radio wiring diagram for a 2000 mazda protege

You search PDF repair manual about radio wiring diagram for a 2000 mazda protege, if there are search results will appear below. If search results do not exist, please search by others keyword.



  radio wiring diagram for a 2000 mazda protege Direct Download speed 5432 Kb/s

  radio wiring diagram for a 2000 mazda protege Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, dodge durango 2002 suspension layout, zimmatic pivot wiring, 2003 s10 airbag wiring diagram, lazy boy recliner mechanism diagram, 2000 Buick LeSabre Wiring Diagram

2009 Toyota Corolla DASH DISASSEMBLY INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-05-2011

download
1 Unclip and remove the (4) side trim panels from the right and left side of the radio and a/c controls. ( Figure A) 2 Unclip and remove the a/c vent panel above the factory radio. (Figure B) 3 Remove (4) 10 MM bolts securing the radio. (Figure C) 4 Remove (4) plastic clips from the back of the factory radio. (Retain the clips for re-use during kit assembly.) 5 Continue to kit assembly . A B C 99-8223 KIT ASSEMBLY 2 A B C D DIN RADIO WITH POCKET PROVISION Slide the Radio Housing Brackets onto the sides of the Radio Housing until the side clips engage. NOTE: Tabs are marked Left and Right. (Figure B) 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure C) 3 Slide the aftermarket radio into the cage until it snaps into place. (Figure D) 4 Attach the clips removed from the factory radio to the back of the radio housing trim plate. (Figure A) 1 Continue to final assembly . * Note: Refer also to the instructions included with the aftermarket radio. 99-8223 KIT ASSEMBLY 3 A B C D ISO MOUNT RADIO WITH POCKET PROVISION Slide the Radio Housing Brackets onto the sides of the Radio Housing until the side clips engage. NOTE: Tabs are marked Left and Right. (Figure B) 2 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure C) 3 Slide the radio into the radio housing until it snaps into place. (Figure D) 4 Snap the Trim plate onto the front of the Radio Housing. (Figure D) 5 Attach the clips removed from the factory radio to the back of the radio housing trim plate. (Figure A) 1 Continue to final assembly .

Related Content:

Honda CRV Fuse Chart sample, 2003 isuzu npr cabover wiring diagrams, remove radio knob on 2004 chevy avalanche, 2002 bmw 325i wiring diagrams, how to replace bravada stereo knobs, how to replace the radio in a 2004 nissan quest, new 2001 ford focus radio trim bezel part #98aba046a04cgw, Replacement Radio 2004 Chevy Silverado, stereo wiring diagram for 2012 chevy sonic, clk 500 radio fuse

Toyota Corolla Upgrading a car radio

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
step 1: Preparing the wiring harness Get a wiring harness or adapter that will allow the car radio wiring to plug into the back of the new radio. These can be found at Walmart for $4.99. Make sure that the plug is compatible with your car (check the list on the back of the box). Have shown the back of the new radio – the black set of pins is where the included black plug will go to. The free wires on the black plug provided with the new audio system will be connected to an adapter that will plug into the car wiring. For the Toyota Corolla 1995 wagon, the wiring diagram is as shown below. Your car may differ substantially from this step 2: Connecting the wires Connect the wires from the plug that came with the new radio to the wiring harness adapter that you purchased separately. Twist the correct wires together and then solder them (or use wire nuts if you dot have soldering equipment). Cover the exposed wire with electricians tape or heat seal tape. Attached is another table on how you connect your Toyota wiring adapter to the radio plug. Please, do remember that your radio and car will differ a bit step 3: Removing the old radio Remove the factory installed radio (the instructions apply only for Corollas from 95-98). Remove the two screws below the panel. Have shown a picture with the location of these screws. Remove the control knobs for the AC and the fan, etc. These come off pretty easily with a gentle pull. Use a thin blade (metal spatula) to probe approximately 2/3rd of the way up and try to pry the sides out. The metal blade will disengage the clip on each side. Took a bit of gentle effort but it did pop out. The location of these clips is just below the vents. Lift the panel up, reach under it to carefully remove the plugs on the right hand side that connect the defroster, the clock and the hazard flasher. The plugs can be removed by squeezing a release tab on the plug and then gently pulling them apart. Remove the radio – two pairs of screws on each side of the radio hold it in place. Remove these (and hold onto them because you will need them later on) and then slide the radio out.

