Skip to content

replacing heater core 2001 monte carlo ss

You search PDF repair manual about replacing heater core 2001 monte carlo ss, if there are search results will appear below. If search results do not exist, please search by others keyword.

1993 BMW 325i (E36) Removing and Installing/ Replacing Heater and Air Conditioning Fan (M50, S50, M52)

download
With Air Conditioning Notes Removing and Installing/Replacing Heater and Air Conditioning Fan (M50, S50, M52) * Additional work on 2-door model: Remove console for the windshield wiper system. * Position windscreen wiper, left, vertically. * Pull off rubber part and pry out grill. Zoom Sized for Print Zoom Sized for Print * Remove screws from cable channel. * Remove screws on right-hand side and take off holder. * Unscrew left-hand screw. * Pull out air collector in upwards direction. Note: Air collector will be difficult to pull out. M50, M52 Unclip covers. Unscrew bolts. Remove cover of injection-valve plate. * Unclip covers and remove screws. * Remove cover * Unfasten clips and remove blower cover. * Disconnect connector. * Unfasten clips and lift out left upper section of blower. Note: The air conditioning system remains installed. Illustration shows air conditioning unit removed.

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation Manual

download
Evaporator Core Housing Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screws from the RH fender apron and remove the fender apron. 7. Remove the nuts. 8. Lower the vehicle. 9. Remove the blower motor switch resistor. For additional information, refer to Section 412-04 . 10. Disconnect the connector. 11. Disconnect the evaporator to compressor suction line from the suction accumulator drier. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 12. Disconnect the condenser to evaporator tube from the A/C evaporator core inlet tube. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 13. Remove the nuts and position the purge valve and backet away from the evaporator core housing. 14. Remove the heater hoses from the heater core. 15. Disengage the connectors fom the bracket. 16. Disconnect the connector. 17. Remove the nut and reposition the wire harness away from the evaporator housing. 8 18. Disengage the harness from the bracket. 19. Remove the pin-type retainer and clip and remove the instrument panel lower insulator. 20. Fold back the carpet and remove the screw. 21. Inside the vehicle, remove the screw. 22. Remove the nuts(engine side).