replace ford f150 shifter tube

You search PDF repair manual about replace ford f150 shifter tube, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replace ford f150 shifter tube Direct Download speed 5432 Kb/s

  replace ford f150 shifter tube Full Version speed 8172 Kb/s



Ford F-Series Column Shift Repairs Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
It’s a simple system. To remove the assembly, start by removing the column shift lever. This is super easy; just use two small punches to depress the two spring-loaded pivot pins on the lever, then pull the lever out. Be aware: the pivot pins and spring will shoot out. Next go under the hood, and undo the two bolts holding the clamp piece just above the steering box. The lower half of the clamp will come free. The upper half is locked to the “shoe” plate under it, and to the steering column, with a round peg cast into it. So you need to pry the shoe up away from the steering column to get the peg clear of the column. Once you do that, you need to pry the upper half of the clamp away from the shoe, so the peg is clear of the shoe. Once it is clear, you can slide the end piece off the shifter tube. Then slide the wave washer and 2-3 lever off. To get the 1-R lever off, you’ll need to pull a steel pin out of the shifter tube. It should just drop out. Then slide the lever, wave washer, and shoe off the tube. Push the shifter tube up to get the clearance needed for the shoe. The shifter tube is a hollow steel tube, with a hole drilled thru it near the bottom. In this hole there is a steel pin (the one just removed). The steel pin engages into slots in the 1-2 and 3-4 levers, to move them. As you can see, there isn’t a lot of wear in my shift levers’ slots. The pin shows some wear, where the tube contacts it. The pin is hardened steel and the shifter tube is mild steel, so the tube will be worse than the pin. The pins are available from Obsolete Ford Parts and others, P/N 01A-7337, only a couple of bucks. Getting the shifter tube out is pretty easy; just drop the column support (remove the bolts to instrument panel and loosen the pinch bolt) down to the floor, and you’ll be able to swing the shift tube to the side to clear the steering wheel, and pull it out. My pin wasn’t that worn, it’s the hole in the tube. The tube is hollow but actually has a steel plug inside it with a hole for the pin. It is pushed inside the tube and then peened in two places thru the outer tube (they punched the outer tube to lock the inner plug). inner plug had gotten loose inside the tube, too. If this is your situation, you could just drill and pin the plug to the outer tube, and get a good improvement. I wanted “like new”, so I took my shifter tube to my favorite machinist (Gene at Noor Mfg. in Albuquerque, a super guy). He made up a whole new lower end for the tube out of 1018 carbon steel. It’s got a spigot on the upper end that was pressed into the remaining tube, welded, then turned down. It is better than new! Look at the difference in the shape of the hole. Price for the work was very reasonable

Related Content:

how do you replace an altenator on a 2005 honda pilot youtube, FREE INSTRUCTIONS ON SHIFTER TUBE REPLACMENT 2001 FORD F 150 /COLUMN SHIFTER, removing a 2000ford f250 shift tube, 96 windstar shifter tube clamp holder, 2005 chrysler town and country evaporatordraintube, where is the orifuce tobe on 1998 chevy silverado, yhs-jomedia, p01626, kia sedona ac drain hose clogged, how to installand adjust console shift handle 1999 ford taurus

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

how to replace solenoid e on a245e transmission problems, yhs-lavasoft, gm 4l60e band adjustment screws, 2005 explorer transmission exploded view, how to check tranmission fluid on 2012 kia sedona, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 2011 crv engine whine, manual pdf transmicion automatica ram 2001, 2004 saturn Clutch Assembly Exploded View

2006 Ford Five Hundred SE UPPER INTAKE MANIFOLD REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 30-11-2011

download
Removal All vehicles 1. Drain the cooling system. For additional information, refer to DRAINING . 2. Disconnect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 3. Remove the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 4. Remove the 4 transaxle roll restrictor cross brace bolts 5. Remove the bolt and the transaxle roll restrictor cross brace. 6. Disconnect the evaporative emissions (EVAP) canister purge valve tube from the upper intake manifold and detach the retainer. 7. Disconnect the positive crankcase ventilation (PCV), brake booster and vacuum harness tubes from the upper intake manifold. 8. Detach the fuel tube retainer from the upper intake manifold. 9. Disconnect the exhaust gas recirculation (EGR) system module electrical connector and vacuum tube. 10. Detach the vacuum tube from the upper intake manifold vacuum tube retainer. 11. Disconnect the EGR system module tube from the EGR system module. Early build 12. Disconnect and plug the throttle body and PCV coolant hoses. Late build 13. Disconnect and plug the 2 PCV coolant hoses. All vehicles 14. Disconnect the throttle body electrical connector. 15. If equipped, remove and discard the 4 upper-to-lower intake manifold screws. 16. Remove the 8 bolts and the upper intake manifold. * Remove and discard the gaskets. Installation All vehicles Fig. 4: Identifying Tightening Sequence Of Bolts Courtesy of FORD MOTOR CO. NOTE: Clean and inspect all sealing surfaces. Install new gaskets 1. Position the upper intake manifold and install the 8 bolts. * Tighten in the sequence shown to 10 N.m (89 lb-in). 2. Connect the throttle body electrical connector. Late build 3. Connect the 2 PCV coolant hoses. Early build 4. Connect the throttle body and PCV coolant hoses. All vehicle 5. Connect the EGR system module tube to the EGR system module. * Tighten to 40 N.m (30 lb-ft). 6. Attach the vacuum tube to the upper intake manifold vacuum tube retainer. 7. Connect the EGR system module electrical connector and vacuum tube. 8. Attach the fuel tube retainer to the upper intake manifold. 9. Connect the PCV, brake booster and vacuum harness tubes to the upper intake manifold. 10. Connect the EVAP canister purge valve tube to the upper intake manifold and attach the retainer. 11. Clean the 4 transaxle roll restrictor cross brace bolts using a wire brush and apply new threadlock to the threads. 12. Position the transaxle roll restrictor cross brace and install the 4 new bolts. * Tighten to 55 N.m (41 lb-ft). 13. Clean the transaxle roll restrictor cross brace-to-roll restrictor bolt using a wire brush and apply new threadlock to the threads. 14. Install a new transaxle roll restrictor cross brace-to-roll restrictor bolt. * Tighten to 48 N.m (35 lb-ft). 15. Install the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 16. Connect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 17. Fill and bleed the cooling system.