Related Content:

wiring diagrams PDF 2008 town car

Dodge AUDIO SYSTEMS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Dodge Manuals) by admin on 07-06-2011

download
REMOVAL (1) Disconnect and isolate the battery negative cable. (2) Remove the cluster bezel from the instrument panel. Refer to Cluster Bezel in the Removal and Installation section of Group 8E-Instrument Panel Systems for the procedures. (3) Remove the two screws that secure the radio receiver to the instrument panel (Fig. 4). (4) Pull the radio receiver out from the instrument panel far enough to access the instrument panel wire harness connectors and the antenna coaxial cable connector (Fig. 5). (5) Disconnect the instrument panel wire harness connectors and the antenna coaxial cable connector from the receptacles on the rear of the radio receiver. (6) Remove the radio receiver from the instrument panel. Fig. 4 Radio Receiver Remove/Install 1-WIRE HARNESS 2-RADIO 3-SCREW 8F-10 AUDIO SYSTEMS DN DIAGNOSIS AND TESTING (Continued)INSTALLATION (1) Position the radio receiver to the instrument panel. (2) Reconnect the instrument panel wire harness connectors and the antenna coaxial cable connector to the receptacles on the rear of the radio receiver. (3) Position the radio receiver into the mounting hole in the instrument panel. (4) Install and tighten the two screws that secure the radio receiver to the instrument panel. Tighten the screws to 5 N·m (45 in. lbs.). (5) Install the cluster bezel onto the instrument panel. Refer to Cluster Bezel in the Removal and Installation section of Group 8E-Instrument Panel Systems for the procedures. (6) Reconnect the battery negative cable. REMOTE RADIO SWITCH WARNING: ON VEHICLES EQUIPPED WITH AIR- BAGS, REFER TO GROUP 8M-PASSIVE RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIR- BAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY. REMOVAL (1) Disconnect and isolate the battery negative cable. (2) Remove the driver sideairbagmodule from the steering wheel. Refer to Driver Side Airbag Module in the Removal and Installation section of Group 8M-Passive Restraint Systems for the procedures. (3) Remove the speed control switch located on the same side of the steering wheel as the remote radio switch that is being serviced. Refer to Speed Con- trolSwitches in the Removal and Installation sec- tionofGroup 8H-Speed Control System for the procedures. (4) Disconnect the steering wheel wire harness connector from the connector receptacle of the remote radio switch (Fig. 6). (5) Disengage the four remote radio switch latches that secure the switch to the inside of the mounting hole in the steering wheel rear trim cover. Fig. 5 Radio Receiver Connections -Typical

2009 Toyota Corolla Radio With Pocket INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 15-05-2011

download
Unclip and remove the (4) side trim panels from the right and left side of the radio and a/c controls. ( Figure A) 2 Unclip and remove the a/c vent panel above the factory radio. (Figure B) 3 Remove (4) 10 MM bolts securing the radio. (Figure C) 4 Remove (4) plastic clips from the back of the factory radio. (Retain the clips for re-use during kit assembly.) 99-8223 KIT ASSEMBLY 2 A B C D DIN RADIO WITH POCKET PROVISION Slide the Radio Housing Brackets onto the sides of the Radio Housing until the side clips engage. NOTE: Tabs are marked Left and Right. (Figure B) 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure C) 3 Slide the aftermarket radio into the cage until it snaps into place. (Figure D) 99-8223 KIT ASSEMBLY 3 A B C D ISO MOUNT RADIO WITH POCKET PROVISION Slide the Radio Housing Brackets onto the sides of the Radio Housing until the side clips engage. NOTE: Tabs are marked Left and Right. (Figure B) 2 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure C) 3 Slide the radio into the radio housing until it snaps into place. (Figure D) 4 Snap the Trim plate onto the front of the Radio Housing. (Figure D) 5 Attach the clips removed from the factory

