remove skid plate from 2007 tundra

You search PDF repair manual about remove skid plate from 2007 tundra, if there are search results will appear below. If search results do not exist, please search by others keyword.



  remove skid plate from 2007 tundra Direct Download speed 5432 Kb/s

  remove skid plate from 2007 tundra Full Version speed 8172 Kb/s



2007-2009 TOYOTA TUNDRA 2WD AND 4WD 6″ SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 11-11-2011

download
Front Installation Instructions 1. Raise the vehicle. If working without a shop hoist, support vehicle with suitable safety jack stands. Put vehicle in gear, set emergency brake and block rear wheels, both in front and behind tires. Loosen front wheel lug nuts. Place floor jack under the lower control arm’s front crossmember and raise vehicle. Place safety jack stands under frame rails, behind front wheel wells, and lower the frame onto the stands. Once securely on jack, stands remove floor jack. Remove front wheels. 2. Remove the skid plate and skid plate brackets. (Illustration 1) 3. Beginning with the drivers side, unclip the ABS sensor line and disconnect at the knuckle. Remove the screw attaching the brakeline to the knuckle. (Illustration 2) 4. Remove the bolts holding the Caliper Anchor Bracket to the Steering Knuckle (Illustration 2). Pull the Bracket and Caliper assembly away from the Brake Rotor and hang out of the way with a length of wire, careful not to damage the brake lines. DO NOT let the Caliper hang from the brake line. 5. Remove the Brake Rotor from the Hub and set aside. (Illustration 2) 6. Remove Axle Hub Dust Cap. (Illustration 2) 7. Remove the axle to wheel hub nut. (Illustration 2) 8. Disconnect and remove Sway Bar with Links from vehicle. (Illustration 3) 9. Remove the nut from the steering Tie Rod. Separate the Tie Rod from the Steering Knuckle. (Illustration 2) 10.Remove the nut from the Upper Ball Joint. Separate the Upper Ball Joint from the Steering Knuckle. (Illustration 2) 11.Remove the two bolts attaching the Knuckle to Lower Ball Joint Bracket. (Illustration 4) 12.Remove Steering Knuckle and set aside. 13.Disconnect Front Strut from Lower Control Arm at bottom, and from Frame at top, and remove. (Illustration 5) 14.Remove the lower control arm pivot bolts and remove lower control arm.

Related Content:

2007 toyota tundra rotor removal, How to remove brake rotor 2010 tundra

2007 & NEWER TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 01-04-2012

download
The mounting procedure outlined below covers the 2007 and Newer Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the frame and the rear cross member. Remove the skid plate. Do not discard the skid plate or bolts so that they can be reinstalled if the undercarriage is removed. 2. Remove the two bolts from both tow hooks. Remove both tow hooks. Retain the bolts as they will be reinstalled further into the installation procedure. Do not discard the tow hooks so that they can be reinstalled if the undercarriage is removed. 3. Remove the three bumper mount nuts located on the front end of the driver side frame rail. Retain the nuts as they will be reinstalled further into the installation procedure. 4. Place Driver Side Push Beam Support Plate (62B) against the bottom of the driver side truck tow hook mount and against the outside of the driver side frame rail. The front tab of Push Beam Support Plate (62B) must clear the bumper mount studs on the front end of the truck frame. 5. Slide Driver Side Push Beam Support Plate (62B) backward until the three bumper mount studs on the end of the truck frame fully engage the three holes located on Driver Side Push Beam Support Plate (62B). 6. Reinstall the three bumper mount nuts that were removed in step 3. Fasteners should only be finger tight. 7. Assemble Driver Side Push Beam Support Plate (62B) to the tow hook mount using the two bolts removed in step 2. Fasteners should only be finger tight. 3 8. Using Bolt Puller (102) insert one ½” X 1-½” Hex Head Bolt (A) through the hole located on the outside of the driver side frame rail and through the hole located in Driver Side Push Beam Support Plate (62B). Secure with one ½” Split Lock Washer (D) and one ½” Hex Head Full Nut (C). Fasteners should only be finger tight. 9. Tighten the truck tow hook bolts. The heads of these bolts will not be accessible once Push Beam (62) is installed. 10. Repeat steps 3-9 for Passenger Side Push Beam Support Plate (62A). 11. Slide three Nut Plates (101) through the truck cross member. Align Nut Plates (101) with the front side of the two large outside holes and large center hole. 12. Place Angle Bracket (75) against the bottom of the truck cross member. Secure with three ½” X 1-½” Hex Head Bolts (A) and three ½” Split Lock Washers (D) and Nut Plates (101) previously installed inside the truck cross member. Fasteners should only be finger tight. 13. Install Push Beam (62) between Passenger Side and Driver Side Push Beam Support Plates (62A & 62B) using eight ½” X 1-½” Hex Head Bolts (A) and eight ½” Nylon Lock Nuts (B). Push Beam (62) should be mounted at a height of 14-½” from the ground to the center of the hook hole. Fasteners should only be finger tight. 14. Assemble Angle Bracket (75) to Push Beam (62) using four ½” X 1-½” Hex Head Bolts (A) and four ½” Nylon Lock Nuts (B). Fasteners should only be finger tight. 15. Tighten all fasteners, starting with Angle Bracket (75) and continuing forward. 16. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

Related Content:

2007 sorento center bearing, how to install a pushnut

Related Content:

2007 toyota tundra rotor removal, How to remove brake rotor 2010 tundra