replace lower suspension joint peugeot 106

You search PDF repair manual about replace lower suspension joint peugeot 106, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replace lower suspension joint peugeot 106 Direct Download speed 5432 Kb/s

  replace lower suspension joint peugeot 106 Full Version speed 8172 Kb/s



1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 13-06-2012

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, oem ball joint press, torqe for ball joint 2001 prizm, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, how to replace a balljoint on a 2002 buick lesabre, 08 silverado lower ball joint removal

Coil Spring Spacer Installation Instructions

0

Filed Under (More Manuals) by admin on 24-12-2011

download
1. Check to see that the spacer kit you purchased matches the year and model of your vehicle. Spacer kits two inches or taller may require a spring compressor to install. Ball joint and tie rod forks may also be useful. 2. A good portion of your front suspension will be disassembled so this would be a good time to replace any worn parts (i.e. tie rod ends, ball joints, idler arm and any bushings) Replace bushings with polyurethane replacement parts. 3. Jack up vehicle as high as possible using jack stands for support at all times. 4. With vehicle safely off the ground remove front tires. It is advisable to disassemble on side at a time so that you can use the other side as a reference for re-assembly in the event you get side tracked. 5. Remove the brake caliper from the rotor (attached with 2 bolts inside the caliper or with press-in clips depending on the vehicle). Do not remove the brake line from the caliper unless you intend to bleed the brakes at this time. Set the caliper aside or tie it up to the frame rail. Avoid pinching the brake line. 6. Remove the tie rod from the spindle using the proper tools. Do not hit the tie rod itself or the nut on the threaded portion of the tie rod or it may cause damaged and need replacing. 7. Remove the anti-sway bar from the lower control arm. This would be a good time to replace the end link bushings with polyurethane replacement bushings. 8. If your vehicle is equipped with anti-lock brakes you must now disconnect the front rotor sensor from the dust shield or spindle and set it aside. 9. Disconnect your shock absorber completely from the vehicle whether it is mounted inside the coil spring or not. 10. Support the lower control arm with jack just touching the arm. This will prevent it from dropping when the ball joint is disconnected. 11. The use of a coil spring compressor is recommended before the following steps are taken. 12. Disconnect the upper ball joint from the top of the spindle using the proper tools. Do not hit the ball joint or the threaded end of the ball joint. Once the ball joint is free the spindle should move easily. 13. Be careful when lowering the lower control arm. The coil spring is under high compression and may shoot out when released. Do not stand near the side of the truck during this step. Lower the jack so that the lower control arm swings down. If the coil spring has not fallen out on it’s own you may need to use a pry bar from the front of the vehicle to remove it. 14. Note which end of the coil spring is “bottom” for installation. Also note the depression in the lower control arm. It is important that the last winding of the coil spring fit into the indentation completely so that the vehicle will sit level. Do not switch coil springs from side to side as some vehicles have a specific “right” and “left” coil spring. 15. Check the coil spacer for proper fitment into the coil spring mount in the frame. The flat part of the spacer should face up and touch the top of the spring mount. Some vehicles have guiding tabs to center the coil spring in its top mount. These tabs may have become bent and need to be bent back to allow the spacer to properly fit in the mount. 16. Install the coil spring with the spacer on top of it. If used the coil spring compressor should still be on the spring in a compressed state. If it is not you may need to compress the spring before re-installing. Make sure the spacer is centered in the upper mount and the bottom of the spring is properly nested in the receptor groove on the lower control arm. If you are installing a two-inch or taller spacer you may need a spring compressor. Follow all safety rules when installing the coil spring as it will be under extreme compression. 17. Raise the lower control arm with a jack once the coil spring and spacer are properly lined up. Raise until the spindle is high enough to bolt on the upper ball joint. Before bolting on the upper ball joint make sure the brake caliper and brake line are where they need to be since some brake lines run inside the spindle and outside the coil spring. 18. With the upper ball joint tight and a cotter pin re-installed you may now remove the jack from under the lower control arm. 19. Assemble all of the components previously removed (sway bar with new polyurethane bushings, tie rod ends with polyurethane grease boot, brake caliper and anti-lock sensor). Don’t forget the shock with a new colored boot while it is off. 20. Repeat instructions for other side. 21. After properly installing both spacers you can install your front tires and lower vehicle back to the ground. 22. Your vehicle may sit too high at first because the suspension needs to settle. Carefully back the vehicle up and drive forward a few times using the brakes frequently. Park on level ground and check out your lift. 23. The vehicle will now require a front wheel alignment. Failure to do so may result in severe wear on your tires and may pull to one direction

