Filed Under (Toyota Manuals) by admin on 26-10-2011
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.
, remove center peice from 2011 toyota camry
, toyota 4k carburetor manual download
, 2005 tundra grill removal
, how to check windshield wiper motor and arm on a 2007 malibut
, how replace alternator in 2006 honda odessey
, how remove intake plenum on 1998 Toyota sienna
, how to remove center console 2013 camry
, toyota sienna grill removal
, mercedes 1997 cell phone manual for sl500
Filed Under (Chevy Manuals) by admin on 14-05-2012
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.
Related Content:2013 f250xl radio removal
, 1998 dodge blower motors durango
, HOW TO REMOVE TOYOTA TACOMA FENDER LINER
, how to remove the heater core on 2000 VW Beetle
, Redezvous Dash Removal
, 2003 mitsubishi eclipse replace evapulator
, 2002 silverado remove front driveshaft
, 2002 ford taurus evap emission line location
, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette
, 2004 Buick lesabre inrument cluster removeal
Filed Under (Toyota Manuals) by admin on 16-03-2012
Removal 1) Disconnect negative battery cable. Remove battery, battery tray, air cleaner assembly and air cleaner case. Disconnect throttle valve cable from throttle body. Remove cruise control actuator with mounting bracket from body. 2) Raise and support vehicle. Disconnect necessary electrical connectors and ground cables for transaxle removal. Disconnect shift cable and oil cooler lines at transaxle. Remove shift cable clamp bracket from transaxle. 3) Remove front (radiator side) engine mount shock absorber- to-lower frame assembly bolts. Remove front (radiator side) engine mount-to-lower frame assembly bolts/nuts. Remove starter. 4) Remove front (radiator side) exhaust manifold brace from rear of exhaust manifolds. Brace fits between rear of exhaust manifold and front of transaxle. 5) Remove 4 upper transaxle-to-cylinder block bolts. Support engine with hoist. Steering gear assembly must be supported in place during transaxle removal. Secure steering gear assembly to engine hoist using an attaching strap placed at each end of steering gear assembly. 6) Remove front wheels. Remove front exhaust pipe located between exhaust manifolds and rear exhaust pipe. Drain transaxle fluid. Remove axle shafts from transaxle. See appropriate AXLE SHAFTS article in AXLE SHAFTS & TRANSFER CASES section. 7) Disconnect shift control cable from mounting bracket. Remove rear (firewall side) engine mount-to-lower frame assembly bolts/nuts. Remove transaxle mount-to-transaxle bolts at driver’s side end of transaxle. 8) Remove stabilizer bar mount bracket-to-lower frame assembly bolts. Remove steering gear assembly-to-lower frame assembly bolts/nuts. Support lower frame assembly with floor jack. Lower frame assembly is located below engine and transaxle. 9) Disconnect power steering reservoir pipe mounting brackets from lower frame assembly. Remove bolts for each fender liner from lower frame assembly. Remove lower frame assembly mounting brackets. Lower frame assembly mounting brackets are located on front and rear of lower frame assembly and attach lower frame assembly to body. Remove lower frame assembly. 10) Support transaxle with transmission jack. Remove torque converter cover from front of transaxle. Remove torque converter bolts. Remove remaining exhaust manifold support brace. Remove remaining transaxle-to-cylinder block bolts. Lower transaxle from vehicle.
