Skip to content

removing oil filter adapter gasket on 2002 f150

You search PDF repair manual about removing oil filter adapter gasket on 2002 f150, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 Ford Excursion, F-Super Duty 250-550 Oil Filter Adapter Removal And Installation manual

download
Removal 1. Remove the LH engine mount. For additional 6. Disconnect the oil pressure switch electrical information, refer to Engine Mounts in this connector. section. 2. Drain the engine cooling system. For additional information, refer to Section 303-03. 3. Disconnect the coolant hoses. 7. Remove the oil pressure switch. 4. Remove the oil filter. 5. Remove the threaded insert and the oil cooler. 8. Disconnect the lower radiator hose. 2. Connect the lower radiator hose. 9. Remove the nut, the bolts, the oil filter adapter and the gasket. •Discard the gasket. 3. Install the oil pressure switch. 10. Clean the gasket surface at the cylinder block. Installation 1. Position the oil filter adapter gasket and the oil filter adapter. Install the nut and bolts. 4. Connect the oil pressure switch electrical connector. 7. Connect the coolant hoses. 5. NOTE: Make sure the tab on the oil filter adapter nests into the notch in the oil cooler. Position the oil cooler on the oil filter adapter and install the threaded insert. 8. Install the LH engine mount. For additional information, refer to Engine Mounts in this section. 9. Fill the engine with clean engine oil. 10. Fill and bleed the cooling system. For 6. Install a new oil filter. additional information, refer to Section 303-03

Ford Excursion Oil Filter Adapter Removal and Installation Manual

download
Removal 1. Remove the LH engine mount. For additional 6. Disconnect the oil pressure switch electrical information, refer to Engine Mounts in this connector. section. 2. Drain the engine cooling system. For additional information, refer to Section 303-03. 3. Disconnect the coolant hoses. 7. Remove the oil pressure switch. 4. Remove the oil filter. 5. Remove the threaded insert and the oil cooler 8. Disconnect the lower radiator hose. 2. Connect the lower radiator hose. 9. Remove the nut, the bolts, the oil filter adapter and the gasket. •Discard the gasket. 3. Install the oil pressure switch. 10. Clean the gasket surface at the cylinder block. Installation 1. Position the oil filter adapter gasket and the oil filter adapter. Install the nut and bolts IN-VEHICLE REPAIR (Continued) 4. Connect the oil pressure switch electrical connector. 7. Connect the coolant hoses. 5. NOTE: Make sure the tab on the oil filter adapter nests into the notch in the oil cooler. Position the oil cooler on the oil filter adapter and install the threaded insert. 8. Install the LH engine mount. For additional information, refer to Engine Mounts in this section. 9. Fill the engine with clean engine oil. 10. Fill and bleed the cooling system. For 6. Install a new oil filter. additional information, refer to Section 303-03

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.