Related Content:

1997 ford ranger coil spring spacer installation, 4L60E 3 4 Accumulator Assembly, how to replace rear coil spring on a buick rendezours, how to use evertough coil spring compressor, Jeep TJ coil spring perch, labor to replace control arms g6, metal clip on ow beam 2009 mazda 6, ranger coil spring replace, replace 2006 Impala control arm bushings, replacing rear springs for 2004 toyota sienna

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

2008 Honda Accord L4-2.4L Knuckle/ Hub Bearing Unit Replacement

0

Filed Under (Honda Manuals) by admin on 19-11-2011

download
Hub Bearing Unit Replacement 1. Raise the rear of the vehicle, and support it with safety stands in the proper locations. 2. Remove the wheel nuts, and the rear wheel. 3. Remove the brake hose mounting bolt (A). 4. Remove the brake caliper bracket mounting bolts (B), then remove the caliper assembly (C) from the knuckle. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper assembly from the undercarriage. Do not twist the brake hose excessively. 5. Remove the two washers (A). NOTE: During installation, make sure the washers are installed between the brake caliper bracket and the knuckle. 6. Remove the rear brake disc. 7. Remove the hub bearing unit (A) and O-ring (B). 8. Check the hub bearing unit for damage and cracks. 9. Install the hub bearing unit in the reverse order of removal, and note these items: * Use a new O-ring on reassembly. * After installing the brake caliper, make sure the clearance between lower arm B and the parking brake cable is more than 5 mm (3/16 in.). * Before installing the brake disc, clean the mating surfaces of the hub bearing unit and the brake disc. * Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the wheel. * Check the wheel alignment, and adjust it if necessary. Knuckle Replacement 1. Remove the hub bearing unit. 2. Remove the splash guard (A). 3. Remove the lock pin (A) from the upper arm ball joint, then remove the castle nut (B). NOTE: During installation, install the lock pin as shown after tightening the new nut. 4. Disconnect the upper arm ball joint from the knuckle using the ball joint remover. NOTE: * Be careful not to damage the ball joint boot when installing the remover. * During installation, to connect the ball joint, raise the suspension with a jack. 5. Remove the wheel speed sensor (A) from the knuckle. Do not disconnect the wheel speed sensor connector. 6. Remove the self-locking nut (A) while holding the joint pin (B) with a hex wrench (C), then disconnect the stabilizer link (D) from the knuckle, and remove the brake hose bracket (E). NOTE: Use a new self-locking nut during reassembly. 7. Remove the damper lower mounting bolt (F). NOTE: Use a new mounting bolt during reassembly. 8. Remove the control arm mounting self-locking nut (A) and washer (B). NOTE: Use a new self-locking nut during reassembly 9. Remove the lower arm mounting bolt (A), and the lower arm B mounting bolt (B), then remove the knuckle (C). NOTE: Use new mounting bolts during reassembly. 10. Install the knuckle in the reverse order of removal, and note these items: * First install all the components, and lightly tighten the bolts and nuts, then raise the suspension to load it with the vehicle’s weight before fully tightening to the specified torque values. * Be careful not to damage the ball joint boot when connecting the knuckle. * Before connecting the ball joint, degrease the threaded section and tapered portion of the ball joint pin, the ball joint connecting hole, and the threaded section and mating surface of the castle nut.

Related Content:

2008 F250 STEERING GEAR PITMAN ARM NUT SIZE, bearing retaining nut for a 2004 Trailblazer, brake caliper dust boot honda 2007 accord coupe