Related Content:1972 chevelle assembly manual
, 70 Chevelle Horn Assembly diagram
, exploded view air intake assembly 2006 honda accord
, 70 Chevelle Horn Assembly Schematic
, how to replace fog light assembly on 2012 toyota seinna
, hunter l401 parts list
, Sienna 2012 fog light assebly removal and replacement
, replacing transaxles on 2006 chevy impala
, Sienna 2012 fog light assembly removal and replacement directions
, subaru transaxle bearing
Filed Under (Nissan Manuals) by admin on 24-02-2011
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables. 2. Remove front exhaust tube. Remove intake manifold collector supports, and intake manifold. Remove exhaust manifold with catalytic converter. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. Remove injectors and fuel rail as an assembly. Remove distributor cap and spark plugs. 3. Set cylinder No. 1 at TDC of compression stroke, ensuring marks on crankshaft pulley and front cover align, and distributor rotor points to spark plug wire No. 1 on cap. Remove cylinder head cover. Remove distributor. 4. Prevent camshafts from turning, and remove camshaft sprocket bolts. Remove camshaft sprocket. See Fig. 13 . Mark and remove camshaft bearing caps in reverse order of installation. See Fig. 16 . Remove camshafts. 5. Loosen cylinder head bolts in 2 or 3 steps, in reverse order of tightening sequence. See Fig. 11 . Remove camshaft sprocket cover. Remove outer (upper) chain tensioner and guide. Remove outer timing chain. Remove idler sprocket bolt. Remove cylinder head. 6. Remove oil pan and oil strainer. See OIL PAN. Remove accessory drive belts. Remove A/C compressor idler pulley (if equipped). Remove crankshaft pulley. Remove front cover. Remove chain tensioner, tensioner arm and chain guides. Remove inner (lower) timing chain and idler sprocket. Remove oil pump drive spacer and crankshaft sprocket. Inspection 1. Inspect chain roller links. Replace chain if roller links are cracked or worn. Inspect cylinder head and cylinder block mating surfaces for warpage. If warpage exceeds specification, machine cylinder head. See CYLINDER HEAD under ENGINE SPECIFICATIONS. 2. If machining reduces cylinder head height to less than specification, replace cylinder head. After machining, rotate camshaft by hand. Replace cylinder head if camshaft does not rotate freely.
Related Content:cummins n14 cylinder heads
, 2001 ford f 150 head removal
, how to disable child licks on 2013 GMC terrain
, how to replace cilinder head in1 8 toyota
, how to top overhaul peugeot 206
, is timing set on compresson stroke 2000 2 0 vw beetle
, procedure on removal fo cv axle in 2005 volvo s40 2 4i
, removing ih1066 cylinder liners
, slk230 head removal
, toyota head removal v6
Filed Under (Ford Manuals) by admin on 25-06-2012
Intake Manifold—Lower Removal 1. Partially drain the cooling system. For additional information, refer to Section 303-03 . 2. Remove the upper intake manifold (9424). For additional information, refer to Intake Manifold—Upper in this section. 3. Remove the fuel supply manifold (9F792). For additional information, refer to Section 303-04B . 4. Disconnect the EGR vacuum tube (9E498). 5. Disconnect the EGR-to-exhaust manifold tube (9D477). * Loosen the nut. 6. Disconnect the upper radiator hose (8260). * Reposition the clamp. * Disconnect the hose. 7. Disconnect the heater hose (18472). * Compress the fitting * Disconnect the hose. 8. Disconnect the intake manifold runner control (IMRC). 9. Position the water bypass tube (8555) aside. 1. Remove the bolts. 2. Position the tube aside. 10. NOTE: Note the location of the six long bolts. Remove the lower intake manifold (9J447). 1. Remove the bolts. 2. Remove the intake manifold. 11. Remove the intake manifold runner control (IMRC) if necessary. For additional information, refer to Section 303-14 . 12. Remove and discard the lower intake manifold sealing components. Installation 1. Refer to the illustration for intake manifold sealing component locations. 2. Install the lower intake manifold front and rear end seals. 1. Apply a bead of sealant to the intake manifold front and rear end seal mounting points as indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Install the lower intake manifold front and rear end seals. 3. Install the intake manifold gaskets (9439). 4. Install the intake manifold runner control (IMRC) if required. For additional information, refer to Section 303-14 . 5. NOTE: The lower intake manifold must be installed within four minutes of applying sealant. Position the lower intake manifold. 1. Apply a bead of sealant to the lower intake manifold mounting at the points indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Position the lower intake manifold.