Related Content:

ford five hundred roll restrictor bushing diy, ford five hundred throttle body repair, fuel filler tube diagrams chevy impala 2003, pcv valve 3 0 ford aerostar where does small vacuum connection on pcv valve go

1997 Ford F-250/350/Super Duty Fuel Tank, Filters, Tubes and Electric Fuel Pump, Gasoline Engines Repair Manual

0

Filed Under (Ford Manuals) by admin on 17-05-2011

download
Item Part Number Description 1 370443-S32 Push-On Clip 2 9G291 Rear Fuel Vapor Return Tube 3 9A317 Fuel Tube Clip 4 9J337 Rear Fuel Supply and Return Tube 5 2269 Brake Tube 6 N802769-S Clip, Double 7 9291 Fuel Tube 8 N808716-S190 Retainer with Tether 9 9J338 Fuel Rail Tube 10 N802768-S Clip, Single 11 N605895-S2 Bolt 12 9K337 Fuel Tube Clip Support Bracket 13 N620480-S2 Nut 14 9002 Fuel Tank 15 9B033 Fuel Vapor Tube 16 9H334 Dual Fuel Supply and Return Tube 17 44878 Washer 18 N802826-S Screw 19 N620482-S2 Nut 20 383521-S Clamp 21 381114 Hose, 3/8-Inch 22 9H336 Front Fuel Tube and Hose 23 9A335 Fuel Filter Bracket 24 9B273 Fuel Filter to Fuel Pump Tube 25 N606678 Bolt

Related Content:

2004 ford f150 fuel vapor tube

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

FORD HIGH PRESSURE SYSTEM DIAGNOSTICS REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-04-2012

download
SERVICE PROCEDURE IT IS NOT NECESSARY TO REPLACE THE HIGH PRESSURE PUMP WHEN REPLACING THE A minimum of 3.5 MPa (500 psi or 0.8 volts) ICP is QUICK CONNECT FITTINGS. required before the injectors are enabled. No or low oil in the system, leakage at the injector upper 4. If a leak is identified in the branch tube, use D-rings, high pressure pump quick connect fitting, the following procedure to replace the branch high pressure pump discharge tube, faulty injection tube if the vehicle your working on is a F-Super pressure regulator (IPR), high pressure pump, or Duty or Excursion. For E-Series, the engine branch tube could cause low ICP pressure. needs to be removed to replace the branch tube. When replacing the branch tube, also 1. Perform the revised Powertrain Controls / install the STC bracket kit. Emissions Diagnosis (PC/ED) lead diagnostics Section 4, Hard Start / No Start Diagnostic BRANCH TUBE REPLACEMENT FOR F-SUPER Procedure Tests 10e and 10f. These tests were DUTY AND EXCURSION VEHICLES ONLY revised in January 2006. 1. Remove the transmission. See the appropriate NOTE model year Workshop Manual (WSM), Section 307-01. THE LOW PRESSURE OIL SYSTEM MUST BE WORKING PROPERLY IN ORDER FOR THE HIGH NOTE PRESSURE OIL SYSTEM TO BUILD ICP LEAVE THE FLYWHEEL ON THE ENGINE, AS IT PRESSURE. THIS INCLUDES ADEQUATE WILL MAKE IT EASIER TO TURN THE ENGINE PRESSURE AND GOOD QUALITY PROPERLY OVER TO TOP DEAD CENTER (TDC) AND THE MAINTAINED OIL. TRANSMISSION FLUID DOES NOT NEED TO BE NOTE DRAINED. THIS TSB ONLY APPLIES TO REPLACEMENT OF 2. Set engine at TDC both cylinder number 1 ANY COMPONENT FOUND DEFECTIVE WHILE rocker arms should be loose. See rocker arm PERFORMING PC/ED HARD START / NO START removal procedure in the appropriate online TESTS 10e AND 10f. WSM, Section 303-01C

Related Content:

2006 ford 500 service, 2006 ford 500 service manual, Ford 500 Repair Manual Download, kia high idling at start up

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

1997 Ford Explorer/ Mountaineer Intake Manifold Upper Repair Manual

0

Filed Under (Ford Manuals) by admin on 09-05-2012

download
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.

Related Content:

2000 mpv egr vacuum line, 1997 FORD EXPLORER VACUUM T SHAPPED HOSE, 2az fe intake manifold, 305 egr intke gasket, bad egr valve symptoms aveo chevrolet, upper air intake 2006 ford taurus pdf

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, ford 9 inch repair manual, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, heaf bolt torque specs 655a backhoe, windstar dtc u1131

Related Content:

how do you replace an altenator on a 2005 honda pilot youtube, FREE INSTRUCTIONS ON SHIFTER TUBE REPLACMENT 2001 FORD F 150 /COLUMN SHIFTER, removing a 2000ford f250 shift tube, 96 windstar shifter tube clamp holder, 2005 chrysler town and country evaporatordraintube, where is the orifuce tobe on 1998 chevy silverado, yhs-jomedia, p01626, kia sedona ac drain hose clogged, how to installand adjust console shift handle 1999 ford taurus