1996 Toyota Supra A/T TRANSMISSION REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 16-03-2012

download
Removal 1) Disconnect negative battery cable. Remove battery, battery tray, air cleaner assembly and air cleaner case. Disconnect throttle valve cable from throttle body. Remove cruise control actuator with mounting bracket from body. 2) Raise and support vehicle. Disconnect necessary electrical connectors and ground cables for transaxle removal. Disconnect shift cable and oil cooler lines at transaxle. Remove shift cable clamp bracket from transaxle. 3) Remove front (radiator side) engine mount shock absorber- to-lower frame assembly bolts. Remove front (radiator side) engine mount-to-lower frame assembly bolts/nuts. Remove starter. 4) Remove front (radiator side) exhaust manifold brace from rear of exhaust manifolds. Brace fits between rear of exhaust manifold and front of transaxle. 5) Remove 4 upper transaxle-to-cylinder block bolts. Support engine with hoist. Steering gear assembly must be supported in place during transaxle removal. Secure steering gear assembly to engine hoist using an attaching strap placed at each end of steering gear assembly. 6) Remove front wheels. Remove front exhaust pipe located between exhaust manifolds and rear exhaust pipe. Drain transaxle fluid. Remove axle shafts from transaxle. See appropriate AXLE SHAFTS article in AXLE SHAFTS & TRANSFER CASES section. 7) Disconnect shift control cable from mounting bracket. Remove rear (firewall side) engine mount-to-lower frame assembly bolts/nuts. Remove transaxle mount-to-transaxle bolts at driver’s side end of transaxle. 8) Remove stabilizer bar mount bracket-to-lower frame assembly bolts. Remove steering gear assembly-to-lower frame assembly bolts/nuts. Support lower frame assembly with floor jack. Lower frame assembly is located below engine and transaxle. 9) Disconnect power steering reservoir pipe mounting brackets from lower frame assembly. Remove bolts for each fender liner from lower frame assembly. Remove lower frame assembly mounting brackets. Lower frame assembly mounting brackets are located on front and rear of lower frame assembly and attach lower frame assembly to body. Remove lower frame assembly. 10) Support transaxle with transmission jack. Remove torque converter cover from front of transaxle. Remove torque converter bolts. Remove remaining exhaust manifold support brace. Remove remaining transaxle-to-cylinder block bolts. Lower transaxle from vehicle.

Related Content:

1972 chevelle assembly manual, 70 Chevelle Horn Assembly diagram, exploded view air intake assembly 2006 honda accord, 70 Chevelle Horn Assembly Schematic, how to replace fog light assembly on 2012 toyota seinna, hunter l401 parts list, replacing transaxles on 2006 chevy impala, pt cruiser gear shift assembly, Sienna 2012 fog light assebly removal and replacement, Sienna 2012 fog light assembly removal and replacement directions

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, 2011 crv engine whine, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio, how to adjust the bands of an automatic trasmission of hyundai accent 2002

Ball Joint Spacers for IFS Suspension

0

Filed Under (More Manuals) by admin on 20-12-2011

download
1) Block rear wheels, place front end of truck on jack stands supported on the frame and remove the front wheels. 2) Remove the original upper ball joint hardware. 3) Knock the studs out of the ball joint with a small hammer. This is done most easily if the joint is pressed against the arm supported with a floor jack. 4) Remove the factory shock. 5) Trim the lip. An angle grinder with a cut-off wheel or a small reciprocating saw works well. Trim enough to allow installation of the spacer. 6) Put the spacer in place, NOTCH FACING DOWNWARD and, using a floor jack to control arm height, align the ball joint and install the hardware. The notch acts as a weep hole to let any water that gets in from above drain out to prevent the ball joint from rusting out. 7) Tighten ball joint hardware using the provided nylon lock nuts. 8) Install new extended length shock. 9) Repeat for other side. 10) Re-install the wheels. 11) If the end of the upper control arm is too close to the tire at this point, there are a few options: • You can replace your wheels with a higher off-set. • You can add a 1/4″ wheel spacer to move the wheel/tire away from the suspension. 12) Put the vehicle back on the ground. 13) For low profile bump stops only: • Shim them approx. 1/2″ with some washers or use stock bump stops. • Failure to do so could result in damage to CV joints, shocks, or other components 14) Even with stock bump stops, you may experience some CV axle binding. • To check, let the suspension hang’ at full droop. • Rotate each CV axle shaft by hand and check for any binding at the CV joints. • If felt, several options to fix it are available: o Add some shims for the low profile bump stops. o Or install a front differential drop kit to lower the differential and thus lessen the CV joint angles.

2000-2006 TOYOTA TUNDRA 2WD AND 4WD 6″ SUSPENSION SYSTEMS INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 03-03-2012

