replacing timing chain envoy 03 4

You search PDF repair manual about replacing timing chain envoy 03 4, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replacing timing chain envoy 03 4 Direct Download speed 5432 Kb/s

  replacing timing chain envoy 03 4 Full Version speed 8172 Kb/s



2000 Dodge Intrepid Timing Chain Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 21-11-2011

download
REMOVAL 1.Remove upper intake manifold. 2.Remove cylinder head covers, crankshaft damper, and timing chain cover. CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. Fig. 70 3.Align crankshaft sprocket timing mark to mark on oil pump housing (Fig. 70). The mark on oil pump housing is 60° ATDC of #1 cylinder. CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage Fig. 74 4.Remove primary timing chain tensioner from right cylinder head (Fig. 74). 5.Remove camshaft position sensor from left cylinder head (Fig. 69). 6.Remove chain guide access plug from left cylinder head (Fig. 69). NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction. 7.Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper and sprocket (Fig. 69). 8.Remove left side camshaft sprocket attaching bolts and remove sprocket (Fig. 69). 9.Remove lower chain guide and tensioner arm (Fig. 69). 10.Remove the primary timing chain. INSTALLATION 1.Inspect all sprockets and chain guides. Replace if worn. Refer to Crankshaft Gear/Sprocket, for removal and installation procedures. 2.If removed, install right and left side short chain guides (Fig. 69). Tighten attaching bolts to 28 Nm (250 in. lbs.) 3.Align crankshaft sprocket timing mark to the mark on oil pump housing (Fig. 71). NOTE: Lubricate timing chain and guides with engine oil before installation. 4.Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (Fig. 71). 5.Lower the primary chain with left side sprocket through the left cylinder head opening

Related Content:

diagram of a 00 lincoln ls 3 9 liter timing chain and gears, 2006 trailblazer timing marks, 2004 pontiac sunfire timing chain replacement, 04 ford escape timing chain settings, tdc on jaguar 4 0, sport trac timing chain replacement interval, is crankshaft position sensor removed when replacign timing chain on 2001 durango, installing timing chain on 2000 dodge ram 1500, how to replace the timing chain on a 2004 maxima 3 5, the manual repair of the timing chain 4 strokevideo

CHAIN SUB-ASSEMBLY (2AZ-FE) REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 17-05-2012

download
INSTALL CHAIN TENSIONER SLIPPER a. Install the chain tensioner slipper with the bolt. Torque: 19 Nm (194 kgf-cm, 14 ft. lbs.) Zoom Sized for Print 36. INSTALL TIMING CHAIN GUIDE a. Install the timing chain guide with the bolt. Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) Zoom Sized for Print 37. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO.1 a. Install the sensor plate with the “F” mark facing forward. 38. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL a. Apply multipurpose grease to a new oil seal lip. NOTICE: Keep the lip free of foreign objects. Zoom Sized for Print b. Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge. SST 09223-22010 39. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY a. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block. Zoom Sized for Print b. Apply a continuous bead of seal packing (Diameter 2.0 mm (0.079 inch) ) as shown in the illustration. Seal packing: Part No. 08826-00080 or equivalent Zoom Sized for Print NOTICE: • Remove any oil from the contact surface. • Install the chain cover within 3 minutes of applying seal packing. • Do not put in engine oil for at least 2 hours after installing the chain cover. c. Apply a continuous bead of seal packing as shown in the illustration. Seal packing: Part No. 08826-00080 or equivalent NOTICE: • Remove any oil from the contact surface. • Install the chain cover within 3 minutes of applying seal packing. • Do not put in engine oil for at least 2 hours after installing the chain cover. Zoom Sized for Print d. Install the timing chain cover with the 14 bolts and 2 nuts. Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) for bolt A 25 Nm (255 kgf-cm, 18 ft. lbs.) for bolt B 55 Nm (561 kgf-cm, 41 ft. lbs.) for bolt C 43 Nm (438 kgf-cm, 32 ft. lbs.) for bolt D 11 Nm (112 kgf-cm, 8 ft. lbs.) for nut

Related Content:

bolt pattern for the timing cover of 5 4L triton, Ford 5 0 Timing Cover bolt diagram, Seal Packing 08826 00080

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, 2002 diamante timing belt, 2003 eclipsed2 4 litre cranckshaft position sensor location, should the timing arrow on a zx2 move when belt is pressed, 2002 jetta crank mark, kia rio 5 2007 timming belt, 3126 timing pin hole, 91 honda accord timing belt marks diagram, 98 eclipse rs service manual

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 10-05-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

Related Content:

1997 saturn manifold repair, 2000 lexus es 300 gear sprocket, 2007 SATURN RELAY 3 9 V6 TIMING CHAIN/ MAGNETIC SPROCKET

