Skip to content

rear speaker not working ford expedition 2000

You search PDF repair manual about rear speaker not working ford expedition 2000, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

2000 Ford F-Super Duty 250-550/ Excursion/ F-53 Motorhome Chassis Workshop Manua

download
Removal 1. Set the parking brake. 2. Loosen the retaining bolts. 3. Raise the vehicle to the desired working height, keeping the axle parallel with the floor; for additional information, refer to Section 100-02 . 4. Release the parking brake. 5. Remove the wheel(s); for additional information, refer to Section 204-04 . 6. Remove the brake caliper and rotor on the single rear wheel axle; for additional information, refer to Section 206-04 . 7. Remove the retaining bolts and axle shaft. 9. d the hub nut if es apart during removal. no circumstances e operations. NOTE: The hub nut will ratchet during this operation. Remove the hub nut (counterclockwise for right-hand thread; clockwise for left-hand thread). 10. Install the Step Plate. 11. Install the 2-Jaw Puller and loosen the rear hub to the point of removal. 12. hub bearing when b. Remove the rear hub assembly. 3. l a new hub seal ub assembly is removed. NOTE: The inner bearing is located behind the hub seal. Pack each bearing and replace the hub seals; for additional information, refer to Bearings, Cups and Seals in this section. 14. treme care not to scratch or gouge the seal or bearing surfaces. If after hub removal, the hub seal or seal inner sleeve remains on the spindle, remove it as shown using the Step Plate and the 2-Jaw Puller. 15. Inspect the seal surface and inner shoulder for scratches and damage. ? Remove all scratches, gouges or galling damage with #600 or finer crocus cloth. Installation 1. NOTE: Clean the spindle thoroughly after removing the rear hub. Coat the spindle with axle lubricant. 2. b bearings must be prelubed prior to installation. Fill the hub cavity with 29.6 ml (1 oz) of SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A. 3. treme care not to damage the hub g it to contact the spindle during installation. NOTE: Coat the spindle and hub seal inside diameter with SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL- M2C192-A. NOTE: Installing the rear hub in this manner causes the outer bearing to act as a pilot making the installation easier. Push the rear hub and outer bearing onto the spindle as an assembly. ? Hold the outer bearing seated and use the bearing as a pilot

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

2000 Ford Windstar Intake Manifold-Lower Removal And installation manual

download
Intake Manifold—Lower Removal 1. Partially drain the cooling system. For additional information, refer to Section 303-03 . 2. Remove the upper intake manifold (9424). For additional information, refer to Intake Manifold—Upper in this section. 3. Remove the fuel supply manifold (9F792). For additional information, refer to Section 303-04B . 4. Disconnect the EGR vacuum tube (9E498). 5. Disconnect the EGR-to-exhaust manifold tube (9D477). * Loosen the nut. 6. Disconnect the upper radiator hose (8260). * Reposition the clamp. * Disconnect the hose. 7. Disconnect the heater hose (18472). * Compress the fitting * Disconnect the hose. 8. Disconnect the intake manifold runner control (IMRC). 9. Position the water bypass tube (8555) aside. 1. Remove the bolts. 2. Position the tube aside. 10. NOTE: Note the location of the six long bolts. Remove the lower intake manifold (9J447). 1. Remove the bolts. 2. Remove the intake manifold. 11. Remove the intake manifold runner control (IMRC) if necessary. For additional information, refer to Section 303-14 . 12. Remove and discard the lower intake manifold sealing components. Installation 1. Refer to the illustration for intake manifold sealing component locations. 2. Install the lower intake manifold front and rear end seals. 1. Apply a bead of sealant to the intake manifold front and rear end seal mounting points as indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Install the lower intake manifold front and rear end seals. 3. Install the intake manifold gaskets (9439). 4. Install the intake manifold runner control (IMRC) if required. For additional information, refer to Section 303-14 . 5. NOTE: The lower intake manifold must be installed within four minutes of applying sealant. Position the lower intake manifold. 1. Apply a bead of sealant to the lower intake manifold mounting at the points indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Position the lower intake manifold.