Skip to content

replace pinion seal on 2004 supercrew

You search PDF repair manual about replace pinion seal on 2004 supercrew, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

2004-2005 FORD F-150 FRONT BRAKE ROUGHNESS/ SHUDDER WHILE BRAKING REPAIR MANUAL

download
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.

2005 Ford F-150 Drive Pinion Flange and Drive Pinion Seal Repair Manual

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 . 2. Remove the brake disc. For additional information, refer to Section 206-04 . 3. Index-mark the driveshaft flange and pinion flange for correct alignment during installation. 4. Remove the 4 driveshaft flange bolts. 5. NOTE: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the driveshaft centering socket yoke from the pinion flange. Pry only in the area shown with a suitable tool to disconnect the driveshaft centering socket yoke from the pinion flange. Using a suitable tool as shown, disconnect the driveshaft centering socket yoke from the pinion flange. ? Using mechanic’s wire, position the driveshaft aside. 6. Using a Nm (lb-in) torque wrench on the pinion nut, record the torque required to maintain rotation of the pinion gear through several revolutions. 7. Using the special tool to hold the pinion flange, remove and discard the pinion nut.2005 F-150 Workshop Manual 8. Index-mark the pinion flange in relation to the drive pinion stem to make sure of correct alignment during installation. 9. Using the special tool, remove the pinion flange. 10. Force up on the metal flange of the drive pinion seal. Install gripping pliers and strike with a hammer until the drive pinion seal is removed. Installation 1. Lubricate the new drive pinion seal with grease. 2. Using the special tool, install a new drive pinion seal. 3. Lubricate the pinion flange splines with axle lubricant. 4. NOTE: Disregard the scribe marks if a new pinion flange is being installed. Align the pinion flange with the drive pinion shaft. 5. Using the special tool, install the pinion flange. 6. l a new pinion nut with the same iginal if not replacing the collapsible spacer. If a installed, install the nut in the kit, as indicated in the chart below, or damage to the component may occur. Position the new pinion nut. Pinion Nut 7. no circumstances ut to be backed off to reduce drive pinion bearing preload. If reduced drive pinion bearing preload is required, a new drive pinion collapsible spacer and pinion nut must be installed or damage to the component may occur. NOTE: Remove the special tool while taking drive pinion bearing preload readings with the Nm (lb-in) torque wrench. Using the special tool to hold the pinion flange, tighten the pinion nut. ? Rotate the drive pinion occasionally to make sure the drive pinion bearings are seating correctly. ? Install a Nm (lb-in) torque wrench on the pinion nut. ? Rotating the drive pinion through several revolutions, take frequent drive pinion bearing preload readings until the original recorded drive pinion bearing preload reading is obtained. ? If the original recorded drive pinion bearing preload is lower than specification, tighten to the appropriate specification for used drive pinion bearings. If the drive pinion bearing preload is higher than specification, tighten the pinion nut to the original reading as recorded. For additional information, refer to the Specification portion of this section. 8. Position the driveshaft and align the index mark on the pinion flange.