Related Content:s10 2 2 upper intake manifold removal
, 2000 bmw528i how to remowe intake manifold
, 1997 FORD 4 2 INTAKE MANIFOLD RUNNER CONTROL VALVE DIAGRAM
, how remove intake manifold on 1998 Toyota sienna
, picture of bolt pattern of intake manifold on 2006 h3 hummer
, torque specs 02 grand prix intake bolt
, removing lower intake manifold 1994 pontiac grand prix
, manifold replacement on 5 7 volvo penta on you tube
, intake manifold torque on a 1999 bmw 528i
, locate intake manifold runner control vacuum hose for 2005 ford focus
Filed Under (Ford Manuals) by admin on 09-05-2012
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.
Related Content:2000 mpv egr vacuum line
, 1997 FORD EXPLORER VACUUM T SHAPPED HOSE
, 2az fe intake manifold
, 305 egr intke gasket
, bad egr valve symptoms aveo chevrolet
Filed Under (Lincoln Manuals) by admin on 27-02-2011
Intake Manifold — Upper Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the engine appearance cover. 4. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 5. Disconnect the throttle position (TP) sensor and the idle air control (IAC) solenoid electrical connectors. 6. Disconnect the accelerator and speed control cables. 7. Remove the cable bracket. 1. Remove the bolts. 2. Remove the bracket. 8. Disconnect the throttle body hoses. 1. Disconnect the coolant hoses. 2. Disconnect the positive crankcase ventilation (PCV) hose. 3. Disconnect the vapor purge hose. 9. Disconnect the vacuum hose. 10. Disconnect the EGR to exhaust manifold tube nut. 11. Remove the cowl vent screen. For additional information, refer to Section 501-02 . 12. Remove the brace. 13. Remove the vacuum hoses from the mounting bracket. 14. Remove the bracket and position the accelerator and cruise control cables aside. 15. Disconnect the differential pressure feedback EGR electrical connector. 16. Remove the stud and nut and position the differential pressure feedback EGR transducer aside. 7. Remove the fuel pressure sensor shield. 1. Remove the nut. 2. Remove the bolts. 3. Remove the shield. 18. Disconnect the vacuum hose from the rear of the upper intake manifold. 19. Disconnect the intake manifold tuning valve (IMTV) electrical connector. 20. Disconnect the exhaust vacuum regulator (EVR). 1. Disconnect the electrical connector. 2. Disconnect the vacuum line. 21. Remove the upper intake support bolt. 22. Remove the front intake manifold support bolt.
Filed Under (Chevrolet Manuals) by admin on 30-04-2012
Intake Manifold Replacement (Lower) Notes Intake Manifold Replacement – Lower Removal Procedure 1. Disconnect the negative bakery. 2. Remove the upper intake manifold. 3. Remove the left valve rocker arm cover. 4. Remove the right valve rocker arm cover. 5. Disconnect the Engine Coolant Temperature ( ECT ) sensor electrical connector. 6. Disconnect and remove the fuel injector and the Manifold Absolute Pressure (MAP) sensor wiring harnesses. 7. Remove the fuel pipe clip bolt. 8. Remove the fuel pipe clip. 9. Remove the fuel feed pipe from the fuel injector rail. 10. Remove the fuel return pipe from the fuel injector rail. 11. Remove the fuel injector rail. 12. Remove the power steering pump from the front engine cover and reposition. 13. Remove the heater inlet pipe with heater hose from the lower intake manifold and reposition. 14. Remove the radiator inlet hose from the engine. 16. Remove the lower intake manifold bolts. 17. Remove the lower intake manifold. 18. Remove the valve rocker arms and pushrods. 19. Remove the lower intake manifold gaskets and seals. 20. Clean the lower intake manifold gasket mating surfaces. 21. Remove and clean all the RTV sealant from the lower intake manifold and the engine block (1).
