Skip to content

replace front wheel spindle on slk mercedes

You search PDF repair manual about replace front wheel spindle on slk mercedes, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997 Ford Aerostar/ Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

download
Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03 . 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03 . 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation

1994 Ford Explorer FRONT WHEEL BEARINGS MANUAL

download
FRONT WHEEL BEARINGS Dana 35-IFS & Automatic Locking Hubs 1. Raise and support vehicle. Remove front wheel assemblies. Remove retaining washers from wheel lug nut studs. See Fig. 1 . 2. Remove automatic locking hub assemblies. Remove snap ring and axle shaft spacer. Carefully pull plastic cam assembly from bearing adjusting nut. Remove 2 plastic thrust washers from adjusting nut. 3. Using magnet, remove locking key from spindle keyway. It may be necessary to rotate adjusting nut slightly to relieve pressure for locking key removal. Loosen adjusting nut with 2 3/8″ Hex Socket (T70T- 4252-B). 4. Tighten adjusting nut to 35 ft. lbs. (47 N.m) while turning hub back and forth to seat bearings. Spin hub and back off adjusting nut 90 degrees. Retighten adjusting nut to 16 INCH lbs. (1.8 N.m). 5. Align nearest hole in adjusting nut with center of spindle keyway slot. If necessary, advance nut to next lug. Install locking key in spindle keyway under adjusting nut. Install 2 thrust washers. Press plastic cam assembly onto adjusting nut while lining up key in fixed cam with spindle keyway. 6. Install axle shaft spacer. Clip snap ring onto end of spindle. Install automatic locking hub assembly with 3 legs of hub assembly inserted into 3 pockets of cam assembly. Install retaining washers and wheel assembly. Check hub and rotor assembly end play. End play should be 0-.003″ (0-.08 mm)

2000 BMW 528i (E39) DOHC Front Wheel Bearing Removal And Installation Manual

download
Replacing Front Wheel Bearing ( Wheel Hub )(Basis) Caution! Bearing cannot be dismantled. Do not wash out bearings. Remove brake disk (brake line remains connected), refer to Brakes and Traction Control; Disc Brake System. Remove ABS impulse sensor. Remove stabilizer link from stabilizer, Steering and Suspension. Unfasten nut. Installation: Use washer (1). Tapered spigot and bore both free of grease. Replace self-locking nut. Brace on hexagon socket if necessary. Tightening Torque, refer to Steering Specifications. Press off track rod with special tool 31 2 240. Mark the installation position of the spring strut tube (1) in the swivel bearing (2) with paint – never mark with scribing tool. Marking is not required if the factory mark is still identifiable. R installation position of right spring strut tube L installation position of left spring strut tube Version with factory marking above the swivel bearing. Unfasten nut. Expand swivel bearing with special tool 31 2 200 and pull swivel bearing downwards. Installation: Press swivel bearing upwards to stop with workshop hoist and note marking of installation position. Replace self-locking nut. Tightening Torque, refer to Suspension Specifications Unfasten screws and remove wheel bearing. Installation: Contact face (2) of wheel bearing and swivel bearing and the threaded bores (1) must be clean and free of grease. Tightening Torque, refer to Suspension Specifications

FRONT WHEEL SPEED SENSOR CORROSION REPAIR MANUAL

download
1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN 2002 CHEVROLET AVALANCHE 1999-2002 GMC SIERRA 2000-2002 GMC YUKON, YUKON XL LOCATED IN THE SEVERE CORROSION AREAS LISTED BELOW Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels. 3. Compress the front brake caliper pistons. 3.1. Install a large C-clamp over the top of the caliper housing and against the back of the outboard pad. 3.2. Slowly tighten the C-clamp until the pistons are pushed completely into the caliper bores. 3.3. Remove the C-clamp from the caliper. Important: It is not necessary to remove the front brake caliper from the bracket when removing the bracket in the next step. 4. Remove the two bolts that attach the front brake caliper mounting brackets to the knuckle. Notice: Support the brake caliper with heavy mechanic’s wire, or equivalent, whenever it is separated from its mount, and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. 5. Remove the brake caliper and bracket as an assembly and support it with heavy mechanic’s wire or equivalent. DO NOT disconnect the hydraulic brake flexible hose from the caliper. 6. Mark the relationship of the rotor to the bearing hub. 7. If equipped, remove the rotor retaining push nuts from the wheel studs

1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.