1995 Nissan-Datsun 200SX Timing Chain/ Front Cover Revised Procedure

0

Filed Under (Nissan Manuals) by admin on 27-01-2012

download
Removal 1. Set # 1 piston at TDC on its compression stroke. 2. Remove the spark plug wires. 3. Remove the rocker cover (see Figure 1). 4. Remove the coolant reservoir tank with bracket and reposition it for clearance. 5. Support the engine with a suitable jack. 6. Remove cylinder head front mounting bracket. 7. Remove engine front mounting, then the engine front mounting bracket. 8. Remove cylinder head front cover 9. Remove the upper chain tensioner (see Figure 2). 10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with the timing marks on the cam sprockets and idler sprocket (see Figure 3) 11. Remove the four (4) front cover to cylinder head bolts. 12. Remove side and lower engine compartment splash covers. 13. Remove the accessory drive belts. 14. Remove the crankshaft pulley. 15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain cock (Refer to MA section of the Service Manual). 16. Drain engine oil. 17. Remove intake manifold support of engine front side. 18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance. 19. Remove the thermostat housing (See Figure 4) 20. Remove the lower chain tensioner (see Figure 5). 21. Remove the front exhaust tube. Refer to the “FE” section (Exhaust System) of the Service Manual. 22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan. NOTE: On A/T models, remove the rear plate cover. 23. Remove the oil pan (see Figure 6). a. Insert the Tool between the cylinder block and oil pan. CAUTION: Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged. b. Slide the Tool by tapping it on the side of the Tool with a hammer. 24. Remove the A/C compressor and position it aside for clearance. 25. Remove the A/C and alternator bracket with the alternator. 26. Remove the oil pump drive spacer. CAUTION: Be careful not to scratch the drive spacer when removing it. 27. Remove the front cover bolts and front cover. CAUTION: One bolt is located on the water pump (see Figure 7). *1: Located on engine front mounting bracket. *2: Located on the water pump. *3: Located on the power steering oil pump adjusting bar. CAUTION: Be careful not to tear or damage the cylinder head gasket. 28. Remove the cylinder block to front cover alignment dowels. CAUTION: Do not hit the dowels or the cylinder block will crack. 29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8). Installation 1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine. 2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process. CAUTION:

Related Content:

remove nissan quest tension timing, 2001 mercury cougar cylinder head removal, timing marks in 07 kia optima, timing chain tensioner removal 04 quest, timing chain for lincoln ls 04 b8, nissan quest timing chain tensioner replacement, mazda 6 timing marks, 2011 escape timing belt, 2005 gmc envoy timing chain, 2005 Altima 2 5 Timing Marks

2004 Dodge Truck RAM 1500 Truck 2WD TIMING CHAIN AND SPROCKETS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 10-06-2012

download
TIMING CHAIN AND SPROCKETS Precaution: Timing Chain Replacement CHAIN GUIDES AND TENSIONER ARMS: Replace these parts if grooving in plastic face is more than 1 mm (0.039 inch) deep. If plastic face is severely grooved or melted, the tensioner lube jet may be clogged. The tensioner should be replaced. REMOVAL 1. Disconnect negative cable from battery. 2. Drain cooling system . 3. Remove right and left cylinder head covers. 4. Remove radiator fan shroud. 5. Rotate engine until timing mark on crankshaft damper aligns with TDC mark on timing chain cover (Fig. 132) (# 1 cylinder exhaust stroke) and the camshaft sprocket “V8″ marks are at the 12 o’clock position (Fig. 133). 6. Remove power steering pump. 7. Remove access plugs (2) from left and right cylinder heads for access to chain guide fasteners (Fig. 134). 8. Remove the oil fill housing to gain access to the right side tensioner arm fastener. 9. Remove crankshaft damper and timing chain cover. 10. Collapse and pin primary chain tensioner (Fig. 135). CAUTION: Plate behind left secondary chain tensioner could fall into oil pan . Therefore, cover pan opening. 11. Remove secondary chain tensioners. 12. Remove camshaft position sensor from right cylinder head (Fig. 136). CAUTION: Care should be taken not to damage camshaft target wheel. Do not hold target wheel while loosening or tightening camshaft sprocket. Do not place the target wheel near a magnetic source of any kind. A damaged or magnetized target wheel could cause a vehicle no start condition. CAUTION: Do not forcefully rotate the camshafts or crankshaft independently of each other. Damaging intake valve to piston contact will occur. Ensure negative battery cable is disconnected to guard against accidental starter engagement. 13. Remove left and right camshaft sprocket bolts.

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 09-06-2012

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

Related Content:

toyota tacoma 2000 REMOVE COMPRESSOR DRIVE BELT, 2002 ford ranger 2 3L timing tool, 2002 nissan altima changing camshafts, 2002 toyota tundra manual, Centurial Timing Module

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Related Content:

free download Service Manual for a 1992 Toyota Truck, Toyota 5K ignition, _1987_Nissan_pickup_v6 destributer timing marks

Related Content:

diagram of a 00 lincoln ls 3 9 liter timing chain and gears, 2006 trailblazer timing marks, 2004 pontiac sunfire timing chain replacement, 04 ford escape timing chain settings, tdc on jaguar 4 0, sport trac timing chain replacement interval, is crankshaft position sensor removed when replacign timing chain on 2001 durango, installing timing chain on 2000 dodge ram 1500, how to replace the timing chain on a 2004 maxima 3 5, the manual repair of the timing chain 4 strokevideo