Skip to content

remove radio from pontiac g5

You search PDF repair manual about remove radio from pontiac g5, if there are search results will appear below. If search results do not exist, please search by others keyword.

2001 Toyota Highlander Sport Utility, Radio, FRONT DOOR SPEAKER INSTALLATION MANUAL

download
2001 Toyota Highlander Sport Utility PRELIMINARY: Disconnect the negative battery cable. ANTENNA: The factory antenna is located atop the right front fender panel. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a Double ISO/DIN style radio. An installation kit is required when installing an aftermarket stereo. 1. Using panel removal tool carefully pry off radio bezel. 2. Extract (6) 10 mm bolts securing radio and climate controls in dash, disconnect and remove. 3. Extract (8) Iso screws securing radio to bracket. 4. Extract (2) Philips screws securing bracket to bezel, pull away and remove radio. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ½” tweeter and a 6 ½” 3-Hole speaker mounted to a factory speaker adapter. 1. Remove screw cover from door opener cup and exract (1) Philips head screw, pry bezel out then forward to remove. 2. Remove inside mirror cover. 3. Pry out door cup and extract (1) Philips screw from beneath. 4. Exract (1) plastic fastener from front top portion of door. 5. Pry off door panel, pull away, disconnect, and remove. 6. Extract (3) 10 mm bolts securing speaker, pull away, disconnect, and remove. REAR DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 5 ¼” 3-Hole speaker mounted in a factory speaker adapter. 1. Remove screw cover from door opener cup and extract (1) Philips head screw, pry bezel out then forward to remove. 2. Pry out door cup and extract (1) Philips screw from beneath. 3. Pry off door panel, pull away, disconnect and remove. 4. Extract (3) 10 mm bolts securing speaker , pull away, disconnect, and remove

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

2009 HONDA ODYSSEY XM SATELLITE RADIO SYSTEM INSTALLATION INSTRUCTIONS

download
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Open the sunglass holder, and remove the two 5 mm bolts. Insert a flat-tip screwdriver between the lens and roof console housing, and gently pry out the map light lens covers. Remove the two ground bolts. Pull out the roof console from the headliner. 4. Disconnect the two vehicle connectors and remove the roof console. 4713010B VEHICLE CONNECTORS ROOF CONSOLE LEFT MAP LIGHT LENS COVER 2 GROUND BOLTS 4 RETAINING TABS 4 RETAINING TABS RIGHT MAP LIGHT LENS COVER SUNGLASS HOLDER 2 BOLTS, 5 x 8 mm HEADLINER ANTENNA BUS CABLE XM TUNER ANTENNA CABLE 6402010B

2007 HONDA RIDGELINE XM RADIO SYSTEM INSTALLATION INSTRUCTIONS

download
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. ull away the weatherstrip from around passenger’s A-pillar. Remove the passenger’s A- pillar trim (two clips). Illustration of the XM Radio Installed on the Vehicle Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

2009 CIVIC 2-AND 4-DOOR (EX, EX-L) XM RADIO SYSTEM INSTALLATION INSTRUCTIONS

download
INSTALLATION 1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the audio presets. 2. Disconnect the negative cable from the battery. 3. Remove the passenger’s dashboard under cover (four clips and two pins). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 871104AH PASSENGER’S DASHBOARD UNDER COVER 4 CLIPS 2 PINS 4. Remove the two bolts under the glove box. 5. Open and remove the glove box (two stoppers). 6. Remove the driver’s dashboard lower cover (eight clips)