repair buick park ave power windows

You search PDF repair manual about repair buick park ave power windows, if there are search results will appear below. If search results do not exist, please search by others keyword.



  repair buick park ave power windows Direct Download speed 5432 Kb/s

  repair buick park ave power windows Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, dodge durango 2002 suspension layout, free 1997 buick regal gs wiring diagrams, 2003 s10 airbag wiring diagram, 1998 Dodge Dakota Service Manual, zimmatic pivot wiring, abs and Anti Theft Passive 2000 mercury cougar, 2000 durango passenger power window switch diagram, Service manual dodge durano 2002 pdf

1991-1994 FORD TEMPO VEHICLE WIRING

0

Filed Under (Ford Manuals) by admin on 26-05-2012

download
WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 1992 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

1999 CHEVY SILVERADO DRIVER MIRROR MOTOR installation Instructions, 2008 chevy driver door switch wiring schmatic, 2003 pontiac vibe installing a 2 wire push button, 2002 lincoln town car driver side door expanted view, 1999 cadillac deville drivers seat diagram, 04 impala driver side window regulator diagram, how to repair wiring in drivers door on ford f150, how to remove glass from 1968 chevelle door, how to fix a 2011 kia drivers door handle, how to remove mdx drivers seat coushon

2000-2004 TOYOTA ECHO VEHICLE WIRING INFORMATION

0

Filed Under (Toyota Manuals) by admin on 21-05-2011

download
WIRING INFORMATION 2002 Toyota Echo WIRE WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE/RED and WHITE/BLUE Ignition Harness 12V IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness When installing a remote start, the second ignition wire (BLACK/RED) must be isolated from the key switch ACCESSORY WIRE WHITE/BLUE Ignition Harness STARTER WIRE BLACK Ignition Harness PARKING LIGHTS (+) GREEN At Headlight Switch POWER DOOR LOCK (-) BROWN/YELLOW Harness In Passenger’s Kick Panel POWER DOOR UNLOCK (-) GREEN/BLACK Harness In Passenger’s Kick Panel DOOR TRIGGER (-) RED/WHITE At Top Of Fuse Box TRUNK TRIGGER (-) RED/BLUE Harness In Driver’s Kick Panel FACTORY ALARM ARM Arms with lock FACTORY ALARM DISARM Disarms with unlock TACHOMETER BLACK At Diagnostic Plug Under Driver’s Side Of Dash BRAKE WIRE (+) GREEN/WHITE At Brake Pedal Switch HORN TRIGGER (-) WHITE/RED Harness At Steering Column LEFT FRONT WINDOW UP RED At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN GREEN At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN GREEN/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN GREEN/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION 2003 Toyota Echo WIRE WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE/RED and WHITE/BLUE Ignition Harness 12V IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness When installing a remote start, the second ignition wire (BLACK/RED) must be isolated from the key switch ACCESSORY WIRE WHITE/BLUE Ignition Harness STARTER WIRE BLACK Ignition Harness PARKING LIGHTS (+) GREEN At Headlight Switch POWER DOOR LOCK (-) BROWN/YELLOW Harness In Passenger’s Kick Panel POWER DOOR UNLOCK (-) GREEN/BLACK Harness In Passenger’s Kick Panel DOOR TRIGGER (-) RED/WHITE At Top Of Fuse Box TRUNK TRIGGER (-) RED/BLUE Harness In Driver’s Kick Panel FACTORY ALARM ARM Arms with lock FACTORY ALARM DISARM Disarms with unlock TACHOMETER BLACK At Diagnostic Plug Under Driver’s Side Of Dash BRAKE WIRE (+) GREEN/WHITE At Brake Pedal Switch HORN TRIGGER (-) WHITE/RED Harness At Steering Column LEFT FRONT WINDOW UP RED At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN GREEN At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN GREEN/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN GREEN/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

2004 chevy traiblazer drivers side front axle seal, 08 silverado driver door wire harnes, wanted driverside wire harnes for 2008 pontiac torrent, the cable under the front light of the car is detached, Differential Seal for 2004 Trailblazer, Mazda 2012 Ignition Lock Cylinder, no black smoke from 3406b, post ignition power source 2008 gmc sierra, recoding chevrolet silverado ignition, replacement resistor for dodge ac

2000-2006 TOYOTA TUNDRA VEHICLE WIRING INFORMATION

0

Filed Under (Toyota Manuals) by admin on 22-05-2011

download
WIRING INFORMATION: 2000 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 2001 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Doo

Related Content:

Blue Point Eecr2 Manual, 2003 chevy silverado instrument cluster ground wire, eecr2 manual, blue piont EECR2 manual, 2006 Tundra trailer wiring, toyota pbt-gf15, google com/wire harness repair 2007 impala, trailer hitch pbt gf15, honda crv 2000 central locking wiring diagram, honda pbt-gf15

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

mitsubishi canter (4D35) repair manual pdf, starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra

Jaguar Electronic Parking Brake Diagnostic Aid/ Repair Manual

0

Filed Under (Jaguar Manuals) by admin on 22-06-2012

download
INITIAL VISUAL INSPECTION 1. Place the vehicle on a suitable lift. 2. Visually inspect the parking brake cable installation, parking brake caliper levers and general condition of the brakes. • Ensure the caliper levers are returning fully to their stops. • Confirm the cable routing is correct • Confirm that the cable is securely fixed at all abutment points and is free to move within the C-clip. • Where cable routing goes over the top of the stabilizer bar drop links, confirm that the stabilizer bar rubber deflector blocks are fitted, and that the brake cables have not been getting trapped behind the stabilizer bar drop links (look for tell-tale marks on the links and/or cables). NOTE: Global Technical Reference (GTR) lookup sequence is as follows: GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual > 2: Chassis — Section 206: Brake System NOTE: Refer to the correct section by reference to VIN and based on whether the vehicle is fitted with high performance brakes or not. 3. Rectify any obvious faults. 4. If no obvious faults are found or further guidance is needed to rectify faults, please proceed to the next stage of this bulletin. Refer to GTR Sections 206-05 (parking Brake and Actuation) and GTR Section 206-04 (Rear Disc Brake). 5. If any faults were found and rectified, it will be necessary to re-calibrate the parking brake after rectification. See ‘Parking Brake Calibration’ procedure. PREPARE THE PARKING BRAKE FOR DETAILED INSPECTION CAUTION: Jaguar IDS DVD 111 or later and Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis. 1. Install the Midtronics PSC-550 Vehicle Power Supply to the vehicle. 2. Connect the IDS to the vehicle and begin a new diagnostic session by entering the correct VIN for the current vehicle. 3. Follow the IDS prompts to read the vehicle configuration. 4. Select ‘YES’ when prompted ‘Do you wish to read diagnostic trouble codes?’. 5. Follow all on-screen instructions to complete this task. 6. Select ‘Vehicle Configuration’ tab when the ‘Content Model’ is displayed. 7. Select ‘Electronic Parking Brake’. 8. Select ‘Release to Service Position’ (S-TYPE/XJ) or ‘Parking Brake Unjam Procedure’(XK) ‘. CAUTION: When using the special service tool, take care to operate in the ‘release’ direction. Actuator motor damage may result if the tool is operated in the ‘apply’ direction for any length of time). 9. If the parking brake will not release using IDS, use the special service tool to fully release the parking brake. Refer to GTR Section ‘Parking Brake Cable Tension Release’ (in Section 206-05) for details of using the special service tool.

Related Content:

GM Manuals Free Downloads, ids dvd111 download, 2003 Jaguar S Type Manual free download, 98 park avenue service manual free download, gm service manuals free download, Jaguar S Type Manual PDF, jaguar s type service manual

2004 Toyota Sienna POWER SLIDING DOOR INOPERATIVE Repair Manual

0

Filed Under (Toyota Manuals) by admin on 10-06-2012

download
Remove Slide Door Window Garnish. A. Fully open the slide door window. B. Remove the glass run. C. Using a screwdriver, disengage the clip and remove the garnish. HINT: Tape the screwdriver tip before use. D. Using the taped screwdriver, disengage the 2 claws and remove the inner weatherstrip from the garnish. Parts Information Repair Procedure Clip POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 3 of 7 2. Remove Side Trim Board Cover Rear. A. Remove the 2 screws. B. Using the taped screwdriver, disengage the 8 claws and remove the cover together with the window control switch. C. Remove the 2 screws and window control switch. 3. Remove Rear Door Trim Board Sub-assembly. A. Remove the screw. B. Using the taped screwdriver, disengage the 9 clips and remove the trim board. HINT: In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by the arrows in the illustration. 4. Remove Rail End Molding. A. Open the quarter glass. B. Using the taped screwdriver, disengage the clip and 2 claws, and remove the rail end molding. Repair Procedure (Continued) : Claw 1 2 3 4 5 5 4 3 2 1 Protective Tape Protective Tape : Clip : Clip : Claw POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 4 of 7 5. Remove Center Bracket No. 2. A. Remove the 2 bolts and Center Bracket No. 2 together with the tensioner (color: white). B. Remove the tensioner from Center Bracket No. 2. 6. Remove Center Bracket No. 1. A. Remove the 2 bolts and Center Bracket No. 1 together with the tensioner (color: black). B. Remove the tensioner from Center Bracket No. 1. 7. Remove Slide Door Window Assembly LH. A. With Sunshade: Remove the sun shade hook. B. Remove the bolt and window frame. C. Remove the bolt. D. Loosen the nut. E. Push the rear lower window frame in the direction indicated by the arrow in the illustration

Related Content:

remove plastic cover from side door sliding toyota sienna2008, findonefindall con/toyota sienna driver side window removal, how to remove toyota tundra back windo

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 27-06-2012

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

Related Content:

rockauto com 1999 ford winstar vent window bolt, ford 2001 f150 window removal, how to remove a rear hatch door on a Chev Trailblazer, F250 Rear Glass replace, 2011 ford F150 clunking rear end sound, 2010 Ford F150 rear window defroster harness, 2008 tahoe rear window button broken, how to install manual window door 04 f150, 2001fordf150rearwindowremoveal, 2004 f150 back window assembly

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering