Checks, Initial Tests and Alternator Component Tests Charging System – A127 55 Amp Alternator with Integral Regulator – Overhaul Chapter 5 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 4 Power Reversing Transmission Chapter 1 4×4 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul Chapter 2 8X8 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit, Lockup Valves and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul

1998-2003 FORD ENGINE 7.3L DIESEL DI HIGH PRESSURE OIL PUMP LEAK REPAIR MANUAL

download
ENGINE 7.3L DIESEL DI HIGH PRESSURE OIL PUMP LEAK ACTION sensor electrical connector. High pressure oil pump leaks at the outlet fittings b. Remove the exhaust back pressure sensor. and/or end plug can be serviced without removing the pump assembly. Replace the O-rings on the 3. Remove the high pressure oil pump reservoir. fittings and the end plug using Kit 2C3Z-9G804-AA. For additional information, refer to Section All three (3) O-rings should be replaced. Apply 303-04 in the appropriate Workshop Manual. liquid thread sealer (included in the kit) prior to WARNING reinstallation. Refer to the following Service Procedure for details. SMOKING OR OPEN FLAME OF ANY TYPE MUST NOT BE PRESENT WHEN WORKING SERVICE PROCEDURE NEAR FUEL VAPOR. NOTE CAUTION BEFORE PERFORMING THE REPAIR THE FUEL SYSTEM CONTAINS PRESSURIZED PROCEDURE, MAKE SURE THAT THE CAUSE FUEL AFTER THE VEHICLE IS SHUT DOWN OF THE LEAK IS CLEARLY ESTABLISHED. AND WILL MAINTAIN THIS PRESSURE FOR A LONG PERIOD OF TIME. NOTE FOR E-SERIES AND F650/750 VEHICLES, 4. Open the fuel/water separator drain valve to FOLLOW THE PROPER HIGH PRESSURE OIL release fuel pressure. Completely drain the fuel PUMP ACCESS PROCEDURE IN THIS filter/water separator assembly. DOCUMENT FOR ACCESS TO THE HIGH 5. Disconnect the fuel supply and fuel return lines PRESSURE OIL PUMP. from the fuel filter/water separator. NOTE 6. Disconnect the two (2) cylinder head fuel FOR SUPER DUTY AND EXCURSION, PROCEED supply lines from the fuel filter/water separator

2009 Ford Escape 3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/ THUMP NOISE SERVICE PROCEDURE

download
3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/THUMP NOISE This article supersedes TSB 09-11-6 to update the b. Isolate noise to LH – Listen to the cylinders Service Procedure and Part List. 4 and 6 valve cover fasteners (number 6 is by the coolant pump). There will be a ISSUE significant difference in transmitted noise Some 2009 Escape and Mariner vehicles, equipped between the cylinder 4 and 6 fasteners with 3.0L engine, may exhibit an intermittent when noise is present. Noise from LH – go knocking or thumping type noise from the cylinder to Step 4. head. After engine temperature reaches 210-220 °F NOTE (99-104 °C), the noise is typically heard from the THE RH AND LH NOISES HAVE DIFFERENT rear of the engine as the vehicle comes to a stop. CAUSES. FOLLOW ALL STEPS CAREFULLY FOR An example would be coming to a stop at the end PROPER DIAGNOSIS AND REPAIR. of a highway exit ramp. Noise will continue 45-60 seconds and then diminish. Noise will occur again 3. Replace the RH cylinder head per Workshop once engine reaches 210-220 °F (99-104 °C) and Manual (WSM), Section 303-01B. vehicle comes to another stop. a. Verify repair by repeating Step 2. If noise is ACTION still present then proceed with normal Follow the Service Procedure steps to correct the engine NVH diagnostics per WSM, Section condition. 100-04. SERVICE PROCEDURE 4. Remove LH valve cover. Refer to WSM, Section 303-01. 1. Is noise a 45-60 second knock/thump from a hot engine as the vehicle comes to a stop? a. Rotate the engine clockwise until cylinder number 6 exhaust cam lobes are pointing a. Yes – Go to Step 2. up and valves are fully closed. Exhaust camshaft needs to be left in this position for b. No – Stop as this procedure does not apply. all bearing caps in Step 4b. (Figure 1) Proceed with normal Workshop Manual (WSM), Section 100-04 diagnostics. 2. Using Chassis Ears, isolate the noise to Right Hand (RH) (Bank 1) or Left Hand (LH) (Bank 2) cylinder head. Noise is typically heard as 45-60 second knock/thump as the vehicle comes to a stop after engine reaches 210-220 °F (99-104 °C). a. Isolate noise to RH – Listen to the cylinder head by the variable camshaft timing (VCT) solenoid connectors. There will also be a vibration felt at the VCT solenoid connector when noise is present. Noise from RH – go to Step 3.

2004-2007 Ford Explorer MIL ON WITH DTC P0463 OR ERRATIC FUEL GAUGE OPERATION SERVICE PROCEDURE

download
ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. For vehicles with customer symptom of erratic fuel gauge operation (with no MIL on), proceed to Step 1a. For vehicles with a customer symptom including the MIL on, proceed to Step 1b. If unable to verify the concern, do not continue with this TSB. a. Follow the appropriate pinpoint test (PPT) for “Fuel Gauge Inaccurate” in Workshop Manual (WSM), Section 413-01. If PPT test results lead to fuel pump module replacement, proceed to Step 2. If PPT test results isolate any problem other than fuel pump module replacement, repair as indicated and do not continue with this TSB. b. Install diagnostic scan tool to retrieve DTCs. If DTC P0463 is retrieved, proceed to Step 2. If DTC P0463 is not retrieved, this TSB does not apply, follow normal WSM diagnostics. 2. Remove fuel tank per WSM, Section 310-01 3. Remove fuel pump assembly from fuel tank per WSM, Section 310-01. See Figure 1 (Chart) to determine if a kit (contains a fuel level sensor assembly, a wire harness and heat shrink tube) or fuel pump assembly is required for repair. For vehicles that can be serviced with a kit go to Step 4. For vehicles that require fuel pump assembly replacement, go to Step 12. 4. Remove the fuel level sensor assembly (sender card/float rod assembly) from the fuel pump assembly per WSM, Section 310-01