1999 Toyota Corolla Radio Replacement

0

Filed Under (Toyota Manuals) by admin on 12-05-2011

download
The radio is secured to the frame of the vehicles dash with screws located behind the plastic dash panel surrounding the radio. This plastic dash panel unsnaps from the body of the vehicles dash. STEP 2 : The bottom of the plastic dash panel, just below the bottom of the radio, can be lifted up. Look up from the below the radio and you will notice rectangular openings or insertion points where a flat tool can be inserted to pry out the bottom of the plastic dash panel. With a flat head screwdriver or other flat object, pry out the bottom of the plastic dash panel STEP 3 : Once the bottom edge of the plastic dash panel has been pulled out, the sides of the plastic dash panel will begin to separate from the body of the vehicles dash. You will now be able to put your fingers into the openings on the sides of the plastic dash panel. Gently pull the plastic dash panel until it unsnaps from the body of the vehicles dash. Remove Factory Radio Move to: Wire New Radio Section Wiring The New Radio Move to: Mounting New Radio Section The Install Doctor STRONGLY recommends purchasing a ‘DIN’ radio for this vehicle. ‘DIN’ radios are a direct replacement for the Toyota radio in this vehicle. More information is available in the Mounting New Radio section. Mounting The Radio Options STEP 4 : Once all the clips on the plastic dash panel have been unsnapped, the dash can be pulled out. The top of the plastic dash panel will have wires attached to the clock, hazard and defrost switches. You do NOT need to unplug the connectors plugged into them. Move the plastic dash panel up and set it on top of the body of the dash. STEP 5 : The radio is held in with four (4) phillips screws / 8 mm bolts . Remove the screw/bolts. Pull the radio forward. Unplug the antenna cable, and 2 white connectors from the rear of the radio

Related Content:

toyota venza dashboard repair manual, Plastic Bezel Watch Instructions, 1995 ford 555d backhoe dashboard warning light, tsb #00-25-6, set hino dashboard clock, plastic bezel 1011 watch manual, no sienna dash lights, how to renove upper dah panel 2013 avalon, how install 2001 camaro dash panel, hino 268 dash warning lights

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 buick century service manual free, 2000 saturn sl1 owners manual, 560sl repair 1988, 2000 Chevy Impala Passkey Bypass is there a fuse, diagrama buick century 2002 pmc, park avenue ac control schematic, is it hard to replace the ac compressor on a 2001 mercury cougar 2 5l 12valve car, 2000 chevrolet suburban haynes