Filed Under (Toyota Manuals) by admin on 04-04-2012
REMOVAL AND INSTALLATION OF TRANSMISSION Removal of Transmission REMOVE NEGATIVE BATTERY CABLE CAUTION: Work must be started after approx. 20 se- conds or longer from the “LOCK” position and the nega- tive (-) terminal cable is disconnected from the battery. REMOVE CENTER CLUSTER FINISH PANEL REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE RAISE VEHICLE AND DRAIN TRANSMISSION OIL NOTICE: Be sure the vehicle is securely supported. REMOVE PROPELLER SHAFT Remove the propeller shaft and insert SST into the extension housing. SST 09325-2001 0 (for W58 M/T) 09325-4001 0 (for R 1 54 MIT) DISCONNECT EXHAUST FRONT PlPE FROM TAIL PlPE (a) Remove the rubber hanger. (b) Disconnect the pipe at the front side of the converter. (R154 M/T) REMOVE EXHAUST FRONT PlPE (a) Disconnect the exhaust pipe bracket from the clutch housing. (b) Remove the nuts and exhaust pipe from the exhaust manifold. DISCONNECT SPEEDOMETER CABLE DISCONNECT BACK-UP LIGHT SWITCH CONNECTOR AND REAR SPEED SENSOR CONNECTOR (wl A.B.S.) MANUAL TRANSMISSION – Removal and Installation of Transmission MT-5 10. REMOVE CLUTCH RELEASE CYLINDER 11. REMOVE STARTER Remove the mounting bolts and lay the starter alongside the engine. 12. JACK UP TRANSMISSION SLIGHTLY Raise the transmission enough to remove the weight from the rear support. 13. REMOVE ENGINE REAR MOUNTING 14. REMOVE TRANSMISSION MOUNTING BOLTS AND FLYWHEEL HOUSING UNDER COVER 15.-1 (W58 M/T) REMOVE TRANSMISSION ASSEMBLY Pull out the transmission down and toward the rear. 15.-2 (R154 M/T) REMOVE TRANSMISSION ASSEMBLY WITH CLUTCH COVER AND DISC (a) Remove the two clutch housing covers. (b) Pull out the release fork through the left clutch housing hole. (c) Place the matchmarks on the clutch cover and flywheel. (d) Remove the clutch cover set bolts while turning the crankshaft pulley. HINT: Loosen each set bolt one turn at a time until spring tension is released. (e) Remove the clutch cover and disc from the flywheel, and fully move them toward the transmission. (f) Pull out the transmission with the clutch cover and disc.
Filed Under (Toyota Manuals) by admin on 20-06-2011
Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level. 3 AVALON 2005- 2010 2GR-FE PU140-00900 PU140- 03571 Rear, L.H.S. (hole direction pointing to front) Route cord up. Tie the cord to the lower heater hose outlet. Route the cord to left side of engine. Tie the cord to the main harness besides the fuse box. Remove front radiator plastic cover. Route the cord down on left side of battery and tie the cord to the left side of radiator coolant fan harness at the front bottom of the battery. Route the cord to the front and tie to the front grille. 11 1983- 86 2SE C0140-00123* C0140- 00069 Front L.H.S. 2nd from transmission 6 1987- 91 3S-FE C0140-00134* C0140- 00070 Rear 2nd from right 12 1988- 91 2V-ZFE C0140-00110* C0140- 00767 Front centre. Loosen union bolt of water outlet five revolutions before refilling coolant. Tighten after coolant fill. 12 1992- 93 3VZ-FE C0140-01141* C0140- 00903 Front 1st from left. Remove exhaust manifold; remove exhaust pipe if necessary. Route cordset towards the left side of engine compartment. 6 1992- 2001 5S-FE C0140-01123* C0140- 02899 Front, 2nd from left. Remove exhaust manifold. For models prior to 1994 model year, remove upper exhaust manifold heat shield only. Route cordset towards left side of engine compartment. 12 CAMRY 1994- 2006 IMZ-FE C0140-00644* C0140- 02897 Front, R.H.S. Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level
Related Content:2008 camry how to eemove enine
, 2gr-fe manual