download
FRONT INSTALLATION INSTRUCTIONS 1. On 4WD models only, remove grease cap, cotter pin and locking cap. (Illustration 1) While applying the brakes, loosen both Driver side and Passenger front axle nuts but do not remove. 2. Raise the vehicle. If working without a shop hoist, support vehicle with suitable safety jack stands. Put vehicle in gear, set emergency brake and block rear wheels, both in front and behind tires. Loosen front wheel lug nuts. Place floor jack under the lower control arm’s front crossmember and raise vehicle. Place safety jack stands under frame rails, behind front wheel wells, and lower the frame onto the stands. Once securely on jack stands remove floor jack. Remove front wheels. Illustration 1 7 RCD Suspension 619-588-4723 3. Place a jack under front lower a-arm. Remove lower nut from front shock mount. Next, locate the three nuts at the top of the front shock. (Illustration 2) Remove these nuts, lower the a-arm and remove front shock. Repeat on opposite side of vehicle. 4. Locate and remove the nut, retainer collar and cushion that attaches the Sway Bar end to the lower a-arms. (Illustration 3) Remove the two brackets that attach the Sway Bar to the frame. (Illustration 4) Stock Sway Bar can be discarded but make sure to keep original mounting brackets. 5. Detach bolt and brake line hose clamp from the front spindle. (Illustration 5) Next, remove the two bolts that attach the brake caliper to the front spindle. Remove the brake caliper and tie it up with safety wire. DO NOT LET IT HANG BY THE BRAKE LINE. Illustration 2 Illustration 3 Illustration 4 Illustration 5 8 RCD Suspension 619-588-4723 6. Remove rotor using snap ring pliers to remove inner snap ring. (Illustration 6) (Some models may not have snap ring and rotor can just be removed at this point) 7. Remove Cotter pin and loosen nut located on upper front ball joint. (Illustration 7) (on 4WD models use a strap to support the Front Drive Axle and keep it from resting at full bind) Using Ball joint puller, remove upper control arm from spindle. 8. Next, remove the cotter pin and nut located at the Tie Rod End on the Spindle. Using the Tie Rod Puller, disconnect the Tie Rod from the Spindle. (Illustration 8) 9. On 4WD models remove the axle nut. On ABS equipped vehicles, detach the ABS speed sensor from stock spindles. 10. Locate the four bolts attaching the Lower Ball Joint on the a-arm to the front spindle. (Illustration 9) Remove the bolts and take spindle off of vehicle. 11. Repeat steps 5 through 10 on opposite side of vehicle

Related Content:

best way to remove o2 sensor on 2000 tundra limited v8, d2000 mitsubishi rear axle, jack points for toyota tundra

Toyota Front Coil Spring Spacer Lift Kit Installation Manual

0

Filed Under (Toyota Manuals) by admin on 22-12-2011

download
INSTALLATION INSTRUCTIONS FRONT 1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, ball joint separator, jack stands, bench vise, and metric hand tools. 2. Jack the vehicle in the center of the front cross member. 3. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the ground. 4. Remove the front tires/wheels. 5. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut. 6. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool, be careful NOT to damage the ball joint boot) 7. Remove upper strut tower nuts holding strut assembly to strut tower (3) on each side of vehicle. 8. Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle. (Note the direction of the bolt for reinstallation) 9. Compress the coil spring on the strut assembly with a suitable coil spring compressor so that the coil spring has about 3/8″ play in the strut and remove the upper strut isolator mount nut. 10. Remove the coil spring isolator from the upper strut mounting plate. 11. Replace the upper strut mounting plate studs with the supplied studs with a bench vise and a deep well socket. (3 on each side) 12. Reinstall the factory coil spring isolator to the upper strut mounting plate. 13. Reinstall the compressed coil spring onto the strut assembly and reattach the upper strut mount plate using the stock hardware. See diagram. Torque upper strut mounting plate nut to 18 foot-pounds. 14. Decompress the coil spring in the strut assembly. Make sure that the spring is seated correctly into the strut assembly alignment indentation at the bottom of the strut and the top isolator. 15. Slide the coil spring spacer onto the top of the strut assembly over the 10mm studs. 16. Install the strut assembly into the strut tower and start the upper three 10mm lock nuts. (Make sure that the bottom of the strut is aligned as well) 17. Install the lower strut bolt in the original position and torque to 100 foot- pounds. (Step 8) 18. Using the floor jack, raise the lower control arm and connect the upper ball joint on the upper control arm to the spindle. Torque nut to 80 ft lbs. and make sure that you replace the cotter pin. (Not supplied) 19. Install the front tires/wheels. 20. Lower the vehicle onto the ground and tighten the upper strut tower 10mm nuts. Torque to 35 foot-pounds. (3 on each side) 21. RETORQUE ALL BOLTS AFTER 500 MILES.

Related Content:

sienna manual powered struts open manually, how man ft lbs for cadilla dts strut, strut removal ford crown victoria 2010 instruction, how to install lift support struts on 2006 Toyota Sienna, How to install lift gate struts, how to change out hatch struts on a toyota sienna, change struts lincoln ls, honda pilot strut replacement, Front strut replacement 1997 Ford Thunderbird, ford torque strut bushing

1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs for 5 7 volvo penta exhaust manifold, torque specs 4 8 chevrolet, rod torque botyom end n14, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, oem ball joint press, torqe for ball joint 2001 prizm, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, how to replace a balljoint on a 2002 buick lesabre, 08 silverado lower ball joint removal