Skip to content

removing door panel mazda mpv

You search PDF repair manual about removing door panel mazda mpv, if there are search results will appear below. If search results do not exist, please search by others keyword.

2006 Honda CR-V EX FRONT DOOR PANEL REMOVAL/ INSTALLATION MANUAL

download
FRONT DOOR PANEL REMOVAL/INSTALLATION Special Tools Required * Trim pad remover, Snap-on A 177A or equivalent, commercially available * KTC trim tool set SOJATP2014 1. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover. 2. Remove the screws. 3. Driver’s door: Pull the inner handle (A) rearward and out half-way to release the power door lock switch bracket (B) from the door panel (C). Fig. 7: Pulling Inner Handle – Driver Door Courtesy of AMERICAN HONDA MOTOR CO., INC. 4. Passenger’s door: Pull the inner handle (A) halfway. Fig. 8: Pulling Inner Handle – Passenger Door Courtesy of AMERICAN HONDA MOTOR CO., INC. 5. Driver’s door: Disconnect the power door lock switch connector (A). Disconnect the inner handle rod (B), then remove the inner handle (C). Fig. 9: Disconnecting Power Door Lock Switch Connector – Driver Door Courtesy of AMERICAN HONDA MOTOR CO., INC. 6. Lower the glass fully. 7. Remove the screws from under the armrest. Fig. 10: Removing Screws From Under Armrest Courtesy of AMERICAN HONDA MOTOR CO., INC. 8. Passenger’s door: Remove the switch panel (A). * 1 Insert a flat-tip screwdriver wrapped with protective tape through a hole under the armrest, and push up the back of the panel to release the rear hook (B). * 2 Pull out along the edge of the panel to release the hooks (C) and clip. * 3 Disconnect the power window switch connector (D). Fig. 11: Disconnecting Power Window Switch Connector Courtesy of AMERICAN HONDA MOTOR CO., INC. 9. Remove the mirror mount cover (see step 2 on POWER MIRROR REPLACEMENT ). 10. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it. * 1 Release the clip (B). * 2 Release the clips (C) that hold the door panel with a commercially available trim pad remover (D).

1996-2000 Honda Civic Door Panel REMOVAL And INSTALLATION Manual

download
Honda Door Panel 96-00 Civic REMOVAL & INSTALLATION Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure. Honda Civic/Del Sol 1996-2000 Electric Window Motor REMOVAL & INSTALLATION 1. Remove the regulator from the door assembly. 2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7/ 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized. 3. Drill out the ends of the motor attaching rivets using a 1/ 4 in. (6mm) bit. 4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly. Regulator and motor assembly—except rear doors Secure the rivets by collapsing the rivet ends using a ball peen hammer To install: 5. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer. 6. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle’s window motor harness) to rotate the regulator, providing access to the remaining rivet. 7. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet. 8. Install the regulator to the door assembly.

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed

1994 Ford Town Car/ Crown Victoria/ Grand Marquis Trim Panels, Door Removal And Installation Manual

download
Trim Panels, Door Front Town Car The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification. Removal CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove. 1. Snap out two door pull strap retaining screw covers. Remove screws. 2. Remove two screws on front and rear side of front door trim panel. 3. Using the Trim Pad Removing Tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent, pry the trim panel retaining clips from the door inner panel. NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins. 4. Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors. 5. Disconnect driver seat regulator control processor switch (driver door only) if equipped. 6. Twist out interior lamp wire assembly and remove the front door trim panel. Installation 1. Ensure plastic watershield is secured to door panel. 2. Position front door trim panel to door. Connect interior lamp wiring. 3. Position the window regulator control switch housing and connect switch connectors. 4. Connect driver seat regulator control processor (14C708) (driver door only) if equipped. 5. Align door lock side to its mating slide on the sheet metal (front doors only) 6. Snap in front door trim panel . Ensure all retainers fit properly. 7. Install two retaining screws on front and rear side of front door trim panel . 8. Install two retaining screws and pull strap covers. Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup (22634) by gently prying at screwdriver slot with a screwdriver. 5. Remove push pin from front door trim panel upper front extension and remove screw. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. On Grand Marquis only, pry up screw covers from door pull handle and remove screws and handle. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel . Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. On Grand Marquis only, install door pull handle, tighten screws and install screw covers. 5. Install push pin covering screw on trim panel upper front extension. 6. Install inside door handle cup . 7. Install window regulator control switch housing.