Skip to content

replace kia rio glove

You search PDF repair manual about replace kia rio glove, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Toyota Avalon, Camry, Camry Hybrid, Corolla, Highlander, Highlander CABIN AIR FILTER IDENTIFICATION / INSTALLATION MANUALHybrid, Matrix, Prius, RAV4, Sequoia, Tundra, Venza, Yaris

download
1. Open passenger side door. 2. Open glove compartment. 3. Remove screw holding damper rod in place on right side of glove compartment. 4. Detach damper rod from glove compartment. 5. Push in on left and right sides of glove compartment to release glove compartment. Filter Housing Cover 6. Flip down glove compartment. 7. Remove filter housing cover. Filter Housing Cover 8. Replace filter and reassemble

2004 Toyota Prius EV (Electric Vehicle) Button Installation Instructions

download
Time and Difficulty: I found the install to be moderately difficult and pretty time-consuming (about 3 hours) ; others have found it simple and report they have done it in as little as 30 minutes. Your experience will depend on your familiarity with the tools and electronics. I, personally, found insertion of the connection pin into the HV ECU plug to be difficult and almost got the first pin irrevocably stuck in the slot. I spent quite a bit of time with that part alone. I also found threading the wire behind the dash to be fairly tricky. I think the average person, not encountering any problems, could do this job in about 1-1½ hours. Procedure in Brief: 1) Remove bottom cover of steering wheel 2) Locate and unplug flasher plug 3) Open plug and remove 1-3 unused connector pins 4) Reattach steering wheel cover 5) Dismantle part of dash (vents) and remove lower glove box 6) Locate HV ECU (gray plugs) and remove lower plug 7) Solder wire to connector pin and insert into ECU plug (#27) 8) Splice EV button ground wire into ECU plug ground wire (#1) 9) Plug ECU plug back into the ECU 10) Thread wire behind dash to opening near dimmer switch 11) Attach switch to cover and solder wires in place 12) Reassemble the dash 13) Test Procedure in Detail: *Review ALL steps before proceeding and be sure you understand all terms used and you’ve looked at all diagrams and pictures. 1) Remove the bottom cover of the steering wheel by releasing the steering wheel adjustment handle and unscrewing the silver screw in that recess. 2004_prius_evv2.doc Page 4 of 20 Last updated March 13th, 2004 Then, turn the steering wheel 90 degrees right and remove the black screw that becomes visible on the right side of the steering column. Then turn the wheel 180 degrees left (90 degrees from normal position) and remove the black screw on the left side of the steering column. Carefully pull down on the lower portion of the steering column cover until it releases. Mine was a bit stiff/stuck to the upper part and you may need to carefully use a butter knife or screwdriver to start prying them apart. 2004_prius_evv2.doc Page 5 of 20 Last updated March 13th, 2004 2) Locate and unplug the white flasher plug visible just on the left side of the bottom of the steering column. 3) 2 little clips keep a cover locked in place. Pull those apart and remove the cover. Inside you’ll see lines of silver connector pins–some with wires attached, some without. You should remove between 1 and 3 of those pins–2 is probably safe, 3 might be better, since if you plan to install an OEM button at some point, you’ll probably need more pins for that. (You need one pin for the procedure, but it’s handy to have a back-up.) To remove the pins, you can use your paper clip to start the process of sliding them out, and then they just pull right out. 2004_prius_evv2.doc Page 6 of 20 Last updated March 13th, 2004 Stick them to a piece of tape or put them somewhere secure so you can find them later. Snap the cover back into place, and plug the flasher plug back in. 4) Replace the steering wheel cover by reversing the process. Be sure everything’s aligned properly and that there are no gaps. 5) Now you’ll need to dismantle part of the dash to get access to the ECU and other areas. First, open the top and bottom glove box doors. Squeeze the inside sides of the lower glove box together to get the catches past the portion of the dash frame that keeps the door from falling all the way open. Then pull the entire door straight toward you – it will unclip from the hinges at the bottom of the glove box. 2004_prius_evv2.doc Page 7 of 20 Last updated March 13th, 2004 You may also need to unclip the little hydraulic piston that keeps the door from falling open too quickly. Next, grasp the bottom of the silver vent piece next to the glove box. Pull it toward you firmly. It should unclip at the bottom first. Then pull the whole unit straight out

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)