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

2009-2010 Toyota Venza DIN Head Unit Provision With Pocket Installation Manual

0

Filed Under (Toyota Manuals) by admin on 26-02-2012

download
Toyota Venza 2009-2010 1 D isconnect the negative battery terminal to prevent an accidental short circuit. 1 Unclip and remove the trim panel to the right of the shifter. ( Figure A) 2 Remove (1) Phillips screw from the bottom of the climate control then unclip and remove the climate control. (Figure B) 3 Remove (4)10 MM bolts securing the radio. Note: You will need a universal swivel head socket adapter to get to the bottom left bolt. (Figure C) 4 Remove (4) Phillips screws securing the factory radio to the a/c vent panel. ( Figure D) 5 A B C REAR VIEW-RADIO AND A/CVENT PANEL RADIO D Continue to kit assembly . 99-8225G KIT ASSEMBLY 2 REAR VIEW-A/C VENT PANEL A B C D Secure the Radio Housing into the factory a/c vent panel using the factory hardware. (Figure A) 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the aftermarket head unit into the cage and secure. (Figure C) 4 * Note: Refer also to the instructions included with the aftermarket radio. DIN HEAD UNIT PROVISION WITH POCKET Reassemble remaining radio and dash assemblies in reverse order of disassembly. 5 6 Snap the factory vent panel/Radio Housing over dash cavity. (Figure D) 99-8225G KIT ASSEMBLY 3 REAR VIEW-A/C VENT PANEL A B C D Secure the Radio Housing into the factory a/c vent panel using the factoryhardware. (Figure A) 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 2 Slide the head unit into the radio opening until the side clips engage. (Figure C) 3 Snap the Trim Plate into the Radio Housing. (Figure C) 4 * Note: Refer also to the instructions included with the aftermarket radio. ISO DIN HEAD UNIT PROVISION WITH POCKET 5 Snap the factory vent panel/Radio Housing over dash cavity. (Figure D) Reassemble remaining radio and dash assemblies in reverse order of disassembly

Related Content:

metra bbbpc wiring diagram, code fortuner head unit, metra bbbpc, toyota venza 2009 manual

DICE iPod Integration Kit for Toyota Radio Interface Kit.

0

Filed Under (Toyota Manuals) by admin on 19-06-2011

download
1. Pull vehicle into service bay and access radio/center console. 2. Disconnect both battery terminals. These cables must be disconnected during installation to insure proper initialization of the DICE module when the DICE when it is connected. 3. Pull out the vehicle’s radio by removing any required trim and screws. 4. Some trim may need to be removed before the radio can be taken out. 5. MostToyota vehicles use clips to hold the trims in place. Most panels can be removed with little pressure using no tools Remove any screws holding the radio in place, so the radio may be fully removed. A10mm socket wrench will be needed to remove these screws. 7. Connect the vehicle specific cable’s 8-pin molex and iPod Docking Cable to the DICE module. The correct plugs on the DICE module can be identified by matching it up with the connector or by looking for the label on the bottom of the module. connector 1/8″ AUX Dock Cable Vehicle Specific Cable 6 7 5. Shown is the CD Changer harness from the back of the radio. The vehicle specific cable will be interfacing from this point. Some radios may have the connectors in a different order than shown. Match up the DICE vehicle specific cable to the connector on the back of the radio. 6 b. If the vehicle is equipped with Sirius/XM satellite radio, then this connector will already be occupied. Disconnect and reconnect it to the optionalToyota Cable. a. For late modelToyotas using the optional Toyota Cable, the extra plug on theToyota interface cable will not be used. a b
4 9. Verify all connections and re-install the radio back into the vehicle by sliding it into the tray until it locks into place. Route the docking cable as desired. The DICE iPod Integration installation is now complete. Use caution around the factory wiring while reinstalling your radio. If the radio will not slide into place, do not try to force it in place. Pull the radio back out and check for any cables or other obstructions that may be in the path of the radio. 9 This documentation Keep away from children ! Proof of purchase is required. is provided as an educational guide only and all included content, including written information and images, is as is. No warranty explicit or implied is stated and neither DICE Electronics LLC., nor any of its distributors, dealers or vendors shall be liable for any damages. Driving is dangerous and requires concentration. Do not allow the DICE iPod Integration Kit to distract you from prevailing traffic conditions. If in doubt, only operate the unit when stationary or ask a passenger to operate it for you. Do not submerge or expose to water or other fluids. DICE components are NOTwater resistant and will be damaged by water. You must properly insulate its casing if your installation environment may subject the unit to water, such as a convertible vehicle. DICE components may contain small parts, can be broken or disassembled and components may become loose from vibration and heat. Small components and packaging materials may be a choking hazard when handled by children.

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, dodge durango 2002 suspension layout, zimmatic pivot wiring, 2003 s10 airbag wiring diagram, lazy boy recliner mechanism diagram, 2000 Buick LeSabre Wiring Diagram