Skip to content

replacing air blend door actuator on 2006 chevy impala

You search PDF repair manual about replacing air blend door actuator on 2006 chevy impala, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

2001 – 2006 TOYOTA Sequoia BACK DOOR POWER WINDOW INOPERATIVE

download
BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 2 of 6 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Plastic Pry Tool Set* NOTE: All components from this kit/set are required 00002-06000-01 1 21 *Essential SSTs. **Refers to drawer number in SST Storage System. NOTE: Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335. 1. Disconnect the negative (-) terminal of the vehicle battery. NOTE: Any time the negative (-) battery terminal has been disconnected, systems requiring initialization will need to be re-initialized after the negative (-) battery terminal has been reconnected. 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. Required SSTs Repair Procedure : 5 Clips : 3 Clips BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 3 of 6 5. Remove the strap cover, bolt, and pull strap. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9. 9. For 2005 – 2006 model year Sequoia vehicles ONLY: Remove the multiplex network door ECU. Using a drill of less than 3.2 mm (0.126 in.), drill out the two (2) rivet heads. HINT: Gently and vertically put the drill to the rivets and cut the rivet flanges. CAUTION: Take care as the cut rivets may be HOT. 10. For 2005 – 2006 model year Sequoia vehicles ONLY: Install the replacement multiplex network door ECU and rivets

1993 BMW 325i (E36) Removing and Installing/ Replacing Heater and Air Conditioning Fan (M50, S50, M52)

download
With Air Conditioning Notes Removing and Installing/Replacing Heater and Air Conditioning Fan (M50, S50, M52) * Additional work on 2-door model: Remove console for the windshield wiper system. * Position windscreen wiper, left, vertically. * Pull off rubber part and pry out grill. Zoom Sized for Print Zoom Sized for Print * Remove screws from cable channel. * Remove screws on right-hand side and take off holder. * Unscrew left-hand screw. * Pull out air collector in upwards direction. Note: Air collector will be difficult to pull out. M50, M52 Unclip covers. Unscrew bolts. Remove cover of injection-valve plate. * Unclip covers and remove screws. * Remove cover * Unfasten clips and remove blower cover. * Disconnect connector. * Unfasten clips and lift out left upper section of blower. Note: The air conditioning system remains installed. Illustration shows air conditioning unit removed.

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.