Skip to content

remove mazda 626 center console

You search PDF repair manual about remove mazda 626 center console, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Honda Accord LX CENTER CONSOLE REMOVAL/ INSTALLATION MANUAL

download
CONSOLES CENTER CONSOLE REMOVAL/INSTALLATION 1. M/T model: Remove the shift knob (A). a. Lower the shift lever boot (B) to release the hook (C) from the knob. b. Remove the shift knob. Fig. 34: Removing The Shift Knob 2. Detach the clips (A, B) by pulling the center console front panel (C) up, If equipped, disconnect the seat heater switch connectors (D). Fig. 35: Detaching The Clips 3. Pry up on the left of the console pocket (A) with a flat-tip screwdriver wrapped with a shop towel, and detach the clips, then remove the pocket. Fig. 36: Removing The Pocket 4. Remove the screws (A), detach the clips (B) and hook (C) by pulling the center holder (D) up, and disconnect the front accessory power socket connector (E) Fig. 37: Disconnecting The Front Accessory Power Socket Connector 5. Detach the clips (A, B) by pulling the center console rear panel (C) up Fig. 38: Detaching The Clips 6. Remove the center console (A). a. Open the console box lid (B) then remove the console mat (C). b. If equipped, disconnect the rear accessory power socket connector (D), and detach the clip (E). c. Remove the screws (F, G), then pull the rear portion of the console up to release the hooks (H), then remove it.

1998 Mercedes Benz SLK 230 Removing And Installing Rear Center Console

download
1998 Mercedes Benz SLK 230 (170.447) L4-2.3L SC (111.973) Vehicle Level Body and Frame Interior Moulding / Trim Console Service and Repair AR68.20-P-2410G Remove/Install Ashtray Housing With Stowage Compartment In Front Center Console AR68.20-P-2410G Remove/Install Ashtray Housing With Stowage Compartment In Front Center Console Notes Remove/Install Ashtray Housing With Stowage Compartment In Front Center Console AR68.20-P-2020G Remove/Install Rear Center Console Notes Removing And Installing Rear Center Console

1983 Mazda RX-7 GSL ENGINE COMPRESSION TESTING

download
HIGH TENSION WIRE RESISTANCE Carefully remove high tension wires from spark plugs and distributor cap. Using an ohmmeter, measure resistance of wires while gently twisting wires. If resistance is not to specifications, or fluctuates from infinity to any value, replace high tension wire(s). HIGH TENSION WIRE RESISTANCE High Tension Wire Routing For high tension wire routing, see Fig. 2 and Fig. 3 . Fig. 3: Locating High Tension Wires On Distributor Cap Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS DISTRIBUTOR All models are equipped with Mitsubishi electronic ignition with 2 pick-up coils. Air gap is non-adjustable IGNITION TIMING 1. Warm engine to normal operating temperature. Connect a tachometer, then connect timing light to leading (lower) spark plug of front rotor. Start engine and run at idle speed. 2. Check ignition timing and rotate distributor to correct if necessary. Tighten distributor lock nut and recheck timing. 3. Connect timing light to trailing (upper) plug of front rotor. Start engine and check timing. If not correct, loosen vacuum unit attaching screws. Move vacuum unit in or out to adjust trailing timing. Remove test equipment.

1998 Mazda Truck MPV ES 2WD Accessories and Optional Equipment Radio, Stereo, and Compact Disc Service and Repair Manual

download
REMOVAL 1. Disconnect the negative battery cable. 2. Remove the hole covers by inserting a small, tape-wrapped, flathead screwdriver into the slot and carefully prying them off without scratching the center lower panel. Pry up and pull off the hole covers carefully to prevent the posts from breaking off. 3. With the beveled parts of the SST facing inward, insert them into the audio unit. 4. Pull the SST as shown to slide out the audio unit. 5. Disconnect the audio unit connector and antenna jack to remove the audio unit. INSTALLATION CAUTION: * Make certain that the wiring harness and antenna feeder are not caught between the audio unit and center lower panel. If the harness or antenna feeder is caught between the audio unit and center lower panel, it may become the cause of trouble or malfunctions. 1. Connect the audio unit connector and antenna jack. 2. Insert the audio unit until each clip clicks. 3. Insert the hole covers. 4. Connect the negative battery cable.

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.