remove timing chain cover 96 altima

You search PDF repair manual about remove timing chain cover 96 altima, if there are search results will appear below. If search results do not exist, please search by others keyword.



  remove timing chain cover 96 altima Direct Download speed 5432 Kb/s

  remove timing chain cover 96 altima Full Version speed 8172 Kb/s



TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 09-06-2012

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

Related Content:

toyota tacoma 2000 REMOVE COMPRESSOR DRIVE BELT, 2002 ford ranger 2 3L timing tool, 2002 nissan altima changing camshafts, 2002 toyota tundra manual, Centurial Timing Module

1996 Nissan Altima GLE TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Nissan Manuals) by admin on 24-02-2011

download
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables. 2. Remove front exhaust tube. Remove intake manifold collector supports, and intake manifold. Remove exhaust manifold with catalytic converter. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. Remove injectors and fuel rail as an assembly. Remove distributor cap and spark plugs. 3. Set cylinder No. 1 at TDC of compression stroke, ensuring marks on crankshaft pulley and front cover align, and distributor rotor points to spark plug wire No. 1 on cap. Remove cylinder head cover. Remove distributor. 4. Prevent camshafts from turning, and remove camshaft sprocket bolts. Remove camshaft sprocket. See Fig. 13 . Mark and remove camshaft bearing caps in reverse order of installation. See Fig. 16 . Remove camshafts. 5. Loosen cylinder head bolts in 2 or 3 steps, in reverse order of tightening sequence. See Fig. 11 . Remove camshaft sprocket cover. Remove outer (upper) chain tensioner and guide. Remove outer timing chain. Remove idler sprocket bolt. Remove cylinder head. 6. Remove oil pan and oil strainer. See OIL PAN. Remove accessory drive belts. Remove A/C compressor idler pulley (if equipped). Remove crankshaft pulley. Remove front cover. Remove chain tensioner, tensioner arm and chain guides. Remove inner (lower) timing chain and idler sprocket. Remove oil pump drive spacer and crankshaft sprocket. Inspection 1. Inspect chain roller links. Replace chain if roller links are cracked or worn. Inspect cylinder head and cylinder block mating surfaces for warpage. If warpage exceeds specification, machine cylinder head. See CYLINDER HEAD under ENGINE SPECIFICATIONS. 2. If machining reduces cylinder head height to less than specification, replace cylinder head. After machining, rotate camshaft by hand. Replace cylinder head if camshaft does not rotate freely.

Related Content:

1997 altima cam timing, cummins n14 cylinder heads, 03 2az-fe head dowel pins, how to disable child licks on 2013 GMC terrain, how to install cylinder head on c-15cat engine, how to replace cilinder head in1 8 toyota, how to top overhaul peugeot 206, is timing set on compresson stroke 2000 2 0 vw beetle, procedure on removal fo cv axle in 2005 volvo s40 2 4i, removing ih1066 cylinder liners

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 10-05-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

Related Content:

1997 saturn manifold repair, 2000 lexus es 300 gear sprocket, 2007 SATURN RELAY 3 9 V6 TIMING CHAIN/ MAGNETIC SPROCKET

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, timing mark on hino, 98 eclipse rs service manual, 2002 diamante timing belt, 2002 jetta crank mark, 2003 eclipsed2 4 litre cranckshaft position sensor location, 91 honda accord timing belt marks diagram, should the timing arrow on a zx2 move when belt is pressed

1994 Toyota Camry DX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 22-01-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution. 7. Loosen No. 1 idler pulley bolt. See Fig. 1 . Move No. 1 idler pulley outward, away from timing belt as far as possible. Temporarily retighten No. 1 idler pulley bolt. Remove timing belt from camshaft sprocket. 8. Using Pulley Holder (SST 09213-54015) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. 9. Using gear puller, remove crankshaft pulley. Remove No. 1 timing belt cover and gasket. Note direction of timing belt guide installation. See Fig. 1 . Remove timing belt guide. 10. Loosen No. 1 idler pulley bolt. See Fig. 1 . Remove timing belt from crankshaft sprocket. Remove idler pulleys (if necessary).

Related Content:

96 Toyota Camry 3 0 Timing Marks, TOYOTA 4Y TIMING MARKS, toyota 7A-FE timing belt alignment marks, Toyota Camry Crankshaft Pulley Removal

2000 Dodge Intrepid Timing Chain Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 21-11-2011

download
REMOVAL 1.Remove upper intake manifold. 2.Remove cylinder head covers, crankshaft damper, and timing chain cover. CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. Fig. 70 3.Align crankshaft sprocket timing mark to mark on oil pump housing (Fig. 70). The mark on oil pump housing is 60° ATDC of #1 cylinder. CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage Fig. 74 4.Remove primary timing chain tensioner from right cylinder head (Fig. 74). 5.Remove camshaft position sensor from left cylinder head (Fig. 69). 6.Remove chain guide access plug from left cylinder head (Fig. 69). NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction. 7.Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper and sprocket (Fig. 69). 8.Remove left side camshaft sprocket attaching bolts and remove sprocket (Fig. 69). 9.Remove lower chain guide and tensioner arm (Fig. 69). 10.Remove the primary timing chain. INSTALLATION 1.Inspect all sprockets and chain guides. Replace if worn. Refer to Crankshaft Gear/Sprocket, for removal and installation procedures. 2.If removed, install right and left side short chain guides (Fig. 69). Tighten attaching bolts to 28 Nm (250 in. lbs.) 3.Align crankshaft sprocket timing mark to the mark on oil pump housing (Fig. 71). NOTE: Lubricate timing chain and guides with engine oil before installation. 4.Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (Fig. 71). 5.Lower the primary chain with left side sprocket through the left cylinder head opening

Related Content:

2006 trailblazer timing marks, diagram of a 00 lincoln ls 3 9 liter timing chain and gears, 2004 pontiac sunfire timing chain replacement, 04 ford escape timing chain settings, tdc on jaguar 4 0, sport trac timing chain replacement interval, number one cylinder cam is not near 11 o\clock why? 04 nissan quest, is crankshaft position sensor removed when replacign timing chain on 2001 durango, installing timing chain on 2000 dodge ram 1500, how to replace the timing chain on a 2004 maxima 3 5

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, how to remove center console 2013 camry, how remove intake plenum on 1998 Toyota sienna, how replace alternator in 2006 honda odessey, toyota sienna grill removal, jaguar fuel hose removal, 4k carburetor manual, toyota 4k carburetor service manual

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture